Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Surface Mining: Loading and Hauling

Mining Engineering · Surface Mining

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which loading machine with a front-mounted dipper on wire ropes is used for loading trucks in large open pits?

  1. Bulldozer
  2. Dragline
  3. Electric rope shovel
  4. Scraper
Show answer & solution

Answer: (C) Electric rope shovel

Rope shovels have dippers of up to about 80 m³.

Question 2

Which hydraulic excavator configuration digs by pulling the bucket towards the machine, suiting loading from below its own level?

  1. Backhoe
  2. Bucket wheel
  3. Front shovel
  4. Dragline
Show answer & solution

Answer: (A) Backhoe

The backhoe sits on the bench top and digs downward.

Question 3

Which excavator configuration digs by pushing the bucket upward and away from the machine?

  1. Clamshell
  2. Front shovel
  3. Backhoe
  4. Dragline
Show answer & solution

Answer: (B) Front shovel

Front shovels dig a face above their track level.

Question 4

Which excavator uses a bucket hung from a boom by ropes and dragged towards the machine?

  1. Backhoe
  2. Wheel loader
  3. Front shovel
  4. Dragline
Show answer & solution

Answer: (D) Dragline

Draglines have long reach and are used for overburden in strip mines.

Question 5

Which continuous excavator with a rotating wheel of buckets is used in soft overburden and lignite?

  1. Bucket wheel excavator
  2. Rope shovel
  3. LHD
  4. Dragline
Show answer & solution

Answer: (A) Bucket wheel excavator

Bucket wheel excavators feed conveyors continuously.

Question 6

Which mobile machine loads trucks and can also carry material short distances on tyres?

  1. Bucket wheel excavator
  2. Rope shovel
  3. Wheel (front-end) loader
  4. Dragline
Show answer & solution

Answer: (C) Wheel (front-end) loader

Wheel loaders are flexible and quick to move between faces.

Question 7

Which machine loads, hauls and dumps material itself over moderate distances in soft ground?

  1. Motor grader
  2. Bulldozer
  3. Rope shovel
  4. Scraper
Show answer & solution

Answer: (D) Scraper

Scrapers are used for topsoil and soft overburden removal.

Question 8

What is the main use of a bulldozer in surface mines?

  1. Hauling ore long distances
  2. Pushing material, ripping, shaping dumps and clean-up
  3. Loading trucks
  4. Drilling blast holes
Show answer & solution

Answer: (B) Pushing material, ripping, shaping dumps and clean-up

Dozers are support equipment in most surface mines.

Question 9

Which machine is used to maintain and shape the surface of haul roads?

  1. Motor grader
  2. Scraper
  3. Rope shovel
  4. Bulldozer
Show answer & solution

Answer: (A) Motor grader

Graders keep roads smooth and maintain cross-fall.

Question 10

What is a ripper in surface mining?

  1. A blasting accessory
  2. A tine mounted on a dozer to break soft rock without blasting
  3. A crushing machine
  4. A type of drill bit
Show answer & solution

Answer: (B) A tine mounted on a dozer to break soft rock without blasting

Ripping is possible where seismic velocity of the rock is low enough.

Question 11

What makes up the cycle time of a haul truck?

  1. Loading time only
  2. Dumping time only
  3. Loading, hauling, dumping, returning, spotting and queuing time
  4. Hauling time only
Show answer & solution

Answer: (C) Loading, hauling, dumping, returning, spotting and queuing time

Truck fleet size depends on total cycle time.

Question 12

What is the formula for match factor, where Nt is number of trucks, Nl number of loaders, tl loading time per truck and tc truck cycle time?

  1. MF = tc/tl
  2. MF = (Nl × tc)/(Nt × tl)
  3. MF = Nt × Nl
  4. MF = (Nt × tl)/(Nl × tc)
Show answer & solution

Answer: (D) MF = (Nt × tl)/(Nl × tc)

Match factor compares truck arrival rate with loader service rate.

Question 13

What does a match factor of 1 indicate in a shovel–truck system?

  1. There are too many trucks
  2. The loader is broken
  3. There are too few trucks
  4. The truck fleet and loaders are balanced
Show answer & solution

Answer: (D) The truck fleet and loaders are balanced

At MF = 1, neither trucks nor loaders wait in theory.

Question 14

What does a match factor less than 1 indicate?

  1. Too few trucks, so the loader waits
  2. Too many trucks, so trucks queue
  3. The fleet is balanced
  4. The loader has no work at all because of breakdown
Show answer & solution

Answer: (A) Too few trucks, so the loader waits

Low match factor wastes loader capacity.

Question 15

What does a match factor greater than 1 indicate?

  1. There is no loader
  2. The fleet is balanced
  3. Trucks queue and wait at the loader
  4. The loader waits for trucks
Show answer & solution

Answer: (C) Trucks queue and wait at the loader

High match factor means truck time is lost in queues.

Question 16

How many bucket passes should ideally fill a haul truck?

  1. 1
  2. 3 to 5
  3. 10 to 12
  4. 20
Show answer & solution

Answer: (B) 3 to 5

Matching loader bucket size to truck body so that 3–5 passes fill it gives good productivity.

Question 17

If a shovel cycle is 30 seconds and a truck needs 4 passes, what is the loading time per truck?

  1. 2 minutes
  2. 4 minutes
  3. 8 minutes
  4. 30 seconds
Show answer & solution

Answer: (A) 2 minutes

4 × 30 s = 120 s = 2 minutes.

Question 18

If truck cycle time is 20 minutes and loading time is 4 minutes, how many trucks are needed to keep one shovel fully busy?

  1. 4
  2. 5
  3. 6
  4. 20
Show answer & solution

Answer: (B) 5

Number of trucks = cycle time/loading time = 20/4 = 5.

Question 19

What is rimpull?

  1. Brake force on the wheels
  2. Weight of the truck
  3. Rolling resistance
  4. Tractive force available at the rim of the driving wheels
Show answer & solution

Answer: (D) Tractive force available at the rim of the driving wheels

Rimpull charts show available force at each gear and speed.

Question 20

How is rolling resistance usually expressed for haul trucks?

  1. As fuel consumption
  2. As tyre size
  3. As a percentage of gross vehicle weight (equivalent grade)
  4. As engine power
Show answer & solution

Answer: (C) As a percentage of gross vehicle weight (equivalent grade)

A rolling resistance of 2% acts like a 2% uphill grade.

Question 21

What is total resistance on a haul road?

  1. Rolling resistance minus grade resistance
  2. Rolling resistance plus grade resistance
  3. Air resistance only
  4. Grade resistance only
Show answer & solution

Answer: (B) Rolling resistance plus grade resistance

Total resistance is often given as an effective grade.

Question 22

What is the effective grade for a truck climbing an 8% ramp with 2% rolling resistance?

  1. 6%
  2. 8%
  3. 10%
  4. 16%
Show answer & solution

Answer: (C) 10%

Effective grade = 8% + 2% = 10%.

Question 23

Which haul truck type is used in large open pits on well-built haul roads?

  1. Rigid-frame rear-dump truck
  2. Articulated dump truck
  3. Farm tractor and trailer
  4. Bottom-dump coal hauler only
Show answer & solution

Answer: (A) Rigid-frame rear-dump truck

Rigid trucks carry from about 40 t to over 400 t.

Question 24

Which truck type performs better on soft, wet or steep ground?

  1. Rigid-frame truck
  2. Bottom-dump trailer
  3. Road tipper
  4. Articulated dump truck
Show answer & solution

Answer: (D) Articulated dump truck

Articulation and all-wheel drive give better traction off-road.

Question 25

Which system on large haul trucks slows the truck on downhill grades without wearing the service brakes?

  1. Parking brake
  2. Handbrake
  3. Drum brake only
  4. Electric (dynamic) retarder
Show answer & solution

Answer: (D) Electric (dynamic) retarder

The traction motors act as generators and the energy is dissipated in grids.

Question 26

What drive system do most large mining trucks above about 200 tonnes use?

  1. Mechanical gearbox drive
  2. Diesel-electric drive
  3. Hydrostatic drive
  4. Pneumatic drive
Show answer & solution

Answer: (B) Diesel-electric drive

A diesel engine drives a generator that powers wheel motors.

Question 27

Which continuous haulage system moves ore out of deep pits at lower cost than trucks?

  1. Rail haulage by steam locomotive
  2. Aerial ropeway only
  3. In-pit crushing and conveying (IPCC)
  4. Hand carts
Show answer & solution

Answer: (C) In-pit crushing and conveying (IPCC)

IPCC crushes rock in the pit so that belts can carry it out.

Question 28

What is the main advantage of IPCC in deep pits?

  1. Lower operating cost and diesel use for long, deep hauls
  2. No need for crushing
  3. Higher flexibility than trucks
  4. No capital cost
Show answer & solution

Answer: (A) Lower operating cost and diesel use for long, deep hauls

Conveyors climb steep grades efficiently.

Question 29

What is spotting in shovel–truck operation?

  1. Weighing the truck
  2. Fuelling the truck
  3. Dumping the load
  4. Positioning the truck under the loading bucket
Show answer & solution

Answer: (D) Positioning the truck under the loading bucket

Fast spotting reduces loader idle time.

Question 30

What is double-side loading?

  1. Trucks positioned on both sides of the loader so one spots while the other is loaded
  2. Loading on two benches at once
  3. Loading two trucks with one bucket
  4. Loading both ore and waste together
Show answer & solution

Answer: (A) Trucks positioned on both sides of the loader so one spots while the other is loaded

It cuts loader waiting time during truck exchange.

Question 31

What is the fill factor of a bucket?

  1. Ratio of truck payload to bucket size
  2. Ratio of actual loose volume in the bucket to its rated capacity
  3. Ratio of ore to waste
  4. Ratio of bank to loose volume
Show answer & solution

Answer: (B) Ratio of actual loose volume in the bucket to its rated capacity

Fill factor depends on fragmentation and digging conditions.

Question 32

What is the mechanical availability of mining equipment?

  1. The age of the machine
  2. The engine power
  3. The proportion of time the equipment is mechanically fit to work
  4. The proportion of time it actually works
Show answer & solution

Answer: (C) The proportion of time the equipment is mechanically fit to work

Availability excludes time spent under repair and maintenance.

Question 33

What is equipment utilisation?

  1. The machine's weight
  2. The proportion of time under repair
  3. The proportion of available time the equipment actually works
  4. The fuel used per hour
Show answer & solution

Answer: (C) The proportion of available time the equipment actually works

Low utilisation shows poor planning or waiting.

Question 34

Which technology assigns trucks to loaders automatically to reduce waiting?

  1. Ventilation system
  2. Pumping system
  3. Blasting system
  4. Fleet management (truck dispatch) system
Show answer & solution

Answer: (D) Fleet management (truck dispatch) system

Dispatch systems use GPS and algorithms to route trucks in real time.

Question 35

What is the payload of a haul truck?

  1. The engine power
  2. The mass of material carried per trip
  3. The empty weight of the truck
  4. The fuel tank capacity
Show answer & solution

Answer: (B) The mass of material carried per trip

Payload monitoring avoids overloading and tyre damage.

Question 36

Which haul road factor most strongly affects loaded truck speed and fuel use on ramps?

  1. Ramp gradient
  2. Driver age
  3. Radio type
  4. Truck colour
Show answer & solution

Answer: (A) Ramp gradient

Steeper ramps reduce speed and increase fuel consumption.

Question 37

What is an autonomous haulage system?

  1. Trucks driven by two drivers
  2. Conveyors without belts
  3. A fleet of driverless haul trucks controlled by computer
  4. Trucks with manual gearboxes
Show answer & solution

Answer: (C) A fleet of driverless haul trucks controlled by computer

Autonomous trucks run on GPS and sensors under central control.

Question 38

Which truck feature is used to weigh each load automatically during loading?

  1. Onboard payload monitoring system
  2. Tipping hoist
  3. Rear-view mirror
  4. Engine retarder
Show answer & solution

Answer: (A) Onboard payload monitoring system

Payload systems prevent overloading and record production.

Question 39

What is truck queuing time at a loader caused by?

  1. Long dumping time only
  2. More trucks arriving than the loader can serve
  3. Too few trucks
  4. Short haul roads only
Show answer & solution

Answer: (B) More trucks arriving than the loader can serve

Queuing occurs when the match factor is greater than 1.

Practice these 39 questions interactively →