Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Theory of Machines: Cams

Mechanical Engineering · Theory of Machines

28 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is a cam?

  1. A coupling
  2. A rotating or sliding machine element that gives a prescribed motion to a follower by direct contact
  3. A type of gear
  4. A spring
Show answer & solution

Answer: (B) A rotating or sliding machine element that gives a prescribed motion to a follower by direct contact

Cams are used to operate engine valves.

Question 2

What is the base circle of a cam?

  1. The circle through the pitch point
  2. The largest circle on the cam
  3. The smallest circle that can be drawn to the cam profile from the cam centre
  4. The circle traced by the roller centre
Show answer & solution

Answer: (C) The smallest circle that can be drawn to the cam profile from the cam centre

The size of a cam depends on its base circle.

Question 3

What is the prime circle of a cam?

  1. The smallest circle drawn from the cam centre to the pitch curve
  2. The outer circle
  3. The circle through the pitch point
  4. The base circle
Show answer & solution

Answer: (A) The smallest circle drawn from the cam centre to the pitch curve

For a knife-edge follower, it equals the base circle.

Question 4

What is the pitch point of a cam?

  1. The lowest point of the follower
  2. Any point on the cam profile
  3. The point on the pitch curve where the pressure angle is maximum
  4. The centre of the cam
Show answer & solution

Answer: (C) The point on the pitch curve where the pressure angle is maximum

The pitch circle passes through this point.

Question 5

What is the pressure angle of a cam?

  1. The angle of dwell
  2. The angle between the direction of follower motion and the normal to the pitch curve
  3. The angle of descent
  4. The angle of rotation of the cam
Show answer & solution

Answer: (B) The angle between the direction of follower motion and the normal to the pitch curve

A large pressure angle causes side thrust and jamming.

Question 6

What is the usual maximum pressure angle allowed for a cam with a translating follower?

  1. 10°
  2. 30°
  3. 50°
  4. 70°
Show answer & solution

Answer: (B) 30°

Larger angles increase side thrust on the follower.

Question 7

For the same lift and angle of ascent, what does a smaller base circle give?

  1. A larger pressure angle
  2. A smaller pressure angle
  3. Zero pressure angle
  4. No change in pressure angle
Show answer & solution

Answer: (A) A larger pressure angle

A larger cam reduces pressure angle but increases size.

Question 8

What is the angle of ascent of a cam?

  1. The angle while the follower returns
  2. The total angle of the cam
  3. The angle while the follower stays at rest
  4. The angle turned by the cam while the follower rises from its lowest to its highest position
Show answer & solution

Answer: (D) The angle turned by the cam while the follower rises from its lowest to its highest position

The angle of descent is the corresponding angle on the return.

Question 9

What is the angle of dwell of a cam?

  1. The angle while the follower falls
  2. The pressure angle
  3. The angle while the follower rises
  4. The angle through which the cam rotates while the follower remains at rest
Show answer & solution

Answer: (D) The angle through which the cam rotates while the follower remains at rest

Dwell may occur at the highest or lowest position.

Question 10

What is the angle of action of a cam?

  1. The angle moved by the cam from the start of ascent to the end of descent
  2. The angle of ascent only
  3. The angle of dwell only
  4. The pressure angle
Show answer & solution

Answer: (A) The angle moved by the cam from the start of ascent to the end of descent

It includes any dwell at the top position.

Question 11

What types of motion can a cam mechanism impart to the follower?

  1. Only rotating motion
  2. Only continuous rotation
  3. Reciprocating or oscillating motion
  4. No motion
Show answer & solution

Answer: (C) Reciprocating or oscillating motion

Cam mechanisms usually have three links.

Question 12

How many links does a simple cam mechanism have?

  1. Two
  2. Three: cam, follower and frame
  3. Four
  4. Six
Show answer & solution

Answer: (B) Three: cam, follower and frame

The cam and follower form a higher pair.

Question 13

What are the common types of cam followers?

  1. Leaf and coil followers
  2. Open and crossed followers
  3. Spur, helical and bevel followers
  4. Knife-edge, roller, flat-faced and spherical-faced followers
Show answer & solution

Answer: (D) Knife-edge, roller, flat-faced and spherical-faced followers

Roller followers reduce wear.

Question 14

Why is a roller follower preferred to a knife-edge follower?

  1. It has less wear and friction because of rolling contact
  2. It needs no lubrication
  3. It is simpler to make
  4. It gives exact motion
Show answer & solution

Answer: (A) It has less wear and friction because of rolling contact

Knife-edge followers wear quickly.

Question 15

Which type of follower is commonly used in automobile engine valve mechanisms?

  1. Knife-edge follower
  2. Roller follower only
  3. Flat-faced (mushroom) follower
  4. Spherical follower
Show answer & solution

Answer: (C) Flat-faced (mushroom) follower

Its large contact surface reduces stress.

Question 16

For a cam with simple harmonic follower motion, where is the follower acceleration maximum?

  1. At mid-stroke
  2. It is zero everywhere
  3. It is constant
  4. At the beginning and end of the stroke
Show answer & solution

Answer: (D) At the beginning and end of the stroke

At mid-stroke, acceleration is zero and velocity is maximum.

Question 17

What does the acceleration diagram of a follower with simple harmonic motion look like?

  1. A cosine curve
  2. A straight line
  3. A step function
  4. A parabola
Show answer & solution

Answer: (A) A cosine curve

Displacement follows a cosine and velocity a sine curve.

Question 18

Which follower motion gives no sudden change in acceleration and is best for high-speed cams?

  1. Simple harmonic motion
  2. Uniform velocity
  3. Cycloidal motion
  4. Uniform acceleration and retardation
Show answer & solution

Answer: (C) Cycloidal motion

Uniform velocity motion gives infinite acceleration at the ends.

Question 19

Why is uniform velocity follower motion unsuitable at high speed?

  1. It causes no motion
  2. It causes infinite acceleration and shock at the start and end of the stroke
  3. It needs a large base circle
  4. It is too slow
Show answer & solution

Answer: (B) It causes infinite acceleration and shock at the start and end of the stroke

In practice, the ends are modified with curves.

Question 20

What is a tangent cam?

  1. A cam with circular flanks
  2. A cylindrical cam
  3. A face cam
  4. A cam whose flanks are straight lines tangent to the base circle and nose circle
Show answer & solution

Answer: (D) A cam whose flanks are straight lines tangent to the base circle and nose circle

Circular arc cams have curved flanks.

Question 21

What is a cylindrical cam?

  1. A wedge cam
  2. A cam in which the follower moves parallel to the cam axis, guided by a groove on a cylinder
  3. A tangent cam
  4. A disc cam
Show answer & solution

Answer: (B) A cam in which the follower moves parallel to the cam axis, guided by a groove on a cylinder

It is used in some machine tools.

Question 22

On which factors does the pressure angle of a cam depend?

  1. Only the follower weight
  2. Only the cam material
  3. Base circle size, follower lift, angle of ascent and follower offset
  4. Only the cam speed
Show answer & solution

Answer: (C) Base circle size, follower lift, angle of ascent and follower offset

Increasing the base circle reduces pressure angle.

Question 23

What is jump of a follower?

  1. Loss of contact between cam and follower at high speed
  2. Dwell of the follower
  3. Normal motion of the follower
  4. Rotation of the cam
Show answer & solution

Answer: (A) Loss of contact between cam and follower at high speed

A stronger spring prevents jump.

Question 24

Which cam profile curve is traced by the centre of the roller of a roller follower?

  1. Cam profile
  2. Prime circle
  3. Pitch curve
  4. Base circle
Show answer & solution

Answer: (C) Pitch curve

The actual cam profile is offset from the pitch curve by the roller radius.

Question 25

What is the stroke (lift) of a cam follower?

  1. The angle of dwell
  2. The radius of the roller
  3. The diameter of the base circle
  4. The maximum distance moved by the follower from its lowest to highest position
Show answer & solution

Answer: (D) The maximum distance moved by the follower from its lowest to highest position

It equals the difference between the largest and smallest radii of the pitch curve.

Question 26

Why are offset followers sometimes used?

  1. To make the cam larger
  2. To increase friction
  3. To reduce the pressure angle during the rise
  4. To reduce lift
Show answer & solution

Answer: (C) To reduce the pressure angle during the rise

Offset changes the geometry of contact.

Question 27

What type of follower motion is used when the follower must rise at constant speed?

  1. Parabolic motion only
  2. Cycloidal motion
  3. Simple harmonic motion
  4. Uniform velocity motion
Show answer & solution

Answer: (D) Uniform velocity motion

It needs modification at the ends to avoid shock.

Question 28

What is the purpose of the spring in a cam–follower mechanism with an open pair?

  1. To keep the follower in contact with the cam
  2. To reduce lift
  3. To increase speed
  4. To lubricate the cam
Show answer & solution

Answer: (A) To keep the follower in contact with the cam

Too weak a spring allows the follower to jump.

Practice these 28 questions interactively →