Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Theory of Machines: Balancing and Vibrations

Mechanical Engineering · Theory of Machines

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Why is balancing of rotating parts necessary?

  1. Unbalanced masses produce centrifugal forces that cause vibration, noise and bearing loads
  2. To increase weight
  3. To increase friction
  4. To reduce speed
Show answer & solution

Answer: (A) Unbalanced masses produce centrifugal forces that cause vibration, noise and bearing loads

Unbalanced forces increase with the square of speed.

Question 2

What is static balancing of rotating masses?

  1. Making the shaft stationary
  2. Making all masses equal
  3. Making the sum of couples zero only
  4. Making the vector sum of centrifugal forces (Σmr) zero
Show answer & solution

Answer: (D) Making the vector sum of centrifugal forces (Σmr) zero

A statically balanced rotor stays at rest in any position.

Question 3

What are the conditions for complete (dynamic) balancing of several masses rotating in different planes?

  1. Both the resultant force (Σmr) and the resultant couple (Σmrl) must be zero
  2. Only the resultant force must be zero
  3. Only the resultant couple must be zero
  4. All masses must be equal
Show answer & solution

Answer: (A) Both the resultant force (Σmr) and the resultant couple (Σmrl) must be zero

Two balancing masses in two planes can achieve this.

Question 4

Why can reciprocating masses not be completely balanced by rotating masses?

  1. They move too slowly
  2. They do not move
  3. They have no mass
  4. Balancing the force in the line of stroke introduces an unbalanced force at right angles
Show answer & solution

Answer: (D) Balancing the force in the line of stroke introduces an unbalanced force at right angles

Only partial balancing is possible.

Question 5

What is the primary unbalanced force of reciprocating masses?

  1. mω²r cos 2θ/n
  2. mωr
  3. mω²r cos θ
  4. mω²r sin θ
Show answer & solution

Answer: (C) mω²r cos θ

It varies at crank speed.

Question 6

At what frequency does the secondary unbalanced force of reciprocating masses vary?

  1. Four times the crank speed
  2. Twice the crank speed
  3. Equal to crank speed
  4. Half the crank speed
Show answer & solution

Answer: (B) Twice the crank speed

Secondary force = mω²r cos 2θ/n.

Question 7

What is hammer blow in locomotives?

  1. The pull on the drawbar
  2. The impact of the train on curves
  3. The maximum vertical unbalanced force on the rails due to balancing masses
  4. The noise of the engine
Show answer & solution

Answer: (C) The maximum vertical unbalanced force on the rails due to balancing masses

It may damage rails and bridges.

Question 8

What is swaying couple in locomotives?

  1. The couple causing rotation of wheels
  2. The couple due to unbalanced primary forces in two cylinders that makes the engine sway about a vertical axis
  3. The braking couple
  4. The steering couple
Show answer & solution

Answer: (B) The couple due to unbalanced primary forces in two cylinders that makes the engine sway about a vertical axis

It is caused by the cylinder centre distance.

Question 9

What is variation of tractive effort in locomotives?

  1. Fluctuation in the pulling force due to unbalanced primary forces
  2. Variation in rail friction
  3. Variation in fuel supply
  4. Variation in steam pressure only
Show answer & solution

Answer: (A) Fluctuation in the pulling force due to unbalanced primary forces

It causes jerky pulling.

Question 10

What is free vibration?

  1. Vibration due to a periodic force
  2. Vibration with damping only
  3. Vibration at resonance
  4. Vibration of a system after an initial disturbance, with no external force acting
Show answer & solution

Answer: (D) Vibration of a system after an initial disturbance, with no external force acting

It occurs at the natural frequency.

Question 11

What is forced vibration?

  1. Vibration after initial disturbance only
  2. Vibration caused by an external periodic force
  3. Vibration of a free body only
  4. Vibration without force
Show answer & solution

Answer: (B) Vibration caused by an external periodic force

The system vibrates at the forcing frequency.

Question 12

What is the natural frequency of a spring–mass system with stiffness k and mass m?

  1. (1/2π)√(k/m)
  2. k/m
  3. 2π√(k/m)
  4. (1/2π)√(m/k)
Show answer & solution

Answer: (A) (1/2π)√(k/m)

In rad/s, ωn = √(k/m).

Question 13

What is the natural frequency (in Hz) of a system in terms of static deflection δ (in m)?

  1. √δ
  2. 2π/δ
  3. 1/δ
  4. 0.4985/√δ
Show answer & solution

Answer: (D) 0.4985/√δ

It comes from fn = (1/2π)√(g/δ).

Question 14

What is resonance?

  1. The condition of free vibration only
  2. The condition of critical damping
  3. The condition when the forcing frequency equals the natural frequency, giving very large amplitudes
  4. The condition of zero vibration
Show answer & solution

Answer: (C) The condition when the forcing frequency equals the natural frequency, giving very large amplitudes

Resonance can cause failure of machines and structures.

Question 15

What are the three types of free vibration based on the motion of particles?

  1. Simple, compound and complex
  2. Linear, angular and circular
  3. Longitudinal, transverse and torsional
  4. Free, forced and damped
Show answer & solution

Answer: (C) Longitudinal, transverse and torsional

Torsional vibration occurs in shafts.

Question 16

What is the critical (whirling) speed of a shaft?

  1. The speed at which a shaft breaks under torque
  2. The maximum speed of a motor
  3. The speed of zero vibration
  4. The speed at which the shaft rotates at its natural frequency of transverse vibration, causing large deflections
Show answer & solution

Answer: (D) The speed at which the shaft rotates at its natural frequency of transverse vibration, causing large deflections

Shafts must operate away from critical speeds.

Question 17

What is critical damping?

  1. Damping that causes resonance
  2. The minimum damping that prevents oscillation of a system after disturbance
  3. Very light damping
  4. Zero damping
Show answer & solution

Answer: (B) The minimum damping that prevents oscillation of a system after disturbance

An overdamped system returns slowly without oscillating.

Question 18

What is the damping ratio?

  1. The ratio of actual damping coefficient to critical damping coefficient
  2. The ratio of force to displacement
  3. The ratio of amplitude to frequency
  4. The ratio of mass to stiffness
Show answer & solution

Answer: (A) The ratio of actual damping coefficient to critical damping coefficient

A damping ratio less than 1 means underdamped vibration.

Question 19

What is logarithmic decrement?

  1. The amplitude at resonance
  2. The damping coefficient
  3. The frequency ratio
  4. The natural logarithm of the ratio of two successive amplitudes of a damped vibration
Show answer & solution

Answer: (D) The natural logarithm of the ratio of two successive amplitudes of a damped vibration

It measures the rate of decay of oscillations.

Question 20

For vibration isolation, what must the ratio of forcing frequency to natural frequency be?

  1. Greater than √2
  2. Equal to 0
  3. Less than 1
  4. Equal to 1
Show answer & solution

Answer: (A) Greater than √2

The transmissibility is then less than 1.

Question 21

What is transmissibility?

  1. The ratio of mass to stiffness
  2. The ratio of force transmitted to the foundation to the applied force
  3. The ratio of speeds
  4. The ratio of amplitudes in free vibration
Show answer & solution

Answer: (B) The ratio of force transmitted to the foundation to the applied force

Isolators aim to reduce transmissibility.

Question 22

Which method gives an approximate natural frequency of a shaft carrying several loads?

  1. Macaulay's method
  2. Mohr's method
  3. Dunkerley's method
  4. Klein's construction
Show answer & solution

Answer: (C) Dunkerley's method

Rayleigh's energy method is another approximation.

Question 23

In torsional vibration of a two-rotor system, what is the node?

  1. The bearing location
  2. The point on the shaft where angular amplitude is zero
  3. The point of maximum twist
  4. The location of the heavier rotor
Show answer & solution

Answer: (B) The point on the shaft where angular amplitude is zero

The two rotors vibrate in opposite directions.

Question 24

What is the gyroscopic couple acting on a spinning body precessing at angular velocity ωp?

  1. Iω²
  2. Iωp/ω
  3. Iωωp
  4. ½Iω²
Show answer & solution

Answer: (C) Iωωp

I is moment of inertia and ω spin velocity.

Question 25

What effect does the gyroscopic couple of a ship's turbine rotor have when the ship pitches?

  1. It stops the ship
  2. It has no effect
  3. It makes the ship roll
  4. It makes the ship turn (yaw) to port or starboard
Show answer & solution

Answer: (D) It makes the ship turn (yaw) to port or starboard

The direction depends on the rotor's spin direction.

Question 26

Why does rolling of a ship produce no gyroscopic effect from its turbine rotor?

  1. The axis of rolling is parallel to the axis of spin
  2. Rolling is too slow
  3. Rolling stops the rotor
  4. The rotor is too light
Show answer & solution

Answer: (A) The axis of rolling is parallel to the axis of spin

A gyroscopic couple requires precession about an axis perpendicular to spin.

Question 27

What gyroscopic effect occurs when an aeroplane with a clockwise propeller (viewed from the rear) turns left?

  1. There is no effect
  2. The nose tends to rise
  3. The nose tends to fall
  4. The plane rolls
Show answer & solution

Answer: (B) The nose tends to rise

For a right turn, the nose tends to dip.

Question 28

Why is the gyroscopic effect important for two-wheelers?

  1. It has no importance
  2. It increases speed
  3. It reduces fuel consumption
  4. The gyroscopic couple of the wheels affects balance and leaning on turns
Show answer & solution

Answer: (D) The gyroscopic couple of the wheels affects balance and leaning on turns

Riders lean to balance both gyroscopic and centrifugal couples.

Question 29

What is the natural frequency of a spring–mass system with k = 1600 N/m and m = 4 kg?

  1. About 0.32 Hz
  2. About 3.18 Hz
  3. About 20 Hz
  4. About 400 Hz
Show answer & solution

Answer: (B) About 3.18 Hz

ωn = √(1600/4) = 20 rad/s; fn = 20/2π ≈ 3.18 Hz.

Question 30

What happens to the natural frequency of a spring–mass system if the mass is increased four times?

  1. It halves
  2. It becomes four times
  3. It doubles
  4. It stays the same
Show answer & solution

Answer: (A) It halves

f ∝ √(k/m).

Question 31

What happens to the natural frequency of a spring–mass system if the spring stiffness is doubled?

  1. It doubles
  2. It halves
  3. It increases by a factor of √2
  4. It stays the same
Show answer & solution

Answer: (C) It increases by a factor of √2

f ∝ √k.

Question 32

What is the effect of damping on the natural frequency of a system?

  1. It greatly increases the frequency
  2. It has no effect at all
  3. It makes the frequency infinite
  4. It slightly reduces the frequency of vibration (damped natural frequency)
Show answer & solution

Answer: (D) It slightly reduces the frequency of vibration (damped natural frequency)

ωd = ωn√(1 − ζ²).

Question 33

How does an overdamped system behave after being disturbed?

  1. It returns slowly to equilibrium without oscillating
  2. It oscillates at constant amplitude
  3. It oscillates with growing amplitude
  4. It never returns to equilibrium
Show answer & solution

Answer: (A) It returns slowly to equilibrium without oscillating

Critically damped systems return fastest without oscillating.

Question 34

What is the purpose of a vibration absorber (dynamic absorber)?

  1. To measure frequency
  2. To balance rotors
  3. To add an auxiliary mass–spring system that reduces vibration of the main system at a particular frequency
  4. To increase vibration
Show answer & solution

Answer: (C) To add an auxiliary mass–spring system that reduces vibration of the main system at a particular frequency

It is tuned to the troublesome forcing frequency.

Question 35

What is a two-plane balancing machine used for?

  1. Measuring torque
  2. Testing hardness
  3. Measuring speed
  4. Dynamic balancing of rotors such as crankshafts and armatures
Show answer & solution

Answer: (D) Dynamic balancing of rotors such as crankshafts and armatures

Correction masses are added or removed in two planes.

Question 36

Which engine arrangement is inherently well balanced for primary and secondary forces and couples?

  1. Single-cylinder engine
  2. Six-cylinder in-line engine
  3. Three-cylinder engine with no counterweights
  4. Two-cylinder in-line engine
Show answer & solution

Answer: (B) Six-cylinder in-line engine

Its crank arrangement cancels primary and secondary effects.

Question 37

What is the direct and reverse crank method used for?

  1. Analysing secondary forces in reciprocating engines and radial engines
  2. Finding belt tensions
  3. Calculating gear ratios
  4. Designing cams
Show answer & solution

Answer: (A) Analysing secondary forces in reciprocating engines and radial engines

Imaginary cranks rotating in opposite directions represent the forces.

Question 38

What is the critical speed of a shaft in terms of static deflection δ (in m)?

  1. About √δ rps
  2. About 1/δ rps
  3. About 0.4985/√δ revolutions per second
  4. About δ² rps
Show answer & solution

Answer: (C) About 0.4985/√δ revolutions per second

It equals the natural frequency of transverse vibration.

Practice these 38 questions interactively →