Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Strength of Materials: Torsion and Cylinders

Mechanical Engineering · Strength of Materials

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is torsion?

  1. Bending under load
  2. Axial tension
  3. Axial compression
  4. Twisting of a shaft or member by an applied couple (torque)
Show answer & solution

Answer: (D) Twisting of a shaft or member by an applied couple (torque)

Shafts transmitting power are in torsion.

Question 2

What is the torsion equation for a circular shaft?

  1. P = π²EI/L²
  2. T/J = τ/r = Gθ/L
  3. M/I = σ/y = E/R
  4. σ = P/A
Show answer & solution

Answer: (B) T/J = τ/r = Gθ/L

T is torque, J is polar moment of inertia and θ is angle of twist.

Question 3

How does shear stress vary across a solid circular shaft under torsion?

  1. From zero at the centre to maximum at the outer surface
  2. Maximum at the centre
  3. Maximum at mid-radius
  4. Uniform across the section
Show answer & solution

Answer: (A) From zero at the centre to maximum at the outer surface

τ is directly proportional to radius.

Question 4

What is the maximum shear stress in a solid shaft of diameter d transmitting torque T?

  1. 32T/πd³
  2. 4T/πd²
  3. 16T/πd³
  4. T/πd²
Show answer & solution

Answer: (C) 16T/πd³

It occurs at the outer surface.

Question 5

What is torsional rigidity of a shaft?

  1. The elastic limit in torsion
  2. The torque required to produce a twist of one radian per unit length (GJ)
  3. The number of cycles to failure
  4. The maximum torque a shaft can transmit
Show answer & solution

Answer: (B) The torque required to produce a twist of one radian per unit length (GJ)

A higher GJ means less twist.

Question 6

What is the power transmitted by a shaft rotating at N rpm with torque T?

  1. πNT
  2. 2πT/N
  3. 2πNT/60
  4. NT/60
Show answer & solution

Answer: (C) 2πNT/60

P is in watts when T is in N·m.

Question 7

Why is a hollow shaft preferred to a solid shaft of the same weight?

  1. It can transmit greater torque because material is placed farther from the centre
  2. It is cheaper to make
  3. It has a smaller outer diameter
  4. It needs no bearings
Show answer & solution

Answer: (A) It can transmit greater torque because material is placed farther from the centre

Material near the centre carries little stress.

Question 8

For two shafts connected in series, which quantity is the same in both?

  1. Shear stress
  2. Diameter
  3. Angle of twist
  4. Torque
Show answer & solution

Answer: (D) Torque

The total angle of twist is the sum of the individual twists.

Question 9

For two shafts connected in parallel (rigidly joined at both ends), which quantity is the same in both?

  1. Diameter
  2. Angle of twist
  3. Shear stress
  4. Torque
Show answer & solution

Answer: (B) Angle of twist

The total torque is shared between the shafts.

Question 10

What is the safe torque for a compound shaft made of two materials?

  1. The mean of the two values
  2. The larger of the two values
  3. The sum of the two values
  4. The smaller of the values calculated for each material
Show answer & solution

Answer: (D) The smaller of the values calculated for each material

Neither material may exceed its permissible stress.

Question 11

When is a cylinder considered thin?

  1. When it is made of thin sheet metal only
  2. When it is very long
  3. When its wall thickness is less than about one-twentieth of its diameter
  4. When its wall thickness is more than its diameter
Show answer & solution

Answer: (C) When its wall thickness is less than about one-twentieth of its diameter

Stresses are then assumed uniform across the wall.

Question 12

What is hoop (circumferential) stress in a thin cylinder?

  1. Stress acting along the circumference, tending to split the cylinder along its length
  2. Stress acting along the axis
  3. Shear stress only
  4. Stress acting radially
Show answer & solution

Answer: (A) Stress acting along the circumference, tending to split the cylinder along its length

σ_h = pd/2t.

Question 13

What is longitudinal stress in a thin cylinder?

  1. Radial stress
  2. Shear stress only
  3. Stress acting along the axis, tending to split the cylinder across its section
  4. Stress along the circumference
Show answer & solution

Answer: (C) Stress acting along the axis, tending to split the cylinder across its section

σ_l = pd/4t.

Question 14

How does longitudinal stress in a thin cylinder compare with hoop stress?

  1. It is half of the hoop stress
  2. It is one-quarter of the hoop stress
  3. It is twice the hoop stress
  4. It is equal to the hoop stress
Show answer & solution

Answer: (A) It is half of the hoop stress

This is why thin cylinders tend to fail along their length.

Question 15

What is the hoop stress in a boiler shell of 200 cm diameter and 1.5 cm wall thickness under an internal pressure of 1.5 MN/m²?

  1. 30 MN/m²
  2. 50 MN/m²
  3. 100 MN/m²
  4. 200 MN/m²
Show answer & solution

Answer: (C) 100 MN/m²

σ_h = pd/2t = 1.5 × 200 ÷ 3 = 100 MN/m².

Question 16

What is the stress in a thin spherical shell under internal pressure?

  1. pd/t
  2. pd/4t in all directions
  3. pd/2t
  4. pd/8t
Show answer & solution

Answer: (B) pd/4t in all directions

A sphere is the most efficient shape for a pressure vessel.

Question 17

Which equations are used to analyse stresses in thick cylinders?

  1. Bernoulli's equation
  2. Euler's equations
  3. Macaulay's equations
  4. Lamé's equations
Show answer & solution

Answer: (D) Lamé's equations

Hoop stress varies across the wall in thick cylinders.

Question 18

What is a seamless cylinder?

  1. A cylinder made without any joint
  2. A cylinder with riveted joints
  3. A cylinder with welded joints
  4. A cylinder with bolted joints
Show answer & solution

Answer: (A) A cylinder made without any joint

Gas cylinders are often seamless.

Question 19

What are principal stresses?

  1. The stresses due to torsion only
  2. The maximum and minimum normal stresses on planes where shear stress is zero
  3. The average stresses
  4. The stresses at the yield point
Show answer & solution

Answer: (B) The maximum and minimum normal stresses on planes where shear stress is zero

They act on principal planes.

Question 20

At what angle to each other are principal planes?

  1. 30°
  2. 45°
  3. 60°
  4. 90°
Show answer & solution

Answer: (D) 90°

Maximum shear stress occurs on planes at 45° to principal planes.

Question 21

What is the maximum shear stress in terms of principal stresses σ₁ and σ₂ (in two dimensions)?

  1. (σ₁ − σ₂)/2
  2. σ₁σ₂
  3. (σ₁ + σ₂)/2
  4. σ₁ − σ₂
Show answer & solution

Answer: (A) (σ₁ − σ₂)/2

It is the radius of Mohr's circle.

Question 22

What is Mohr's circle used for?

  1. Finding buckling loads
  2. Finding deflection of beams
  3. Graphically finding normal and shear stresses on any plane, including principal stresses
  4. Finding torque in shafts
Show answer & solution

Answer: (C) Graphically finding normal and shear stresses on any plane, including principal stresses

It was introduced by Otto Mohr.

Question 23

Which theory of failure is most suitable for brittle materials?

  1. Maximum strain energy theory
  2. Maximum principal stress theory (Rankine)
  3. Maximum distortion energy theory
  4. Maximum shear stress theory
Show answer & solution

Answer: (B) Maximum principal stress theory (Rankine)

Brittle materials fail when the largest principal stress reaches the ultimate stress.

Question 24

Which theory of failure is commonly used for ductile materials and gives conservative results?

  1. Maximum principal stress theory
  2. Maximum strain energy theory (Beltrami)
  3. Maximum principal strain theory
  4. Maximum shear stress theory (Guest–Tresca)
Show answer & solution

Answer: (D) Maximum shear stress theory (Guest–Tresca)

The distortion energy (von Mises) theory is the most accurate for ductile materials.

Question 25

What is a closely coiled helical spring mainly subjected to?

  1. Axial compression only
  2. Torsional shear stress
  3. Pure bending
  4. Tensile stress only
Show answer & solution

Answer: (B) Torsional shear stress

The wire twists as the spring is loaded.

Question 26

What is the deflection of a closely coiled helical spring of mean coil diameter D, wire diameter d and n turns under load W?

  1. WD/Gd
  2. 8WDn/(Gd³)
  3. 8WD³n/(Gd⁴)
  4. WD³n/(Gd⁴)
Show answer & solution

Answer: (C) 8WD³n/(Gd⁴)

G is the modulus of rigidity of the wire.

Question 27

What is the stiffness of two springs of stiffness k₁ and k₂ connected in series?

  1. k₁k₂/(k₁ + k₂)
  2. k₁ + k₂
  3. (k₁ + k₂)/2
  4. k₁ − k₂
Show answer & solution

Answer: (A) k₁k₂/(k₁ + k₂)

For springs in parallel, stiffness is k₁ + k₂.

Question 28

What type of spring is commonly used in the suspension of trucks and railway wagons?

  1. Torsion spring
  2. Spiral watch spring
  3. Closely coiled helical spring
  4. Laminated (leaf) spring
Show answer & solution

Answer: (D) Laminated (leaf) spring

It is also called a carriage spring.

Question 29

What are the main ways in which a riveted joint can fail?

  1. Fatigue of the head only
  2. Buckling of the rivets
  3. Bending of the plate only
  4. Tearing of the plate, shearing of the rivets and crushing of the rivets or plate
Show answer & solution

Answer: (D) Tearing of the plate, shearing of the rivets and crushing of the rivets or plate

The weakest mode decides the joint's strength.

Question 30

What is a chain riveted joint?

  1. A joint with staggered rivets
  2. A joint with one rivet in the outer row
  3. A joint in which rivets in adjacent rows are directly opposite each other
  4. A welded joint
Show answer & solution

Answer: (C) A joint in which rivets in adjacent rows are directly opposite each other

In zig-zag riveting, rivets in adjacent rows are staggered.

Question 31

What is diamond riveting?

  1. A welded joint shape
  2. An arrangement in which rivets are staggered and the number decreases from the inner row to a single rivet in the outer row
  3. An arrangement with rivets opposite each other
  4. A single row of rivets
Show answer & solution

Answer: (B) An arrangement in which rivets are staggered and the number decreases from the inner row to a single rivet in the outer row

It is used in butt joints and gives high efficiency.

Question 32

What is the diagonal pitch of a zig-zag riveted joint?

  1. The distance from rivet to plate edge
  2. The distance between rivets in the same row
  3. The distance between centres of rivets in adjacent rows
  4. The distance between rows
Show answer & solution

Answer: (C) The distance between centres of rivets in adjacent rows

The distance between rows is called the back pitch.

Question 33

On which diameter are the stresses in riveted boiler joints calculated?

  1. The shank diameter of the rivet
  2. The diameter of the drilled or reamed hole
  3. The head diameter
  4. The average of rivet and hole diameters
Show answer & solution

Answer: (B) The diameter of the drilled or reamed hole

The rivet fills the hole after being driven.

Question 34

Why are rivets made of ductile materials?

  1. They must be formed into heads without cracking
  2. They must be very hard
  3. They must be brittle
  4. They must resist heat only
Show answer & solution

Answer: (A) They must be formed into heads without cracking

Mild steel is the usual rivet material.

Question 35

What is the maximum shear stress in a hollow shaft of outer diameter D and inner diameter d transmitting torque T?

  1. 16T/πD³
  2. T/π(D − d)
  3. 32T/πD³
  4. 16TD/[π(D⁴ − d⁴)]
Show answer & solution

Answer: (D) 16TD/[π(D⁴ − d⁴)]

The polar moment of inertia is π(D⁴ − d⁴)/32.

Question 36

What is the angle of twist of a shaft of length L under torque T?

  1. T/GJL
  2. TL/GJ
  3. GL/TJ
  4. TJ/GL
Show answer & solution

Answer: (B) TL/GJ

θ is in radians.

Question 37

What is the maximum principal stress in a shaft under combined bending moment M and torque T (solid shaft, diameter d)?

  1. (16/πd³)[M + √(M² + T²)]
  2. 32M/πd³
  3. 16T/πd³
  4. (16/πd³)(M + T)
Show answer & solution

Answer: (A) (16/πd³)[M + √(M² + T²)]

The equivalent bending moment is ½[M + √(M² + T²)].

Question 38

What is the hoop stress in a thin spherical shell compared with that in a thin cylinder of the same diameter, thickness and pressure?

  1. Twice
  2. Half
  3. One-quarter
  4. Equal
Show answer & solution

Answer: (B) Half

σ_sphere = pd/4t, while σ_hoop,cylinder = pd/2t.

Question 39

What is the usual margin (edge distance) of a rivet from the edge of a plate?

  1. About 5 times the rivet diameter
  2. Zero
  3. About 1.5 times the rivet diameter
  4. Equal to the plate thickness
Show answer & solution

Answer: (C) About 1.5 times the rivet diameter

Too small a margin may cause the plate to tear at the edge.

Practice these 39 questions interactively →