What is safety fuse?
Show answer & solution
Answer: (C) A cord with a black powder core that burns at a slow, known rate
Safety fuse carries a flame to a plain detonator.
Mining Engineering · Explosives & Blasting
37 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is safety fuse?
Answer: (C) A cord with a black powder core that burns at a slow, known rate
Safety fuse carries a flame to a plain detonator.
What is the standard burning rate of safety fuse?
Answer: (C) About 120 seconds per metre
The rate must be checked for every batch before use.
Which detonator is used with safety fuse?
Answer: (A) Plain detonator
The fuse is inserted into the open end of the plain detonator and crimped.
Why must an approved non-sparking crimper be used to attach a plain detonator to safety fuse?
Answer: (A) To fix the fuse firmly without sparks or impact that could fire the detonator
Crimpers made of non-ferrous metal apply a gentle, even crimp near the open end.
What are the main parts of an electric detonator?
Answer: (D) Leg wires, bridge wire with fusehead, delay element, primary charge and base charge
Current heats the bridge wire, igniting the fusehead.
What is a delay detonator?
Answer: (B) A detonator that fires a set time after the firing signal
Delays let holes fire in sequence.
Which delay detonators are commonly used in underground tunnelling rounds?
Answer: (A) Long-period (half-second) delays
Long delays give time for rock to move out of the confined face.
What is an exploder (blasting machine)?
Answer: (B) A device that supplies electric energy to fire an electric blasting circuit
Exploders deliver a high-energy pulse to fire many detonators.
Which instrument checks the continuity and resistance of an electric blasting circuit?
Answer: (D) Blasting ohmmeter (galvanometer)
Circuit testing before firing detects breaks and short circuits.
What is the total resistance of n identical electric detonators connected in series, each of resistance r?
Answer: (C) n × r
In series the resistances add.
What is the main hazard of electric detonators?
Answer: (D) Accidental firing by extraneous electricity such as stray current, lightning and radio frequency energy
Electric detonators must be kept away from sources of current.
Why are the leg wires of electric detonators shunted?
Answer: (A) To short-circuit the wires and prevent accidental firing by stray currents
The shunt is removed only when connecting into the circuit.
What is a shock tube (NONEL) system?
Answer: (B) A plastic tube with a thin explosive coating that carries a low-energy shock wave to the detonator
The tube transmits the signal without detonating the surrounding explosive.
What is the main advantage of shock tube initiation systems?
Answer: (C) They are immune to stray currents and radio frequency energy
Non-electric systems are safe near power lines and transmitters.
Which company developed the NONEL shock tube system?
Answer: (C) Nitro Nobel of Sweden
NONEL was introduced in the 1970s.
What is detonating cord?
Answer: (A) A flexible cord with a PETN core that detonates at high velocity
It is used for downlines, trunklines and pre-split charges.
What is the typical VOD of detonating cord?
Answer: (C) About 6,500 to 7,000 m/s
The high VOD makes it suitable for nearly simultaneous initiation.
What is a disadvantage of using detonating cord downlines in bulk-loaded holes?
Answer: (D) It causes airblast noise and can disrupt or desensitise the explosive along the hole
Low-energy initiation systems avoid these problems.
What is the main advantage of electronic detonators?
Answer: (B) Very precise programmable delay times
Accurate timing improves fragmentation and vibration control.
Which detonator type gives the most accurate delay timing?
Answer: (D) Electronic detonator
Electronic delays use a timing chip instead of a pyrotechnic element.
What is delay scatter?
Answer: (B) Variation between the actual and nominal firing times of delay detonators
Pyrotechnic delays can scatter by several percent.
What is a surface delay connector in a shock tube system?
Answer: (A) A delay unit connected on the surface between holes to set firing sequence
Surface connectors allow flexible timing patterns.
Why is bottom priming generally preferred in bench blasting?
Answer: (A) It gives better breakage at the toe and reduces flyrock and stemming ejection
Detonation travels upward, with gas held by the stemming.
Why is a booster used to initiate ANFO?
Answer: (C) ANFO is not cap-sensitive and needs strong initiation
A cast booster ensures full-strength detonation at once.
What is the firing line (lead wire) in electric blasting?
Answer: (D) The cable connecting the blasting circuit to the exploder at a safe position
The firing line is kept short-circuited until firing.
Which electric blasting circuit is used for a large number of detonators so that the current is shared among branches?
Answer: (B) Parallel or series-in-parallel circuit
Large blasts need series-in-parallel circuits with balanced resistance.
What happens in a series electric blasting circuit if there is one break?
Answer: (A) No detonator in the circuit fires
A series circuit needs a continuous path for current.
What is igniter cord used for?
Answer: (D) Lighting several safety fuses in sequence
Igniter cord burns along its length and lights fuses attached to it.
Why is the burning rate of each batch of safety fuse tested before use?
Answer: (C) To ensure the shotfirer has enough time to reach a safe place
Burning rates can vary and must be posted at the mine.
What type of exploder must be used for firing shots in a gassy coal mine?
Answer: (B) An approved flameproof exploder
Flameproof exploders will not ignite methane.
What inter-row delay is commonly recommended in surface bench blasting?
Answer: (D) About 6 to 12 ms per metre of burden
This allows the front row to move before the next row fires.
Why are delay detonators used in multi-hole blasts?
Answer: (A) To give relief to each hole and limit the charge fired at one instant
Delays improve fragmentation and reduce vibration and airblast.
What is cut-off in blasting?
Answer: (C) Failure of a charge because ground movement from an earlier hole cuts its initiation line
Cut-offs cause misfires and flyrock risk.
Why are mobile phones and radio transmitters restricted near electric blasting circuits?
Answer: (B) Radio frequency energy can induce current in the circuit
Safe distances from transmitters are specified in blasting rules.
What should be done when a thunderstorm approaches a site with charged holes?
Answer: (C) Stop work and clear everyone from the blast area
Lightning can initiate electric and even non-electric systems.
What is the main purpose of a trunkline in a surface blasting pattern?
Answer: (D) To carry the initiation signal along the rows to each hole's downline
Trunklines can be detonating cord or shock tube with connectors.
What is a downline in blasting?
Answer: (A) The line carrying the initiation signal from the surface down to the primer in the hole
Downlines may be shock tube, detonating cord or electric leg wires.