Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Explosives & Blasting: Explosive Properties

Mining Engineering · Explosives & Blasting

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does VOD stand for in blasting?

  1. Velocity of detonation
  2. Volume of detonation
  3. Velocity of drilling
  4. Value of density
Show answer & solution

Answer: (A) Velocity of detonation

VOD is the speed at which the detonation front travels through the explosive.

Question 2

What is the typical VOD of ANFO in large-diameter holes?

  1. About 50 m/s
  2. About 300 m/s
  3. About 3,000 to 4,500 m/s
  4. About 10,000 m/s
Show answer & solution

Answer: (C) About 3,000 to 4,500 m/s

ANFO VOD depends strongly on hole diameter and confinement.

Question 3

Which classical method measures VOD by comparing the explosive with detonating cord of known velocity?

  1. Ballistic mortar test
  2. Dautriche method
  3. Trauzl lead block test
  4. Gap test
Show answer & solution

Answer: (B) Dautriche method

The meeting point of two detonation waves in the cord gives the VOD.

Question 4

How does hole diameter affect the VOD of ANFO?

  1. Diameter has no effect
  2. VOD becomes zero in large holes
  3. VOD decreases with diameter
  4. VOD increases with diameter up to a steady value
Show answer & solution

Answer: (D) VOD increases with diameter up to a steady value

ANFO is a non-ideal explosive with a large reaction zone.

Question 5

What is the critical diameter of an explosive?

  1. The smallest charge diameter at which stable detonation will propagate
  2. The largest hole that can be drilled
  3. The diameter of a detonator
  4. The diameter at which VOD is maximum
Show answer & solution

Answer: (A) The smallest charge diameter at which stable detonation will propagate

Below the critical diameter detonation dies out.

Question 6

Which formula approximates the detonation pressure of an explosive with density ρ and velocity D?

  1. P = 4ρD²
  2. P = ρD²/4
  3. P = D/ρ
  4. P = ρD/4
Show answer & solution

Answer: (B) P = ρD²/4

Detonation pressure rises with the square of VOD.

Question 7

Which pressure mainly heaves and displaces broken rock?

  1. Atmospheric pressure
  2. Water pressure in the hole
  3. Detonation pressure at the front
  4. Gas (explosion) pressure
Show answer & solution

Answer: (D) Gas (explosion) pressure

Expanding gases push the broken burden forward.

Question 8

Which pressure mainly crushes and shatters rock close to the hole?

  1. Hydrostatic pressure
  2. Detonation (shock) pressure
  3. Gas pressure
  4. Atmospheric pressure
Show answer & solution

Answer: (B) Detonation (shock) pressure

The shock wave crushes rock near the wall and starts radial cracks.

Question 9

What is the linear charge concentration in a blast hole?

  1. Total explosive per blast
  2. Number of holes per delay
  3. Mass of explosive per metre of hole
  4. Explosive per cubic metre of rock
Show answer & solution

Answer: (C) Mass of explosive per metre of hole

It is calculated from hole diameter and explosive density.

Question 10

Which formula gives the linear charge concentration q for hole diameter d and explosive density ρ?

  1. q = πd²ρ/4
  2. q = 4ρ/(πd²)
  3. q = d²/ρ
  4. q = πdρ
Show answer & solution

Answer: (A) q = πd²ρ/4

It is the cross-sectional area of the charge multiplied by density.

Question 11

What is relative weight strength (RWS) of an explosive?

  1. Sensitivity to impact
  2. Mass of explosive per hole
  3. Energy per unit volume compared with ANFO
  4. Energy per unit mass compared with ANFO taken as 100
Show answer & solution

Answer: (D) Energy per unit mass compared with ANFO taken as 100

RWS compares explosives on an equal-weight basis.

Question 12

What is relative bulk strength (RBS) of an explosive?

  1. Shelf life rating
  2. Water resistance rating
  3. Energy per unit mass compared with ANFO
  4. Energy per unit volume compared with ANFO taken as 100
Show answer & solution

Answer: (D) Energy per unit volume compared with ANFO taken as 100

RBS accounts for density as well as energy.

Question 13

What is oxygen balance of an explosive?

  1. The amount of oxygen used by miners
  2. The oxygen content of air in a mine
  3. The excess or deficiency of oxygen needed to fully oxidise the fuels
  4. The ratio of fuel oil to water
Show answer & solution

Answer: (C) The excess or deficiency of oxygen needed to fully oxidise the fuels

Oxygen balance controls energy release and fume quality.

Question 14

What oxygen balance is ideal for commercial explosives?

  1. About zero (slightly positive)
  2. It does not matter
  3. Strongly negative
  4. Strongly positive
Show answer & solution

Answer: (A) About zero (slightly positive)

Near-zero oxygen balance gives maximum energy and minimum toxic gases.

Question 15

What is the fume class of an explosive?

  1. A rating of its cost
  2. A rating of the toxic gases it produces
  3. A rating of its density
  4. A rating of its colour
Show answer & solution

Answer: (B) A rating of the toxic gases it produces

Fume class is important for underground blasting.

Question 16

Which toxic gases are mainly produced by poor detonation of explosives?

  1. Carbon monoxide and nitrogen oxides
  2. Methane and hydrogen
  3. Helium and argon
  4. Oxygen and nitrogen
Show answer & solution

Answer: (A) Carbon monoxide and nitrogen oxides

CO and NOx are the main toxic blasting fumes.

Question 17

What is the sensitivity of an explosive?

  1. Its shelf life
  2. Its water resistance
  3. Its energy per kilogram
  4. The ease with which it can be initiated
Show answer & solution

Answer: (D) The ease with which it can be initiated

Sensitivity to detonators, impact, friction and heat must be known.

Question 18

What does the gap test measure for cartridged explosives?

  1. Density
  2. Water resistance
  3. Ability of detonation to propagate from one cartridge to another across a gap
  4. Shelf life
Show answer & solution

Answer: (C) Ability of detonation to propagate from one cartridge to another across a gap

A larger gap that still propagates means higher sensitiveness.

Question 19

What does water resistance of an explosive mean?

  1. Its ability to float on water
  2. Its ability to withstand water without losing the ability to detonate
  3. Its ability to absorb water
  4. Its use for drinking water treatment
Show answer & solution

Answer: (B) Its ability to withstand water without losing the ability to detonate

Water resistance decides which explosives can be used in wet holes.

Question 20

What is dead pressing in blasting?

  1. Pressing cartridges firmly into the hole
  2. Packing stemming tightly
  3. Loss of sensitivity of an explosive due to high pressure from adjacent detonations or water depth
  4. Over-tamping of black powder
Show answer & solution

Answer: (C) Loss of sensitivity of an explosive due to high pressure from adjacent detonations or water depth

Dead-pressed charges may fail to detonate.

Question 21

What is the channel effect in cartridged explosives?

  1. The path of flyrock
  2. A ventilation airway
  3. A channel cut in rock for drainage
  4. Desensitisation caused by an air gap between cartridges and the hole wall
Show answer & solution

Answer: (D) Desensitisation caused by an air gap between cartridges and the hole wall

An air shock running ahead in the gap compresses unreacted explosive.

Question 22

What is the shelf life of an explosive?

  1. The period during which it keeps its specified properties in storage
  2. The time it takes to detonate
  3. The time between blasts
  4. The time it takes to load a hole
Show answer & solution

Answer: (A) The period during which it keeps its specified properties in storage

Explosives used after their shelf life may misfire.

Question 23

What is the coupling ratio in a blast hole?

  1. Ratio of stemming to charge length
  2. Ratio of charge diameter to hole diameter
  3. Ratio of explosive to rock mass
  4. Ratio of burden to spacing
Show answer & solution

Answer: (B) Ratio of charge diameter to hole diameter

Fully coupled charges fill the hole completely.

Question 24

What is the main effect of decoupling a charge?

  1. It increases hole wall damage
  2. It reduces the pressure on the hole wall and the damage around it
  3. It increases detonation velocity greatly
  4. It makes the explosive more sensitive
Show answer & solution

Answer: (B) It reduces the pressure on the hole wall and the damage around it

Decoupling is used in perimeter and pre-split blasting.

Question 25

What is impedance matching in blasting?

  1. Matching hole depth with bench height
  2. Matching delay timing with distance
  3. Matching truck size with bucket size
  4. Matching the detonation impedance of the explosive with the acoustic impedance of the rock for efficient energy transfer
Show answer & solution

Answer: (D) Matching the detonation impedance of the explosive with the acoustic impedance of the rock for efficient energy transfer

Hard, dense rock is best broken by dense, high-VOD explosives.

Question 26

How is the acoustic impedance of rock calculated?

  1. Density divided by P-wave velocity
  2. Density multiplied by porosity
  3. Density multiplied by P-wave velocity
  4. P-wave velocity divided by density
Show answer & solution

Answer: (C) Density multiplied by P-wave velocity

Characteristic impedance is ρV.

Question 27

Into which two main forms is the energy of an explosive in rock usually divided?

  1. Shock energy and gas (heave) energy
  2. Light energy and sound energy only
  3. Electrical and magnetic energy
  4. Chemical and nuclear energy
Show answer & solution

Answer: (A) Shock energy and gas (heave) energy

Shock energy fractures rock; gas energy heaves and displaces it.

Question 28

Which explosive properties are preferred for hard, massive rock?

  1. Low VOD and low density
  2. Low energy and high water content
  3. High fuel oil and low oxygen
  4. High VOD and high density
Show answer & solution

Answer: (D) High VOD and high density

High shock energy is needed to fracture strong intact rock.

Question 29

Which type of explosive is generally preferred for soft or highly jointed rock?

  1. Black powder in large holes
  2. Detonating cord only
  3. Low-VOD explosive with high gas energy, such as ANFO
  4. Very high-VOD cast explosive
Show answer & solution

Answer: (C) Low-VOD explosive with high gas energy, such as ANFO

Gas energy works well where joints already divide the rock.

Question 30

What does cap-sensitive mean for an explosive?

  1. It is initiated only by a booster
  2. It can be initiated by a standard No. 8 detonator alone
  3. It is sensitive to heat only
  4. It cannot be initiated
Show answer & solution

Answer: (B) It can be initiated by a standard No. 8 detonator alone

Cap-sensitive explosives include dynamite and many cartridged emulsions.

Question 31

Which detonator strength is used as the standard for testing cap sensitivity?

  1. No. 8 detonator
  2. No. 1 detonator
  3. No. 20 detonator
  4. No. 100 detonator
Show answer & solution

Answer: (A) No. 8 detonator

A No. 8 detonator has a defined base charge strength.

Question 32

What is the typical density of poured ANFO?

  1. About 0.2 g/cm³
  2. About 0.8 g/cm³
  3. About 1.6 g/cm³
  4. About 3.0 g/cm³
Show answer & solution

Answer: (B) About 0.8 g/cm³

Poured ANFO has a density of about 0.8–0.85 g/cm³.

Question 33

What is the typical density of emulsion explosives?

  1. About 0.3 g/cm³
  2. About 1.1 to 1.3 g/cm³
  3. About 2.5 g/cm³
  4. About 5.0 g/cm³
Show answer & solution

Answer: (B) About 1.1 to 1.3 g/cm³

Higher density gives emulsions more energy per metre of hole.

Question 34

Why must ammonium nitrate be protected from moisture?

  1. It becomes too sensitive when wet
  2. It becomes radioactive
  3. It turns into fuel oil
  4. It is hygroscopic and loses its sensitivity when damp
Show answer & solution

Answer: (D) It is hygroscopic and loses its sensitivity when damp

Damp or caked AN performs poorly and produces NOx.

Question 35

What is the heat of explosion of an explosive?

  1. The heat released per unit mass when it detonates
  2. The heat needed to ignite it
  3. The temperature at which it melts
  4. The temperature of the magazine
Show answer & solution

Answer: (A) The heat released per unit mass when it detonates

Heat of explosion is the basis of explosive strength calculations.

Question 36

Which test traditionally measures the strength of an explosive by the expansion of a cavity in a lead cylinder?

  1. Dautriche test
  2. Gap test
  3. Trauzl lead block test
  4. Slake durability test
Show answer & solution

Answer: (C) Trauzl lead block test

The enlargement of the cavity indicates relative strength.

Question 37

How does confinement affect the performance of ANFO?

  1. Confinement stops detonation
  2. Confinement reduces gas pressure only
  3. Confinement has no effect
  4. Better confinement raises its VOD and reliability
Show answer & solution

Answer: (D) Better confinement raises its VOD and reliability

Strong confinement helps non-ideal explosives react fully.

Question 38

What is the effect of water on poured ANFO in a blast hole?

  1. It dissolves the ammonium nitrate, reducing energy and causing misfires and NOx fumes
  2. It makes ANFO cap-sensitive
  3. It has no effect
  4. It increases ANFO's VOD
Show answer & solution

Answer: (A) It dissolves the ammonium nitrate, reducing energy and causing misfires and NOx fumes

Wet holes need emulsion, heavy ANFO or lined holes.

Practice these 38 questions interactively →