In which unit is blast-induced ground vibration usually measured?
Show answer & solution
Answer: (C) Peak particle velocity (PPV) in mm/s
PPV is the standard measure of ground vibration intensity.
Mining Engineering · Explosives & Blasting
37 questions, each with the answer and a worked solution.
Practice interactively and track your score →In which unit is blast-induced ground vibration usually measured?
Answer: (C) Peak particle velocity (PPV) in mm/s
PPV is the standard measure of ground vibration intensity.
Which instrument records blast ground vibration and airblast?
Answer: (D) Seismograph (blast monitor)
Blast monitors record PPV, frequency and air overpressure.
How is scaled distance calculated for ground vibration?
Answer: (C) Distance divided by the square root of maximum charge per delay
SD = D/√W is used in vibration prediction.
Which charge quantity mainly controls ground vibration from a blast?
Answer: (B) Maximum charge fired per delay
Holes firing at least 8 ms apart are usually treated as separate delays.
What is the most direct way to reduce ground vibration from a blast?
Answer: (A) Reduce the charge per delay by using more delays or decking
Lower instantaneous charge gives lower PPV.
Which agency's study (RI 8507) set widely used building damage criteria based on PPV and frequency?
Answer: (D) US Bureau of Mines
USBM RI 8507 (1980) gave frequency-based safe vibration limits.
Why are low-frequency blast vibrations more damaging to buildings?
Answer: (D) They are close to the natural frequencies of structures
Resonance amplifies building response at low frequencies.
How is airblast (air overpressure) usually measured?
Answer: (C) In decibels (linear scale) or pascals
Airblast is measured with a microphone on a blast monitor.
What are common causes of high airblast?
Answer: (B) Insufficient stemming, exposed detonating cord and face blowouts
Gas escaping directly to the atmosphere creates air pressure waves.
What is flyrock?
Answer: (A) Rock thrown unexpectedly far from the blast area
Flyrock is a leading cause of blasting injuries.
What are the main causes of flyrock?
Answer: (A) Too small a burden or too little stemming and weak zones in the rock
Gas escapes through weak paths and throws rock.
What is the main control against injury from flyrock?
Answer: (B) Proper blast design and clearing everyone beyond the danger zone
Blast guards prevent entry into the danger zone.
Why must workers wait before re-entering a working place after an underground blast?
Answer: (C) To allow toxic fumes and dust to clear
Ventilation must remove CO and NOx before re-entry.
What is overbreak in underground blasting?
Answer: (D) Rock broken beyond the designed excavation profile
Overbreak increases mucking and support costs.
What is the blast damage zone?
Answer: (B) The zone of rock around the excavation weakened by blasting
Damage reduces rock mass strength and stability.
What does the half-cast (half-barrel) factor measure?
Answer: (A) The percentage of visible half holes on the final wall, indicating controlled blasting quality
A high half-cast factor shows little damage to the final wall.
How does increasing the delay between rows usually affect the muckpile?
Answer: (C) It gives more forward movement and a looser muckpile
Longer row delays allow each row to move before the next fires.
What is a disadvantage of coarse blast fragmentation?
Answer: (D) Slower loading, more secondary breaking and higher crusher costs
Boulders reduce shovel productivity and block crushers.
What is a disadvantage of excessively fine fragmentation?
Answer: (A) Higher explosive cost and excess fines and dust
Overblasting wastes explosive and may lower product value.
Why can a temperature inversion increase airblast problems?
Answer: (B) It bends sound waves back towards the ground, carrying noise further
Blasts are often avoided during inversions and strong winds towards houses.
How does peak particle velocity change with increasing distance from the blast?
Answer: (C) It decreases
Energy spreads out and is absorbed with distance.
What is the site-specific relation between PPV and scaled distance called?
Answer: (D) Attenuation (propagation) law
PPV = K(SD)^−b, with K and b found from site monitoring.
What is the main purpose of a pre-blast survey of nearby buildings?
Answer: (B) To record existing cracks and condition so that damage claims can be judged fairly
Photographs and notes are taken before blasting begins.
Which waves dominate blast vibration at larger distances?
Answer: (A) Surface (Rayleigh) waves
Surface waves decay more slowly with distance than body waves.
Why is carbon monoxide from blasting particularly dangerous?
Answer: (D) It is colourless and odourless
CO can poison workers without any warning sign.
What does orange-brown smoke after a blast usually indicate?
Answer: (C) Nitrogen oxides from poor detonation, often due to wet or poorly mixed ANFO
NOx fumes are toxic and indicate inefficient detonation.
Why is overbreak undesirable in tunnels and roadways?
Answer: (A) It adds mucking, support and lining cost and reduces stability
Controlled perimeter blasting limits overbreak.
How is the blasting of holes near sensitive structures such as dams and pipelines controlled?
Answer: (C) By setting PPV limits and designing the charge per delay to meet them
Monitoring confirms that limits are being met.
What is the scaled distance for a distance of 100 m and a maximum charge per delay of 25 kg?
Answer: (C) 20 m/kg^0.5
SD = 100/√25 = 100/5 = 20.
What maximum charge per delay is allowed at 200 m if the required scaled distance is 25 m/kg^0.5?
Answer: (C) 64 kg
W = (D/SD)² = (200/25)² = 64 kg.
Which blasting product is used to cover small blasts near buildings to stop flyrock?
Answer: (B) Blasting mats
Heavy rubber or rope mats hold down broken rock.
What is the effect of firing too many holes on the same delay?
Answer: (D) Higher ground vibration and poorer fragmentation
Many holes on one delay act like one large charge.
What is the effect of wind blowing towards nearby houses at the time of a blast?
Answer: (C) It carries airblast and dust further towards the houses
Blasts are scheduled when the wind blows away from sensitive areas.
Which property of the rock mass increases the risk of flyrock from a blast hole?
Answer: (B) Weak seams, cavities or open joints near the hole
Gas escapes rapidly through weak zones and throws fragments.
What is the main purpose of monitoring every blast near a residential area?
Answer: (D) To show compliance with vibration and airblast limits and adjust designs
Records protect both the mine and nearby residents.
How does good stemming affect airblast?
Answer: (A) It reduces airblast by confining the gases
Ejected stemming is a common source of noise and dust.
What is the term for vibration felt by people at levels below those that damage buildings?
Answer: (B) Human perception threshold
People notice vibration at about 0.5 mm/s, far below damage levels.