What is the function of a governor?
Show answer & solution
Answer: (C) To keep the mean speed of an engine nearly constant under varying load by controlling fuel supply
A flywheel controls cyclic fluctuations.
Mechanical Engineering · Theory of Machines
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the function of a governor?
Answer: (C) To keep the mean speed of an engine nearly constant under varying load by controlling fuel supply
A flywheel controls cyclic fluctuations.
What is the difference between a flywheel and a governor?
Answer: (D) A flywheel controls speed fluctuation within a cycle, while a governor controls mean speed over many cycles
A flywheel acts as an energy reservoir.
What is a Watt governor?
Answer: (A) A simple centrifugal pendulum-type governor without a central load
It is suitable only for low speeds.
What is a Porter governor?
Answer: (B) A Watt governor with a heavy central load on the sleeve
The central load allows it to work at higher speeds.
What is a Proell governor?
Answer: (C) A Porter-type governor with the balls attached to extensions of the lower arms
It is more sensitive than a Porter governor of the same size.
What is a Hartnell governor?
Answer: (A) A spring-loaded centrifugal governor
Its spring force replaces the weight of the central load.
Which type of governor was commonly used to adjust the speed of gramophone turntables?
Answer: (D) Pickering governor
It uses leaf springs carrying weights.
What is the sensitiveness of a governor?
Answer: (B) The ratio of the range of speed to the mean speed
A smaller range of speed means a more sensitive governor.
What is an isochronous governor?
Answer: (A) A governor with the same equilibrium speed at all sleeve positions (zero range of speed)
A pendulum governor cannot be isochronous.
What is hunting of a governor?
Answer: (C) Continuous fluctuation of engine speed above and below the mean speed
It occurs when a governor is too sensitive.
What is a stable governor?
Answer: (B) One in which the ball radius increases as equilibrium speed increases
Stability and sensitiveness must be balanced.
What is the power of a governor?
Answer: (D) The work done at the sleeve for a given percentage change in speed
It equals mean effort × lift of sleeve.
What is the effort of a governor?
Answer: (B) The mean force exerted at the sleeve for a given percentage change in speed
Effort and power show a governor's ability to overcome friction.
What is a turning moment diagram?
Answer: (A) A graph of the turning moment on the crankshaft against crank angle
It is used to design flywheels.
What is the coefficient of fluctuation of speed?
Answer: (D) The ratio of the maximum fluctuation of speed to the mean speed
Cs = (N₁ − N₂)/N.
What is the maximum fluctuation of energy stored in a flywheel?
Answer: (C) Iω²Cs
I is moment of inertia, ω mean angular speed and Cs coefficient of fluctuation of speed.
Why is a heavier flywheel needed for a single-cylinder four-stroke engine than for a multi-cylinder engine?
Answer: (D) Its turning moment fluctuates more because it has only one power stroke in two revolutions
Multi-cylinder engines have a smoother turning moment.
What is a brake?
Answer: (B) A device that absorbs energy to slow or stop a moving body by friction
Absorbed energy is converted to heat.
What type of brake is used in most automobile wheels (drum type)?
Answer: (C) Internal expanding shoe brake
Disc brakes are also widely used.
What is a self-energising brake?
Answer: (A) A brake in which the friction force helps to apply the brake
If the friction force alone can apply it, it is self-locking.
What is a band brake?
Answer: (B) A brake in which a flexible band wrapped around a drum is tightened to apply friction
Its tension ratio follows T₁/T₂ = e^(μθ).
What is a dynamometer?
Answer: (C) A device for measuring the power output or torque of an engine or motor
Dynamometers are of absorption and transmission types.
Which of the following is an absorption dynamometer?
Answer: (A) Prony brake
Absorption dynamometers convert the power into heat.
Which is a transmission dynamometer?
Answer: (D) Torsion dynamometer
Transmission dynamometers measure power while it is being transmitted.
What is a clutch?
Answer: (A) A device for engaging and disengaging a driven shaft from a driving shaft while running
Friction clutches are used in vehicles.
Why is the uniform wear theory used for designing friction clutches?
Answer: (C) It gives a lower, safer estimate of the torque transmitted after the clutch has worn
Uniform pressure theory applies to new clutches.
What is a centrifugal clutch?
Answer: (B) A clutch engaged automatically by centrifugal force on shoes when speed rises
It is used in mopeds and small motorcycles.
What type of bearing is well suited to fluctuating loads in a small radial space?
Answer: (D) Needle roller bearing
Needle bearings have high load capacity for their size.
In an ideal (frictionless) machine, how does output compare with input?
Answer: (B) They are equal
Actual machines have efficiency below 100%.
What is the height of a Watt governor in terms of speed N (rpm)?
Answer: (C) h = 895/N² metres
Height decreases rapidly as speed increases, so it suits low speeds.
Why is the Watt governor unsuitable for high-speed engines?
Answer: (B) The change in height becomes very small at high speeds, making it insensitive
Loaded governors are used for higher speeds.
What is the function of the flywheel in a punching press?
Answer: (D) To store energy during idle periods and supply it during the punching stroke
A smaller motor can then be used.
What is a rope brake dynamometer?
Answer: (A) An absorption dynamometer using a rope wrapped around the flywheel
Brake power = (W − S)πDN/60.
What is a cone clutch?
Answer: (B) A friction clutch with conical friction surfaces
The wedging action increases the normal force.
What is a single plate clutch commonly used for?
Answer: (D) Transmitting power from the engine to the gearbox in cars
Both sides of the plate act as friction surfaces.
What is the friction circle of a journal bearing?
Answer: (A) A circle of radius μr (approximately) to which the resultant reaction is tangent
It is used to analyse friction in pin joints.