Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Explosives & Blasting: Blast Design

Mining Engineering · Explosives & Blasting

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the burden in bench blasting?

  1. The distance from a blast hole to the nearest free face, at right angles
  2. The length of stemming
  3. The distance between holes in a row
  4. The depth of the hole
Show answer & solution

Answer: (A) The distance from a blast hole to the nearest free face, at right angles

Burden is the most important design parameter.

Question 2

What is the spacing in bench blasting?

  1. The depth below grade
  2. The height of the bench
  3. The distance to the free face
  4. The distance between adjacent holes in the same row
Show answer & solution

Answer: (D) The distance between adjacent holes in the same row

Spacing is usually 1.0–1.5 times the burden.

Question 3

What is the main purpose of stemming?

  1. To measure hole depth
  2. To confine the explosive gases and reduce airblast and flyrock
  3. To drain water from the hole
  4. To initiate the explosive
Show answer & solution

Answer: (B) To confine the explosive gases and reduce airblast and flyrock

Stemming keeps gas pressure in the hole long enough to work on the rock.

Question 4

Which material makes the best stemming?

  1. Dry clay powder only
  2. Paper
  3. Crushed angular stone chips
  4. Fine drill cuttings with water
Show answer & solution

Answer: (C) Crushed angular stone chips

Angular chips lock together and resist ejection.

Question 5

What stemming length is commonly used in bench blasting?

  1. About 3 times the burden
  2. About 0.1 times the burden
  3. No stemming
  4. About 0.7 to 1.0 times the burden
Show answer & solution

Answer: (D) About 0.7 to 1.0 times the burden

Too little stemming causes flyrock; too much leaves boulders at the top.

Question 6

By what rule of thumb is burden often estimated from hole diameter?

  1. About 25 to 40 times the hole diameter
  2. About 2 to 4 times the hole diameter
  3. About 100 to 150 times the hole diameter
  4. Equal to the hole diameter
Show answer & solution

Answer: (A) About 25 to 40 times the hole diameter

Denser explosives and weaker rock allow larger burdens.

Question 7

What spacing-to-burden ratio is commonly used in bench blasting?

  1. 0.2 to 0.5
  2. 1.0 to 1.5
  3. 3 to 4
  4. 5 to 10
Show answer & solution

Answer: (B) 1.0 to 1.5

An S/B ratio of about 1.25 is common for staggered patterns.

Question 8

What is powder factor?

  1. Mass of explosive used per unit volume or mass of rock blasted
  2. Energy of one detonator
  3. Depth of hole per metre of burden
  4. Number of holes per blast
Show answer & solution

Answer: (A) Mass of explosive used per unit volume or mass of rock blasted

It is expressed in kg/m³ or kg/t.

Question 9

What is a typical powder factor range for surface bench blasting?

  1. About 0.01 kg/m³
  2. About 0.3 to 0.8 kg/m³
  3. About 5 to 10 kg/m³
  4. About 20 kg/m³
Show answer & solution

Answer: (B) About 0.3 to 0.8 kg/m³

Harder rock and finer fragmentation need higher powder factors.

Question 10

What is the stiffness ratio in bench blasting?

  1. Burden divided by spacing
  2. Stemming divided by sub-drill
  3. Bench height divided by burden
  4. Spacing divided by hole diameter
Show answer & solution

Answer: (C) Bench height divided by burden

A stiffness ratio above about 3 gives good fragmentation.

Question 11

What is the effect of a stiffness ratio of less than about 2?

  1. Excellent fragmentation
  2. Reduced drilling only
  3. No effect
  4. Poor fragmentation, flyrock and toe problems
Show answer & solution

Answer: (D) Poor fragmentation, flyrock and toe problems

A stiff burden does not flex and breaks poorly.

Question 12

In Ash's design method, what burden ratio KB is used for average rock with average explosive?

  1. 0.3
  2. 3
  3. 30
  4. 300
Show answer & solution

Answer: (C) 30

Ash's standard: B = 30 × hole diameter, adjusted for rock and explosive.

Question 13

Which blast design formula relates maximum burden to linear charge concentration and a rock constant?

  1. Langefors–Kihlström formula
  2. Rosin–Rammler distribution
  3. Kuz-Ram model
  4. Ash formula only
Show answer & solution

Answer: (A) Langefors–Kihlström formula

Langefors and Kihlström's work is a basis of Scandinavian blast design.

Question 14

What does the Kuz-Ram model predict?

  1. Ground vibration at a distance
  2. Stemming length
  3. Airblast level
  4. Fragmentation size distribution of the blasted rock
Show answer & solution

Answer: (D) Fragmentation size distribution of the blasted rock

It combines Kuznetsov's mean size equation with the Rosin–Rammler distribution.

Question 15

Which drilling pattern usually gives better distribution of explosive energy?

  1. Square pattern
  2. Staggered pattern
  3. Random pattern
  4. Single-row pattern
Show answer & solution

Answer: (B) Staggered pattern

Staggered holes reduce the size of the area furthest from any hole.

Question 16

What is decking in a blast hole?

  1. Loading holes in one continuous column
  2. Drilling below grade
  3. Dividing the explosive column into separate charges with inert stemming between them
  4. Covering the blast with mats
Show answer & solution

Answer: (C) Dividing the explosive column into separate charges with inert stemming between them

Decking reduces charge per delay and places explosive where needed.

Question 17

What is the purpose of air decking?

  1. To increase flyrock
  2. To store air for miners
  3. To cool the explosive
  4. To reduce explosive use while improving energy distribution
Show answer & solution

Answer: (D) To reduce explosive use while improving energy distribution

An air gap in the column prolongs gas pressure and reduces crushing.

Question 18

Why is a free face essential in blasting?

  1. It allows the broken rock to move and stress waves to reflect as tension
  2. It holds stemming
  3. It stops vibration
  4. It increases confinement
Show answer & solution

Answer: (A) It allows the broken rock to move and stress waves to reflect as tension

Rock breaks much more easily towards a free face.

Question 19

How does increasing the number of free faces affect a blast?

  1. It requires more explosive
  2. It improves breakage and reduces explosive needed
  3. It stops the blast
  4. It has no effect
Show answer & solution

Answer: (B) It improves breakage and reduces explosive needed

Corner blasts with two free faces need less explosive.

Question 20

What is the most common cause of hard toe in bench blasting?

  1. Too much stemming
  2. Too much water spray
  3. Insufficient sub-drilling or excessive burden at the floor
  4. Too many delays
Show answer & solution

Answer: (C) Insufficient sub-drilling or excessive burden at the floor

Without enough energy at grade, the toe remains unbroken.

Question 21

What usually causes backbreak behind the last row of a blast?

  1. Too little burden in the front row
  2. Using electronic detonators
  3. Too short hole depth only
  4. Excessive burden or stemming in the back row and too short delays between rows
Show answer & solution

Answer: (D) Excessive burden or stemming in the back row and too short delays between rows

Confined back rows push gas into the rock behind.

Question 22

What is the purpose of V or echelon initiation patterns?

  1. To reduce drilling
  2. To control the direction of rock movement and improve fragmentation
  3. To fire all holes at once
  4. To remove stemming
Show answer & solution

Answer: (B) To control the direction of rock movement and improve fragmentation

Changing the firing sequence changes the effective burden and spacing.

Question 23

When are pre-split holes fired relative to the main blast?

  1. Before the main blast
  2. After the main blast
  3. At the same instant as the last row
  4. They are never fired
Show answer & solution

Answer: (A) Before the main blast

Pre-split forms a crack that limits damage behind the final wall.

Question 24

Which controlled blasting technique fires the perimeter holes after the main blast?

  1. Pre-splitting
  2. Cast blasting
  3. Line drilling
  4. Smooth (cushion or trim) blasting
Show answer & solution

Answer: (D) Smooth (cushion or trim) blasting

Smooth blasting trims the final profile with light charges.

Question 25

What spacing is typically used for pre-split holes?

  1. About 100 times the hole diameter
  2. About 30 to 40 times the hole diameter
  3. About 10 to 12 times the hole diameter
  4. About equal to the burden of production holes
Show answer & solution

Answer: (C) About 10 to 12 times the hole diameter

Close spacing lets cracks link between holes.

Question 26

How does the specific charge in tunnel blasting compare with bench blasting?

  1. It is much higher
  2. It is the same
  3. It is zero
  4. It is much lower
Show answer & solution

Answer: (A) It is much higher

Tunnel rounds have only one free face and high confinement.

Question 27

Why does tunnel blasting need more explosive per cubic metre than bench blasting?

  1. Tunnels have larger holes
  2. There is only one free face and the rock is highly confined
  3. Tunnels are always in softer rock
  4. Tunnels use no stemming
Show answer & solution

Answer: (B) There is only one free face and the rock is highly confined

The cut must create its own free space first.

Question 28

What is the powder factor if 500 kg of explosive breaks 1,000 m³ of rock?

  1. 0.05 kg/m³
  2. 0.5 kg/m³
  3. 2 kg/m³
  4. 5 kg/m³
Show answer & solution

Answer: (B) 0.5 kg/m³

500/1000 = 0.5 kg/m³.

Question 29

What volume of rock is broken per hole with a burden of 4 m, spacing of 5 m and bench height of 10 m?

  1. 20 m³
  2. 90 m³
  3. 200 m³
  4. 2,000 m³
Show answer & solution

Answer: (C) 200 m³

Volume = B × S × H = 4 × 5 × 10 = 200 m³.

Question 30

If each hole breaks 200 m³ and the powder factor is 0.5 kg/m³, how much explosive is needed per hole?

  1. 40 kg
  2. 100 kg
  3. 200 kg
  4. 400 kg
Show answer & solution

Answer: (B) 100 kg

200 × 0.5 = 100 kg per hole.

Question 31

What is the approximate linear charge concentration of ANFO (density 0.8 g/cm³) in a 115 mm hole?

  1. 0.83 kg/m
  2. 3.3 kg/m
  3. 8.3 kg/m
  4. 83 kg/m
Show answer & solution

Answer: (C) 8.3 kg/m

q = π × 0.115² /4 × 800 ≈ 8.3 kg/m.

Question 32

What is pop shooting in secondary blasting?

  1. Firing a small charge in a short hole drilled into a boulder
  2. Firing a charge laid on top of a boulder
  3. Firing the main blast
  4. Firing perimeter holes
Show answer & solution

Answer: (A) Firing a small charge in a short hole drilled into a boulder

Pop shooting uses less explosive than mudcapping.

Question 33

What is mudcapping (plaster shooting)?

  1. Using mud as stemming in production holes
  2. Covering the main blast with mats
  3. Firing a charge in a drilled hole
  4. Firing a charge placed on the surface of a boulder and covered with mud
Show answer & solution

Answer: (D) Firing a charge placed on the surface of a boulder and covered with mud

Mudcapping needs no drilling but produces high airblast.

Question 34

How is fragmentation of a blasted muckpile commonly assessed today?

  1. Digital image analysis of photographs
  2. Measuring the stemming length
  3. Weighing each rock by hand
  4. Counting drill holes
Show answer & solution

Answer: (A) Digital image analysis of photographs

Software such as WipFrag estimates size distribution from images.

Question 35

What is the overall goal in choosing optimum fragmentation?

  1. Producing the largest possible boulders
  2. Maximising flyrock
  3. Using the least explosive regardless of other costs
  4. Minimising the total cost of drilling, blasting, loading, hauling and crushing
Show answer & solution

Answer: (D) Minimising the total cost of drilling, blasting, loading, hauling and crushing

Better fragmentation raises blasting cost but lowers downstream costs.

Question 36

What is sub-drill in blast design used to achieve?

  1. Better stemming
  2. Full breakage of the rock at floor level
  3. Less explosive in the hole
  4. Smaller burden
Show answer & solution

Answer: (B) Full breakage of the rock at floor level

Sub-drill places explosive energy below grade to break the toe.

Question 37

What is the main purpose of the cut holes in an underground development round?

  1. To create the initial opening towards which the rest of the round breaks
  2. To lift the muck pile
  3. To trim the walls
  4. To form the final roof profile
Show answer & solution

Answer: (A) To create the initial opening towards which the rest of the round breaks

The cut provides a second free face for the round.

Question 38

What is the effect of too small a burden in the front row?

  1. No breakage at all
  2. Flyrock and airblast from the face
  3. Hard toes and boulders
  4. Lower vibration
Show answer & solution

Answer: (B) Flyrock and airblast from the face

The explosive gas breaks out through the thin face too easily.

Practice these 38 questions interactively →