What is the velocity ratio of a belt drive (neglecting slip and thickness)?
Show answer & solution
Answer: (A) N₂/N₁ = D₁/D₂
The smaller pulley rotates faster.
Mechanical Engineering · Theory of Machines
43 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the velocity ratio of a belt drive (neglecting slip and thickness)?
Answer: (A) N₂/N₁ = D₁/D₂
The smaller pulley rotates faster.
To which pulley dimension is belt speed directly proportional, for a given driver speed?
Answer: (D) Diameter of the driving pulley
v = πD₁N₁/60.
What is slip in a belt drive?
Answer: (B) Lack of grip between belt and pulley, reducing the speed of the driven pulley
It is expressed as a percentage.
What is creep in a belt drive?
Answer: (B) Relative motion between belt and pulley due to unequal stretching on the tight and slack sides
Creep slightly reduces the speed of the driven pulley.
What is the ratio of tensions in a flat belt drive?
Answer: (A) T₁/T₂ = e^(μθ)
θ is the angle of contact in radians.
Why does a V-belt transmit more power than a flat belt of the same size?
Answer: (D) The wedging action in the groove increases the effective friction
T₁/T₂ = e^(μθ cosec β) for a V-belt.
On which factors does the power transmitted by a belt depend?
Answer: (C) Tight-side tension, slack-side tension and belt speed
P = (T₁ − T₂)v.
What is the condition for maximum power transmission by a belt, considering centrifugal tension?
Answer: (B) Centrifugal tension equals one-third of the maximum tension
The belt speed is then v = √(T/3m).
What is the purpose of an idler (jockey) pulley?
Answer: (D) To increase belt tension and the angle of contact
It is used where centre distance is short.
Why is crowning provided on flat belt pulleys?
Answer: (A) To keep the belt running at the centre of the pulley
The belt tends to climb to the highest point.
What is the main use of a crossed belt drive?
Answer: (C) Making the driven shaft rotate in the opposite direction to the driver
The angle of contact is the same on both pulleys.
In a multi-V-belt drive, what should be done if one belt breaks?
Answer: (C) Replace all the belts as a matched set
New and old belts stretch differently and share load unevenly.
What is the main advantage of chain drives over belt drives?
Answer: (A) They give a positive drive with no slip
Bicycles and motorcycles use chain drives.
What is the law of gearing?
Answer: (B) The common normal at the point of contact of two teeth must always pass through the pitch point
It ensures a constant angular velocity ratio.
Which tooth profile is most widely used for gears?
Answer: (D) Involute profile
Involute gears are easy to manufacture and tolerate centre-distance changes.
What curve is traced by a point on a thread unwound from a cylinder?
Answer: (A) An involute
The involute is the basis of most gear teeth.
What is the standard pressure angle of modern involute gears?
Answer: (B) 20°
Older systems used 14.5°.
What is the module of a gear?
Answer: (C) The ratio of pitch circle diameter (mm) to the number of teeth
Circular pitch = π × module.
What is interference in involute gears?
Answer: (D) Contact of the tip of one tooth with the non-involute part of the mating tooth
It is avoided by having enough teeth on the pinion or using undercut teeth.
Which gears connect parallel shafts?
Answer: (D) Spur and helical gears
Helical gears run more smoothly than spur gears.
Why are helical gears quieter than spur gears?
Answer: (A) Their teeth engage gradually rather than all at once
However, they produce axial thrust.
Which gears eliminate axial thrust while keeping the advantages of helical teeth?
Answer: (B) Double helical (herringbone) gears with opposite hands
The axial thrusts of the two halves cancel out.
Which gears connect shafts whose axes intersect?
Answer: (C) Bevel gears
Mitre gears are bevel gears of equal size at right angles.
Which gear drive connects shafts that are neither parallel nor intersecting and gives a high speed reduction?
Answer: (A) Worm and worm wheel
Worm drives can be self-locking.
What is a rack and pinion used for?
Answer: (D) Converting rotary motion into linear motion, or vice versa
It is used in vehicle steering systems.
What is the function of an idler gear in a simple gear train?
Answer: (C) To change the direction of rotation of the driven gear without changing the speed ratio
It also fills the space between the driver and driven gears.
What is a compound gear train?
Answer: (B) A train in which two or more gears are mounted on the same intermediate shaft
It gives a large speed ratio in a small space.
What is a reverted gear train?
Answer: (D) A compound train in which the first and last gears are on the same axis
It is used in clocks and lathe back gears.
What is an epicyclic gear train?
Answer: (C) A train in which the axis of at least one gear moves relative to the frame
It gives high speed ratios compactly and is used in differentials.
What is the function of the differential in an automobile?
Answer: (B) Allowing the rear wheels to rotate at different speeds when turning
It is an epicyclic gear train.
What is a Hooke's joint (universal joint) used for?
Answer: (A) Connecting two shafts whose axes intersect at a small angle
It transmits power from the gearbox to the differential.
What type of pair is a universal (Hooke's) joint?
Answer: (C) Lower pair
It consists of two forks joined by a cross-piece.
How can the speed variation of a single Hooke's joint be eliminated?
Answer: (D) By using two Hooke's joints arranged correctly (double Hooke's joint)
The angular velocity ratio of a single joint fluctuates.
Which coupling connects two parallel shafts with a small lateral offset?
Answer: (B) Oldham's coupling
It is an inversion of the double slider crank chain.
Why are flexible couplings used?
Answer: (A) To absorb shock and accommodate slight misalignment between shafts
Rubber bushes are often used.
What is the length of an open belt in terms of pulley radii r₁ and r₂ and centre distance x (approximate)?
Answer: (C) π(r₁ + r₂) + 2x + (r₁ − r₂)²/x
For a crossed belt, the last term is (r₁ + r₂)²/x.
What is centrifugal tension in a belt?
Answer: (C) The extra tension caused by centrifugal force on the belt as it passes round the pulley
Tc = mv², where m is mass per unit length.
What is the circular pitch of a gear?
Answer: (B) The distance along the pitch circle between corresponding points of adjacent teeth
p = πD/T = πm.
What is the addendum of a standard involute gear tooth?
Answer: (D) One module
The dedendum is usually 1.25 modules.
What is the speed ratio of a gear pair with 20 teeth on the driver and 60 teeth on the driven gear?
Answer: (C) 3:1 (the driven gear runs at one-third the driver speed)
N₁/N₂ = T₂/T₁ = 60/20.
What is backlash in gears?
Answer: (A) The clearance between mating teeth measured along the pitch circle
Some backlash is needed for lubrication and thermal expansion.
What is contact ratio of a gear pair?
Answer: (B) The average number of pairs of teeth in contact during meshing
A contact ratio above 1 ensures continuous contact.
What is the main advantage of a worm drive in lifting machines?
Answer: (A) It can be self-locking, so the load cannot drive the worm backwards
Self-locking worm drives have efficiency below 50%.