Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Surface Mining: Drilling Equipment

Mining Engineering · Surface Mining

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which drilling method is most widely used for large-diameter blast holes in big open pits?

  1. Diamond core drilling
  2. Hand-held jackhammer drilling
  3. Auger drilling by hand
  4. Rotary drilling with tricone bits
Show answer & solution

Answer: (D) Rotary drilling with tricone bits

Large electric or diesel rotary rigs drill holes of about 200–311 mm.

Question 2

In which drilling method does a hammer at the bottom of the hole strike the bit directly?

  1. Rotary drilling
  2. Down-the-hole (DTH) drilling
  3. Top-hammer drilling
  4. Diamond drilling
Show answer & solution

Answer: (B) Down-the-hole (DTH) drilling

The DTH hammer follows the bit into the hole, so energy loss is small.

Question 3

In which drilling method is the percussive blow delivered by a hammer at the top of the drill string?

  1. Top-hammer drilling
  2. Rotary drilling
  3. Auger drilling
  4. DTH drilling
Show answer & solution

Answer: (A) Top-hammer drilling

The impact travels down the rods to the bit.

Question 4

What is the main drawback of top-hammer drilling for deep holes?

  1. It produces core samples
  2. It cannot drill hard rock
  3. Energy loss through rod joints and increasing hole deviation
  4. It needs no flushing
Show answer & solution

Answer: (C) Energy loss through rod joints and increasing hole deviation

Each rod joint absorbs energy and the rods bend more as depth increases.

Question 5

What is a tricone bit?

  1. A cutting tool for coal
  2. A rotary bit with three rotating toothed or button cones
  3. A bit used only for augers
  4. A bit with three diamond crowns
Show answer & solution

Answer: (B) A rotary bit with three rotating toothed or button cones

The cones crush and chip rock as the bit rotates under pull-down force.

Question 6

Which drilling method gives solid core samples for exploration and geotechnical logging?

  1. Tricone rotary drilling
  2. Auger drilling
  3. Diamond core drilling
  4. DTH drilling
Show answer & solution

Answer: (C) Diamond core drilling

A diamond-impregnated crown cuts an annulus and the core is recovered in a core barrel.

Question 7

Which drilling method cuts by shearing and is used in soft formations such as coal and clay?

  1. Diamond drilling
  2. Top-hammer drilling
  3. DTH drilling
  4. Rotary drag-bit drilling
Show answer & solution

Answer: (D) Rotary drag-bit drilling

Drag bits scrape soft rock with fixed cutting blades.

Question 8

What is the function of compressed air in blast hole drilling?

  1. To flush cuttings out of the hole and cool the bit
  2. To measure the hole depth
  3. To power the truck
  4. To fire the explosive
Show answer & solution

Answer: (A) To flush cuttings out of the hole and cool the bit

Adequate up-hole air velocity is needed to lift cuttings.

Question 9

What is the main effect of insufficient flushing in drilling?

  1. Regrinding of cuttings and a slower penetration rate
  2. Better hole straightness
  3. A faster penetration rate
  4. Longer bit life
Show answer & solution

Answer: (A) Regrinding of cuttings and a slower penetration rate

Cuttings left at the bottom are crushed again, wasting energy.

Question 10

What does the penetration rate of a drill mean?

  1. Number of holes per shift
  2. Depth drilled per unit time
  3. Diameter of the hole
  4. Weight of the drill
Show answer & solution

Answer: (B) Depth drilled per unit time

Penetration rate is usually given in metres per hour.

Question 11

Which rock properties most affect drill penetration rate and bit wear?

  1. Colour and lustre
  2. Porosity alone
  3. Permeability alone
  4. Hardness and abrasiveness
Show answer & solution

Answer: (D) Hardness and abrasiveness

Hard, abrasive (quartz-rich) rock slows drilling and wears bits.

Question 12

What is sub-drilling?

  1. Drilling horizontal holes
  2. Drilling for exploration
  3. Drilling below the planned floor level to avoid leaving a toe
  4. Drilling a short hole above the floor
Show answer & solution

Answer: (C) Drilling below the planned floor level to avoid leaving a toe

Sub-drill gives full breakage at grade level.

Question 13

About how much sub-drilling is commonly used in bench blasting?

  1. About 0.05 times the burden
  2. About 0.3 times the burden
  3. About 3 times the burden
  4. About 10 times the burden
Show answer & solution

Answer: (B) About 0.3 times the burden

Sub-drilling of roughly 0.3B is a common rule of thumb.

Question 14

What is the collar of a drill hole?

  1. The rod coupling
  2. The bottom of the hole
  3. The drill bit
  4. The top opening of the hole at the surface
Show answer & solution

Answer: (D) The top opening of the hole at the surface

Stemming is placed in the collar zone of a loaded hole.

Question 15

What is hole deviation in drilling?

  1. Departure of a drilled hole from its planned direction
  2. The planned angle of the hole
  3. Diameter variation along the hole
  4. Depth of sub-drilling
Show answer & solution

Answer: (A) Departure of a drilled hole from its planned direction

Deviation spoils the blast pattern and can cause flyrock or toes.

Question 16

Which drill uses a rotating helical screw to bring cuttings out of a hole in soft ground?

  1. DTH drill
  2. Diamond drill
  3. Auger drill
  4. Top-hammer drill
Show answer & solution

Answer: (C) Auger drill

Augers are used in soil, clay, soft coal and overburden.

Question 17

What is the purpose of a dust collector on a blast hole drill?

  1. To capture dust from the flushing air
  2. To cool the engine
  3. To measure hole depth
  4. To store explosives
Show answer & solution

Answer: (A) To capture dust from the flushing air

Dust collection protects drillers from respirable silica dust.

Question 18

Which bit type is most common in DTH and top-hammer percussive drilling?

  1. Drag bit
  2. Tricone bit
  3. Button bit
  4. Diamond crown
Show answer & solution

Answer: (C) Button bit

Tungsten carbide buttons crush rock under impact.

Question 19

What is bit regrinding?

  1. Replacing drill rods
  2. Cleaning the dust collector
  3. Repairing the drill engine
  4. Sharpening worn button or insert bits to restore their shape
Show answer & solution

Answer: (D) Sharpening worn button or insert bits to restore their shape

Regular regrinding keeps penetration rate high and extends bit life.

Question 20

What is pull-down force on a rotary drill?

  1. The upward force on the rods
  2. The downward thrust applied to the bit
  3. The air pressure
  4. The torque on the engine
Show answer & solution

Answer: (B) The downward thrust applied to the bit

Rotary drilling needs high pull-down to crush rock under the cones.

Question 21

Which two parameters mainly control the penetration rate in rotary drilling?

  1. Truck size and bench height
  2. Pull-down force and rotary speed
  3. Explosive type and stemming
  4. Air temperature and humidity
Show answer & solution

Answer: (B) Pull-down force and rotary speed

Penetration increases with weight on bit and rotation speed up to a limit.

Question 22

Which percussive method gives straighter holes in hard rock open pit drilling?

  1. Auger drilling
  2. Top-hammer drilling
  3. DTH drilling
  4. Hand jackhammer drilling
Show answer & solution

Answer: (C) DTH drilling

The DTH hammer is close behind the bit, which keeps the hole straight.

Question 23

What is a jackhammer?

  1. A hand-held pneumatic percussive rock drill
  2. A raise boring machine
  3. A large rotary drill
  4. A hydraulic excavator
Show answer & solution

Answer: (A) A hand-held pneumatic percussive rock drill

Jackhammers are used for small holes in small quarries and secondary breaking.

Question 24

Which drill is commonly used for shallow small-diameter holes in small quarries?

  1. Tunnel boring machine
  2. Raise borer
  3. Large electric rotary drill
  4. Hand-held pneumatic jackhammer
Show answer & solution

Answer: (D) Hand-held pneumatic jackhammer

Small quarries often use compressor-driven hand-held drills.

Question 25

What is the typical hole diameter range drilled by large rotary blast hole rigs in big open pits?

  1. 25 to 38 mm
  2. 51 to 64 mm
  3. 200 to 311 mm
  4. 500 to 600 mm
Show answer & solution

Answer: (C) 200 to 311 mm

Large pits commonly use holes of about 250 mm.

Question 26

In which unit is drilling cost commonly expressed?

  1. Cost per metre drilled
  2. Cost per truck
  3. Cost per worker
  4. Cost per day of rain
Show answer & solution

Answer: (A) Cost per metre drilled

Drilling cost per metre is combined with specific drilling to cost blasting.

Question 27

What is a drill pattern?

  1. The drill's engine size
  2. The hole depth only
  3. The type of drill bit
  4. The layout of burden and spacing of blast holes
Show answer & solution

Answer: (D) The layout of burden and spacing of blast holes

Square and staggered patterns are common.

Question 28

What is the main advantage of inclined (angled) blast holes?

  1. They need more explosive
  2. Better breakage at the toe with less sub-drill and backbreak
  3. They are easier to drill in every case
  4. They increase flyrock
Show answer & solution

Answer: (B) Better breakage at the toe with less sub-drill and backbreak

Inclined holes give a more uniform burden along the hole.

Question 29

What is the function of the mast on a blast hole drill?

  1. To store explosives
  2. To hold and guide the drill string
  3. To collect dust
  4. To carry the operator cab
Show answer & solution

Answer: (B) To hold and guide the drill string

The mast carries the rotary head and feed system.

Question 30

What is the drill rod (drill steel)?

  1. The pipe that transmits thrust, rotation and flushing to the bit
  2. The cable of the mast
  3. The hammer piston
  4. The bit itself
Show answer & solution

Answer: (A) The pipe that transmits thrust, rotation and flushing to the bit

Rods are coupled together as the hole deepens.

Question 31

Which index developed in Norway is used to predict rock drillability?

  1. RMR
  2. RQD
  3. Q-value
  4. Drilling Rate Index (DRI)
Show answer & solution

Answer: (D) Drilling Rate Index (DRI)

DRI combines brittleness and surface hardness tests.

Question 32

What is specific drilling in blast design?

  1. Depth of one hole
  2. Total metres drilled per year
  3. Metres drilled per cubic metre or tonne of rock blasted
  4. Number of rigs per pit
Show answer & solution

Answer: (C) Metres drilled per cubic metre or tonne of rock blasted

Specific drilling links drilling cost to blasted volume.

Question 33

What is bench drilling?

  1. Horizontal holes in a tunnel
  2. Vertical or inclined holes drilled from the top of a bench
  3. Exploration holes from the surface
  4. Holes in a waste dump
Show answer & solution

Answer: (B) Vertical or inclined holes drilled from the top of a bench

Bench drilling prepares blasts for loading at the bench floor.

Question 34

Which occupational disease is the main health risk from dry drilling in quartz-rich rock?

  1. Malaria
  2. Hepatitis
  3. Asthma caused by pollen
  4. Silicosis
Show answer & solution

Answer: (D) Silicosis

Breathing fine crystalline silica causes silicosis.

Question 35

What is wet drilling?

  1. Drilling with water to suppress dust
  2. Drilling under the sea
  3. Drilling in flooded holes only
  4. Drilling with oil
Show answer & solution

Answer: (A) Drilling with water to suppress dust

Water injection or mist binds dust at the source.

Question 36

Which drilling method returns cuttings through an inner tube to avoid contamination and is used for grade control?

  1. Auger drilling
  2. Open-hole DTH drilling
  3. Reverse circulation (RC) drilling
  4. Diamond core drilling
Show answer & solution

Answer: (C) Reverse circulation (RC) drilling

RC drilling gives clean chip samples quickly and cheaply.

Question 37

What does the term "rig productivity" mean in blast hole drilling?

  1. Diameter of the holes
  2. Metres drilled per operating hour
  3. Number of rigs in the pit
  4. Weight of the rig
Show answer & solution

Answer: (B) Metres drilled per operating hour

Productivity depends on penetration rate and time spent moving and setting up.

Question 38

Why are blast holes sometimes lined with plastic casing in soft or broken ground?

  1. To increase hole diameter
  2. To slow down drilling
  3. To cool the bit
  4. To prevent the hole collapsing before charging
Show answer & solution

Answer: (D) To prevent the hole collapsing before charging

Liners keep holes open in broken or wet ground.

Practice these 38 questions interactively →