What is elasticity?
Show answer & solution
Answer: (C) The property by which a material returns to its original shape after the load is removed
It holds up to the elastic limit.
Mechanical Engineering · Strength of Materials
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is elasticity?
Answer: (C) The property by which a material returns to its original shape after the load is removed
It holds up to the elastic limit.
What is plasticity?
Answer: (C) The property by which a material undergoes permanent deformation without fracture
Plasticity is used in forging and rolling.
What is ductility?
Answer: (A) The property by which a material can be drawn into wires (thin sections) under tension
Copper and mild steel are highly ductile.
What is brittleness?
Answer: (B) The property of breaking with little or no plastic deformation
Cast iron and glass are brittle.
What is toughness?
Answer: (D) The ability of a material to absorb a large amount of energy before fracture
It is indicated by the area under the stress–strain curve up to fracture.
What is hardness?
Answer: (C) The resistance of a material to indentation, scratching or wear
Diamond is the hardest natural material.
What property is measured by an impact test?
Answer: (A) Toughness
Izod and Charpy tests use notched specimens.
Which material is the most elastic in the engineering sense of returning to shape under high stress?
Answer: (B) Steel
Engineering elasticity relates to a high modulus and elastic limit, not just large stretch.
Which machine is used to carry out tensile, compression and bending tests?
Answer: (B) Universal testing machine (UTM)
It applies controlled loads and records deformation.
On a stress–strain curve for mild steel, what is the yield point?
Answer: (C) The stress at which the material extends appreciably without any increase in load
Mild steel shows upper and lower yield points.
How does the stress needed to start yielding in mild steel compare with the stress needed to continue it?
Answer: (A) It is greater
This is why there is an upper and a lower yield point.
What is proof stress?
Answer: (D) The stress that produces a specified small permanent strain, such as 0.2%, used where there is no clear yield point
Aluminium and high-strength steels use 0.2% proof stress.
How does breaking stress compare with ultimate tensile stress for mild steel, calculated on the original area?
Answer: (B) Breaking stress is lower
The load falls after necking begins.
What is necking in a tensile test?
Answer: (C) Local reduction in cross-sectional area of a ductile specimen just before fracture
It begins at the ultimate load.
What is the percentage reduction in area of a cast iron specimen in a tensile test?
Answer: (A) Negligible (close to zero)
Brittle materials fracture with little necking.
What type of fracture does a mild steel specimen show in a tensile test?
Answer: (D) Cup-and-cone fracture
Brittle cast iron shows a flat, granular fracture.
What does a true stress–strain curve plot?
Answer: (D) Load divided by instantaneous area against natural (logarithmic) strain
True stress keeps rising until fracture.
What is rupture stress?
Answer: (C) Load at breaking point divided by the area of the neck
It is higher than the nominal breaking stress.
What is fatigue?
Answer: (A) Failure of a material under repeated or fluctuating stresses below its ultimate strength
Rotating shafts often fail by fatigue.
What is the endurance (fatigue) limit?
Answer: (B) The maximum stress that a material can withstand for an infinite number of stress cycles
Steels show a clear endurance limit on the S–N curve.
What is an S–N curve?
Answer: (A) A plot of stress amplitude against the number of cycles to failure
It is used in fatigue design.
What is flow stress?
Answer: (C) The stress required to continue plastic deformation of a solid
It is used in metal-forming calculations.
Which hardness test uses a hardened steel or carbide ball pressed into the surface?
Answer: (B) Brinell hardness test
The Brinell number is load divided by the curved area of indentation.
Which hardness test uses a square-based diamond pyramid indenter?
Answer: (C) Vickers hardness test
It is suitable for very hard and thin materials.
Which hardness test gives a direct reading on a dial based on depth of penetration?
Answer: (D) Rockwell hardness test
Rockwell C uses a diamond cone, and Rockwell B uses a steel ball.
Which impact test uses a specimen held vertically as a cantilever?
Answer: (A) Izod test
In the Charpy test, the specimen is supported as a simple beam.
How does the ultimate shear strength of steel compare with its ultimate tensile strength?
Answer: (B) It is roughly half to three-quarters of the tensile strength
A value of about 0.5–0.6 is often used in design.
How does the ultimate tensile strength of cast iron compare with its compressive strength?
Answer: (B) It is much lower
Cast iron is strong in compression but weak in tension.
How does the elongation of a mild steel wire behave as equal load increments are added until it breaks?
Answer: (D) It increases uniformly at first, then increases rapidly after yielding
Plastic deformation causes large extensions.
What does the area under the elastic part of a stress–strain curve represent?
Answer: (A) Modulus of resilience
The total area to fracture represents toughness.
What is the percentage elongation of a material?
Answer: (B) The increase in gauge length at fracture as a percentage of the original gauge length
It is a measure of ductility.
Which material property is improved by cold working, at the cost of ductility?
Answer: (C) Strength and hardness
This is called strain hardening or work hardening.
What is the yield point in mild steel followed by on the stress–strain curve?
Answer: (B) Strain hardening up to the ultimate stress
After yielding, more stress is needed to keep deforming the material.
Which materials do not show a distinct yield point?
Answer: (C) Aluminium, copper and high-carbon steels
For these, 0.2% proof stress is used.
What is the Brinell hardness number?
Answer: (A) The load divided by the curved surface area of the indentation
It is expressed in kgf/mm².
Why is the endurance limit important in designing rotating shafts?
Answer: (D) Shafts experience reversing bending stresses every revolution and may fail by fatigue
Design stresses are kept below the endurance limit.