Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Surface Mining: Waste Dumps and Haul Roads

Mining Engineering · Surface Mining

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is a waste dump?

  1. A tailings pond
  2. A stockpile of high-grade ore
  3. A fuel store
  4. An area where overburden and waste rock are placed
Show answer & solution

Answer: (D) An area where overburden and waste rock are placed

Dumps must be designed for stability and drainage.

Question 2

Which dump construction method places waste by trucks tipping over the dump crest?

  1. Conveyor stacking
  2. Layered dumping with compaction
  3. End-tipping (crest) dumping
  4. Paddock dumping
Show answer & solution

Answer: (C) End-tipping (crest) dumping

End-tipping is fast but forms loose slopes at the angle of repose.

Question 3

Which dump construction method spreads waste in thin compacted layers, giving higher stability?

  1. Valley tipping from height
  2. Layered (bottom-up) dumping
  3. Random dumping
  4. End-tipping from the crest
Show answer & solution

Answer: (B) Layered (bottom-up) dumping

Thin lifts compacted by truck traffic give denser, more stable dumps.

Question 4

Which dumping method causes coarse rock to roll to the base, segregating the material?

  1. End-tipping
  2. Layered dumping
  3. Conveyor spreading
  4. Paddock dumping
Show answer & solution

Answer: (A) End-tipping

Segregation in end-tipped dumps forms a coarse base layer.

Question 5

Why is a safety berm (windrow) built along the crest of a dump?

  1. To stop trucks from reversing over the edge
  2. To increase dump height
  3. To store topsoil
  4. To drain water
Show answer & solution

Answer: (A) To stop trucks from reversing over the edge

The berm gives a physical stop and a visual guide.

Question 6

What minimum height is generally recommended for a safety berm at a dump edge?

  1. One brick high
  2. At least the mid-axle height of the largest vehicle
  3. There is no minimum
  4. Twice the truck height
Show answer & solution

Answer: (B) At least the mid-axle height of the largest vehicle

Mine safety rules commonly require berms at least half the wheel height.

Question 7

What are the most common causes of waste dump failure?

  1. Dark coloured rock
  2. Low dump height
  3. Dry weather
  4. Weak foundation soils and high water pressure
Show answer & solution

Answer: (D) Weak foundation soils and high water pressure

Saturated foundations and poor drainage cause most dump slides.

Question 8

What is a dump placed in the mined-out part of the pit called?

  1. Tailings dam
  2. Out-of-pit dump
  3. In-pit (backfill) dump
  4. Valley fill
Show answer & solution

Answer: (C) In-pit (backfill) dump

In-pit dumping is common in strip mines and multi-pit operations.

Question 9

What is the main advantage of in-pit dumping?

  1. Longer hauls
  2. It blocks the ore
  3. Shorter hauls and less land disturbance
  4. More land is disturbed
Show answer & solution

Answer: (C) Shorter hauls and less land disturbance

Waste is placed close to where it is mined.

Question 10

What is acid mine drainage?

  1. Drinking water from boreholes
  2. Acidic water formed by oxidation of sulphide minerals in mine waste
  3. Fresh rainwater
  4. Alkaline water from limestone
Show answer & solution

Answer: (B) Acidic water formed by oxidation of sulphide minerals in mine waste

Acid drainage dissolves metals and harms rivers.

Question 11

Which mineral is mainly responsible for acid mine drainage?

  1. Pyrite
  2. Calcite
  3. Halite
  4. Quartz
Show answer & solution

Answer: (A) Pyrite

Pyrite (FeS₂) oxidises to sulphuric acid and iron hydroxide.

Question 12

What is a common method of preventing acid drainage from waste dumps?

  1. Leaving the waste exposed
  2. Spraying the dump with salt water
  3. Increasing dump height
  4. Covering or encapsulating sulphide waste to exclude oxygen and water
Show answer & solution

Answer: (D) Covering or encapsulating sulphide waste to exclude oxygen and water

Dry covers, water covers and limestone addition are used.

Question 13

What is a tailings dam?

  1. A topsoil stockpile
  2. A dam for drinking water
  3. A haul road embankment
  4. A structure that stores fine waste from mineral processing
Show answer & solution

Answer: (D) A structure that stores fine waste from mineral processing

Tailings are pumped as slurry into the dam.

Question 14

In which tailings dam construction method is the crest raised towards the pond over previously deposited tailings?

  1. Downstream method
  2. Upstream method
  3. Centreline method
  4. Water-retention method
Show answer & solution

Answer: (B) Upstream method

The upstream method is cheapest but builds on loose tailings.

Question 15

Which tailings dam construction method is most vulnerable to earthquake liquefaction?

  1. Upstream method
  2. Concrete gravity dam
  3. Centreline method
  4. Downstream method
Show answer & solution

Answer: (A) Upstream method

Several major tailings failures, such as Brumadinho (2019), involved upstream dams.

Question 16

Which tailings dam construction method is generally the most stable?

  1. Upstream method
  2. Simple end-tipped embankment
  3. Downstream method
  4. Centreline method on loose tailings
Show answer & solution

Answer: (C) Downstream method

Downstream raises are built on compacted fill, not on tailings.

Question 17

What is reclamation in surface mining?

  1. Re-opening old mines
  2. Building new haul roads
  3. Restoring mined land to a stable and productive after-use
  4. Increasing pit depth
Show answer & solution

Answer: (C) Restoring mined land to a stable and productive after-use

Reclamation includes reshaping, topsoiling and re-vegetation.

Question 18

What is the typical maximum sustained grade for open pit haul ramps?

  1. 1 to 2%
  2. 8 to 10%
  3. 20 to 25%
  4. 35 to 40%
Show answer & solution

Answer: (B) 8 to 10%

Most pits design ramps at about 8–10% for loaded trucks.

Question 19

What minimum width is generally recommended for a two-way haul road?

  1. About 1.5 times the truck width
  2. About 2 times the truck width
  3. About 3.5 times the width of the widest truck
  4. About 6 times the truck width
Show answer & solution

Answer: (C) About 3.5 times the width of the widest truck

This allows two trucks to pass with clearance and room for berms and drains.

Question 20

What minimum width is generally recommended for a one-way haul road?

  1. About 1 times the truck width
  2. About 2 times the width of the widest truck
  3. About 3.5 times the truck width
  4. About 6 times the truck width
Show answer & solution

Answer: (B) About 2 times the width of the widest truck

One-way roads need room for the truck, clearances, berm and drain.

Question 21

What is superelevation on a haul road?

  1. Banking of the road on curves to counter centrifugal force
  2. A steeper ramp section
  3. Speed bumps
  4. Raising the road above the pit
Show answer & solution

Answer: (A) Banking of the road on curves to counter centrifugal force

Superelevation lets trucks round curves safely at design speed.

Question 22

What is cross-fall (camber) on a haul road?

  1. Slope along the road
  2. A safety berm
  3. A sharp bend
  4. Slope across the road to drain water
Show answer & solution

Answer: (D) Slope across the road to drain water

Cross-fall prevents water ponding on the running surface.

Question 23

What cross-fall is typically used on haul roads?

  1. 0%
  2. About 2%
  3. About 10%
  4. About 25%
Show answer & solution

Answer: (B) About 2%

About 2–3% drains water without making trucks slide sideways.

Question 24

Why are haul roads sprayed with water?

  1. To suppress dust
  2. To increase rolling resistance
  3. To cool truck tyres only
  4. To mark the road edge
Show answer & solution

Answer: (A) To suppress dust

Dust reduces visibility and harms health.

Question 25

What is the main cause of high rolling resistance on haul roads?

  1. A smooth compacted surface
  2. Proper cross-fall
  3. Dry weather
  4. A poor surface with ruts and soft material
Show answer & solution

Answer: (D) A poor surface with ruts and soft material

Soft, rutted roads can raise rolling resistance from 2% to over 5%.

Question 26

Which haul road layers spread wheel loads down to the subgrade?

  1. Wearing course only
  2. Safety berm
  3. Drainage ditch
  4. Base and sub-base layers
Show answer & solution

Answer: (D) Base and sub-base layers

Thickness of base layers depends on wheel load and subgrade strength.

Question 27

What is the wearing course of a haul road?

  1. The top surface layer that gives traction and resists wear
  2. The drainage ditch
  3. The bottom subgrade
  4. The safety berm
Show answer & solution

Answer: (A) The top surface layer that gives traction and resists wear

Good wearing course material is well graded gravel or crushed rock.

Question 28

Which method designs haul road layer thickness from the California Bearing Ratio of the subgrade?

  1. Q-system method
  2. Kriging method
  3. CBR cover-curve method
  4. RMR method
Show answer & solution

Answer: (C) CBR cover-curve method

Weaker subgrade (lower CBR) needs a thicker cover of base material.

Question 29

What is a runaway (arrester) lane on a haul road?

  1. A lane for light vehicles
  2. A passing lane
  3. A parking bay
  4. An escape lane with soft material to stop a truck that loses its brakes
Show answer & solution

Answer: (D) An escape lane with soft material to stop a truck that loses its brakes

Arrester beds of loose gravel stop out-of-control trucks.

Question 30

Why is a median berm sometimes placed along steep haul ramps?

  1. To separate ore and waste
  2. So that a runaway truck can straddle it and be stopped
  3. To improve drainage only
  4. To store topsoil
Show answer & solution

Answer: (B) So that a runaway truck can straddle it and be stopped

Driving onto the berm lifts the truck and slows it.

Question 31

What is the basic sight distance requirement on a haul road?

  1. Stopping sight distance must exceed the truck's braking distance
  2. Sight distance matters only at night
  3. Sight distance must equal the truck length
  4. Drivers need no sight distance
Show answer & solution

Answer: (A) Stopping sight distance must exceed the truck's braking distance

Curves and crests must let drivers see hazards in time to stop.

Question 32

How does increasing ramp grade affect loaded truck speed?

  1. It increases speed
  2. It has no effect
  3. It reduces speed and productivity
  4. It reduces fuel use
Show answer & solution

Answer: (C) It reduces speed and productivity

Steeper grades require lower gears and slower speeds.

Question 33

What is a dump lift?

  1. A lift used to raise trucks
  2. The topsoil layer
  3. A layer of a waste dump of a given height
  4. A crane at the dump
Show answer & solution

Answer: (C) A layer of a waste dump of a given height

Dumps are built in lifts with berms between them.

Question 34

Why should dumps not be built over springs or drainage lines without under-drainage?

  1. It makes hauling shorter
  2. Water saturation reduces dump stability
  3. It increases dump height
  4. Water improves stability
Show answer & solution

Answer: (B) Water saturation reduces dump stability

Water pressure in the base can trigger flow slides.

Question 35

What is a dump built across a valley, often with an under-drain, called?

  1. In-pit dump
  2. Tailings dam
  3. Heaped dump on flat ground
  4. Valley fill dump
Show answer & solution

Answer: (D) Valley fill dump

Valley fills are common in hilly terrain.

Question 36

What are rock drains (French drains) under valley fill dumps?

  1. Coarse rock channels that let water flow beneath the dump
  2. Electric cables
  3. Haul road ditches
  4. Pipes for compressed air
Show answer & solution

Answer: (A) Coarse rock channels that let water flow beneath the dump

Rock drains carry stream water through the base of the dump.

Question 37

What is the main purpose of a toe drain at the base of a waste dump?

  1. To remove seepage water and keep the dump base dry
  2. To mark the haul road
  3. To hold explosives
  4. To store fuel
Show answer & solution

Answer: (A) To remove seepage water and keep the dump base dry

Removing water from the base improves dump stability.

Practice these 37 questions interactively →