Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Mine Surveying: Mine Plans and Curves

Mining Engineering · Mine Surveying

33 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is a contour line?

  1. A line joining points of equal grade
  2. A line joining points of equal elevation
  3. A railway line
  4. A boundary line
Show answer & solution

Answer: (B) A line joining points of equal elevation

Contours show the shape of the ground surface.

Question 2

What is the contour interval?

  1. The length of a contour
  2. The scale of the map
  3. The vertical distance between successive contour lines
  4. The horizontal distance between contours
Show answer & solution

Answer: (C) The vertical distance between successive contour lines

The contour interval is constant on a given map.

Question 3

What do closely spaced contours indicate?

  1. A steep slope
  2. A lake
  3. Flat ground
  4. A gentle slope
Show answer & solution

Answer: (A) A steep slope

Wide spacing shows gentle slopes.

Question 4

When can contour lines cross each other?

  1. At every ridge
  2. Only at an overhanging cliff or cave
  3. At every valley
  4. Whenever the slope is gentle
Show answer & solution

Answer: (B) Only at an overhanging cliff or cave

Normally, contours of different elevations never cross.

Question 5

What do V-shaped contours with the V pointing uphill indicate?

  1. A flat plain
  2. A ridge
  3. A valley
  4. A hilltop
Show answer & solution

Answer: (C) A valley

V-shapes pointing downhill indicate a ridge.

Question 6

Why must up-to-date mine plans be maintained under mining regulations?

  1. For safe planning, avoiding old workings, staying within boundaries and use in emergencies
  2. For decoration
  3. For tax only
  4. For advertising
Show answer & solution

Answer: (A) For safe planning, avoiding old workings, staying within boundaries and use in emergencies

Inspectors examine mine plans during inspections.

Question 7

What does an isopach map show?

  1. Lines of equal ore grade
  2. Lines of equal rainfall
  3. Lines of equal elevation of the surface
  4. Lines of equal thickness of a seam or overburden
Show answer & solution

Answer: (D) Lines of equal thickness of a seam or overburden

Isopachs are used to estimate seam volumes and stripping.

Question 8

What does a structure contour map of a seam show?

  1. Lines of equal elevation of the seam floor or roof
  2. Lines of equal air velocity
  3. Lines of equal thickness
  4. Lines of equal grade
Show answer & solution

Answer: (A) Lines of equal elevation of the seam floor or roof

Structure contours reveal dip, folds and faults.

Question 9

What does an isograde map show?

  1. Lines of equal seam thickness
  2. Lines of equal elevation
  3. Lines of equal ore grade
  4. Lines of equal gradient
Show answer & solution

Answer: (C) Lines of equal ore grade

Isograde maps help in planning selective mining.

Question 10

What is a mine ventilation plan?

  1. A geological map
  2. A plan showing the direction and quantity of airflow and ventilation devices
  3. A plan of the surface buildings
  4. A plan of haul roads only
Show answer & solution

Answer: (B) A plan showing the direction and quantity of airflow and ventilation devices

Ventilation plans show fans, doors, stoppings and airways.

Question 11

What is the relation between the radius R in metres and the degree of a curve D defined on a 30 m arc?

  1. R ≈ 30/D
  2. R ≈ D/1719
  3. R ≈ 5730 × D
  4. R ≈ 1719/D
Show answer & solution

Answer: (D) R ≈ 1719/D

For a 30 m arc, R = 30 × 180/(πD) ≈ 1719/D.

Question 12

What is the length of a circular curve with radius R and deflection angle Δ in degrees?

  1. 2RΔ
  2. πRΔ/180
  3. πR²Δ
  4. R tan Δ
Show answer & solution

Answer: (B) πRΔ/180

Curve length is the arc subtending angle Δ.

Question 13

What is the tangent length of a simple circular curve with radius R and deflection angle Δ?

  1. 2R tan Δ
  2. R cos(Δ/2)
  3. R tan(Δ/2)
  4. R sin Δ
Show answer & solution

Answer: (C) R tan(Δ/2)

It is the distance from the intersection point to each tangent point.

Question 14

What is the tangent length of a curve with a radius of 100 m and a deflection angle of 60°?

  1. 57.7 m
  2. 86.6 m
  3. 100 m
  4. 173.2 m
Show answer & solution

Answer: (A) 57.7 m

T = 100 × tan 30° = 57.7 m.

Question 15

What is the length of a curve with a radius of 100 m and a deflection angle of 90°?

  1. 90.0 m
  2. 100.0 m
  3. 157.1 m
  4. 314.2 m
Show answer & solution

Answer: (C) 157.1 m

L = π × 100 × 90/180 = 157.1 m.

Question 16

What is the purpose of a transition curve?

  1. To join two parallel roads
  2. To replace all circular curves
  3. To make a curve sharper
  4. To change curvature gradually between a straight and a circular curve
Show answer & solution

Answer: (D) To change curvature gradually between a straight and a circular curve

Transition curves let superelevation be introduced smoothly.

Question 17

What is a compound curve?

  1. A straight line
  2. Two or more circular arcs of different radii curving in the same direction
  3. A vertical curve only
  4. Two arcs curving in opposite directions
Show answer & solution

Answer: (B) Two or more circular arcs of different radii curving in the same direction

Compound curves fit difficult ground.

Question 18

What is a reverse curve?

  1. Two circular arcs curving in opposite directions with a common tangent point
  2. Two arcs curving in the same direction
  3. A single arc
  4. A straight road
Show answer & solution

Answer: (A) Two circular arcs curving in opposite directions with a common tangent point

Reverse curves are avoided on fast haul roads.

Question 19

What is the point where a circular curve begins on the first tangent called?

  1. Apex
  2. Point of tangency at the end
  3. Point of intersection
  4. Point of curvature (tangent point)
Show answer & solution

Answer: (D) Point of curvature (tangent point)

The curve ends at the point of tangency.

Question 20

Which method sets out a circular curve using deflection angles with a theodolite and a tape?

  1. Simpson's method
  2. Bowditch's method
  3. Weisbach's method
  4. Rankine's method
Show answer & solution

Answer: (D) Rankine's method

Each chord is set out from the tangent by its deflection angle.

Question 21

What is the mid-ordinate of a circular curve of radius R and deflection angle Δ?

  1. R(1 − cos(Δ/2))
  2. 2R
  3. R tan(Δ/2)
  4. R sin Δ
Show answer & solution

Answer: (A) R(1 − cos(Δ/2))

It is the distance from the middle of the long chord to the curve.

Question 22

Which formula gives the most accurate volume of earthwork between cross-sections?

  1. Bowditch rule
  2. Average end area formula
  3. Prismoidal formula
  4. Simpson's rule for areas only
Show answer & solution

Answer: (C) Prismoidal formula

The prismoidal formula uses the middle section area as well.

Question 23

What is the average end area method for volume?

  1. Volume = L × A1 × A2
  2. Volume = L × (A1 + A2)/2
  3. Volume = (A1 − A2)/L
  4. Volume = L/(A1 + A2)
Show answer & solution

Answer: (B) Volume = L × (A1 + A2)/2

It slightly overestimates volume for pyramid-shaped solids.

Question 24

What is the volume between two sections of area 20 m² and 30 m² that are 10 m apart, by the average end area method?

  1. 50 m³
  2. 250 m³
  3. 500 m³
  4. 2,500 m³
Show answer & solution

Answer: (B) 250 m³

10 × (20 + 30)/2 = 250 m³.

Question 25

Which instrument measures the area of a figure on a plan by tracing its outline?

  1. Pantograph
  2. Clinometer
  3. Planimeter
  4. Theodolite
Show answer & solution

Answer: (C) Planimeter

Digital planimeters give the area directly.

Question 26

What condition does Simpson's rule require for calculating area from ordinates?

  1. An even number of ordinates
  2. Only two ordinates
  3. Unequal intervals
  4. An odd number of ordinates (even number of intervals)
Show answer & solution

Answer: (D) An odd number of ordinates (even number of intervals)

Simpson's rule assumes parabolic boundaries between ordinates.

Question 27

Why must mine plans show the mining lease boundaries?

  1. To ensure that mining stays within the lease area
  2. To show wages
  3. To mark ventilation doors
  4. To show weather
Show answer & solution

Answer: (A) To ensure that mining stays within the lease area

Working beyond lease boundaries is illegal and dangerous near adjoining mines.

Question 28

What is the gradient between two contours 5 m apart in elevation and 100 m apart horizontally?

  1. 1 in 20
  2. 1 in 5
  3. 1 in 50
  4. 1 in 500
Show answer & solution

Answer: (A) 1 in 20

100/5 = 20.

Question 29

What is a geological section in mine planning?

  1. A ventilation diagram
  2. A vertical cross-section showing rock layers, seams and structures
  3. A plan view of the surface
  4. A list of drill holes
Show answer & solution

Answer: (B) A vertical cross-section showing rock layers, seams and structures

Sections are drawn from borehole and mapping data.

Question 30

What does a fault shown on a mine plan represent?

  1. A ventilation door
  2. A drainage line
  3. A survey error
  4. A fracture along which the strata have been displaced
Show answer & solution

Answer: (D) A fracture along which the strata have been displaced

Faults displace seams and must be shown for planning.

Question 31

Why are mine plans and sections prepared at a fixed scale?

  1. For decoration only
  2. To reduce paper
  3. So that distances and areas can be measured accurately from them
  4. So that no measurements are needed
Show answer & solution

Answer: (C) So that distances and areas can be measured accurately from them

Scaled plans allow planning, measurement and legal use.

Question 32

What does a hachure or contour pattern on a plan show?

  1. The shape and slope of the ground surface
  2. Explosive storage
  3. Ore grade
  4. Underground ventilation flow
Show answer & solution

Answer: (A) The shape and slope of the ground surface

Contours are the standard way to show relief.

Question 33

Which digital product is now commonly used to calculate pit and dump volumes?

  1. Hand-drawn sketches
  2. Wage sheets
  3. Digital terrain (surface) models compared between surveys
  4. Ventilation plans
Show answer & solution

Answer: (C) Digital terrain (surface) models compared between surveys

Software subtracts surfaces to find cut and fill volumes.

Practice these 33 questions interactively →