Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Strength of Materials: Simple Stress and Strain

Mechanical Engineering · Strength of Materials

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is stress?

  1. The deformation of a body
  2. The total load on a body
  3. The change in length per unit length
  4. The internal resisting force per unit area of a body
Show answer & solution

Answer: (D) The internal resisting force per unit area of a body

Its SI unit is N/m² (pascal).

Question 2

What is strain?

  1. The energy stored
  2. The ratio of change in dimension to the original dimension
  3. The total load
  4. Force per unit area
Show answer & solution

Answer: (B) The ratio of change in dimension to the original dimension

It may be linear, lateral, shear or volumetric.

Question 3

Which of the following quantities has no unit?

  1. Stress
  2. Young's modulus
  3. Strain
  4. Bulk modulus
Show answer & solution

Answer: (C) Strain

Strain is a ratio of two lengths (or volumes).

Question 4

What type of stress is produced when equal and opposite forces tend to elongate a body?

  1. Tensile stress
  2. Bending stress
  3. Compressive stress
  4. Shear stress
Show answer & solution

Answer: (A) Tensile stress

Compressive stress tends to shorten a body.

Question 5

What is shear stress?

  1. Stress that elongates a body
  2. Stress due to temperature only
  3. Stress produced by forces acting parallel to a surface, tending to make one layer slide over another
  4. Stress that shortens a body
Show answer & solution

Answer: (C) Stress produced by forces acting parallel to a surface, tending to make one layer slide over another

Rivets and pins in joints are mainly in shear.

Question 6

What is linear (longitudinal) strain?

  1. Change in volume per unit volume
  2. Deformation per unit length in the direction of the applied force
  3. Deformation at right angles to the force
  4. Angular deformation
Show answer & solution

Answer: (B) Deformation per unit length in the direction of the applied force

It is the change in length divided by original length.

Question 7

What does Hooke's law state?

  1. Within the limit of proportionality, stress is directly proportional to strain
  2. Stress depends only on temperature
  3. Strain is constant
  4. Stress is inversely proportional to strain
Show answer & solution

Answer: (A) Within the limit of proportionality, stress is directly proportional to strain

The constant of proportionality is the modulus of elasticity.

Question 8

Up to which point does Hooke's law hold good?

  1. Yield point
  2. Breaking point
  3. Ultimate stress point
  4. Limit of proportionality
Show answer & solution

Answer: (D) Limit of proportionality

Beyond this point stress and strain are no longer proportional.

Question 9

What is Young's modulus (modulus of elasticity)?

  1. The ratio of shear stress to shear strain
  2. The ratio of longitudinal stress to longitudinal strain within the elastic limit
  3. The ratio of lateral strain to linear strain
  4. The ratio of volumetric stress to volumetric strain
Show answer & solution

Answer: (B) The ratio of longitudinal stress to longitudinal strain within the elastic limit

It measures the stiffness of a material.

Question 10

What is the approximate Young's modulus of mild steel?

  1. 20 GPa
  2. 70 GPa
  3. 200–210 GPa (about 2.1 × 10⁶ kg/cm²)
  4. 1000 GPa
Show answer & solution

Answer: (C) 200–210 GPa (about 2.1 × 10⁶ kg/cm²)

Aluminium has a Young's modulus of about 70 GPa.

Question 11

What happens to the Young's modulus of a wire if its radius is doubled?

  1. It remains unchanged
  2. It becomes four times
  3. It doubles
  4. It halves
Show answer & solution

Answer: (A) It remains unchanged

Young's modulus is a property of the material, not of its dimensions.

Question 12

What is the modulus of rigidity (shear modulus)?

  1. The ratio of volumetric stress to volumetric strain
  2. The ratio of longitudinal stress to longitudinal strain
  3. The ratio of lateral strain to longitudinal strain
  4. The ratio of shear stress to shear strain
Show answer & solution

Answer: (D) The ratio of shear stress to shear strain

It is denoted by G or C.

Question 13

What is the bulk modulus?

  1. The ratio of direct stress to volumetric strain when a body is subjected to three equal mutually perpendicular stresses
  2. The ratio of lateral to linear strain
  3. The ratio of longitudinal stress to longitudinal strain
  4. The ratio of shear stress to shear strain
Show answer & solution

Answer: (A) The ratio of direct stress to volumetric strain when a body is subjected to three equal mutually perpendicular stresses

It is denoted by K.

Question 14

What is Poisson's ratio?

  1. The ratio of lateral stress to longitudinal stress
  2. The ratio of lateral strain to linear (longitudinal) strain within the elastic limit
  3. The ratio of stress to strain
  4. The ratio of shear stress to shear strain
Show answer & solution

Answer: (B) The ratio of lateral strain to linear (longitudinal) strain within the elastic limit

It is denoted by ν or 1/m.

Question 15

What is the typical value of Poisson's ratio for steel?

  1. 0.01–0.1
  2. 0.25–0.33
  3. 0.4–0.6
  4. 1.0–1.5
Show answer & solution

Answer: (B) 0.25–0.33

A value of about 0.3 is commonly used.

Question 16

What is the typical value of Poisson's ratio for cast iron?

  1. 0.01–0.1
  2. 0.23–0.27
  3. 0.4–0.5
  4. 0.5–0.6
Show answer & solution

Answer: (B) 0.23–0.27

Cast iron is a brittle material with a slightly lower Poisson's ratio than steel.

Question 17

What is the maximum possible value of Poisson's ratio for an isotropic material?

  1. 0.25
  2. 0.5
  3. 1.0
  4. 2.0
Show answer & solution

Answer: (B) 0.5

A Poisson's ratio of 0.5 means the material is incompressible, like rubber.

Question 18

For which material is Poisson's ratio close to zero?

  1. Rubber
  2. Copper
  3. Steel
  4. Cork
Show answer & solution

Answer: (D) Cork

This makes cork ideal for bottle stoppers.

Question 19

How does the volumetric strain of a bar in tension change as Poisson's ratio increases?

  1. It increases
  2. It stays the same
  3. It decreases
  4. It becomes infinite
Show answer & solution

Answer: (C) It decreases

Volumetric strain = ε(1 − 2ν).

Question 20

What is the relationship between Young's modulus E, modulus of rigidity G and Poisson's ratio ν?

  1. E = G(1 + ν)
  2. E = 3G(1 − 2ν)
  3. E = G/(1 + ν)
  4. E = 2G(1 + ν)
Show answer & solution

Answer: (D) E = 2G(1 + ν)

For steel, G is roughly 0.4E.

Question 21

What is the relationship between Young's modulus E, bulk modulus K and Poisson's ratio ν?

  1. E = 3K(1 − 2ν)
  2. E = K(1 − ν)
  3. E = 2K(1 + ν)
  4. E = 3K(1 + ν)
Show answer & solution

Answer: (A) E = 3K(1 − 2ν)

When ν = 0.5, K becomes infinite.

Question 22

What is the relationship between E, G and K?

  1. E = 3KG/(K + G)
  2. E = K + G
  3. E = 9KG/(3K + G)
  4. E = 9K + G
Show answer & solution

Answer: (C) E = 9KG/(3K + G)

It links all three elastic constants.

Question 23

How many independent elastic constants does a homogeneous isotropic material have?

  1. Four
  2. One
  3. Three
  4. Two
Show answer & solution

Answer: (D) Two

The other constants can be found from any two (for example E and ν).

Question 24

What is an isotropic material?

  1. A material with only plastic behaviour
  2. A material with properties varying with direction
  3. A material with the same elastic properties in all directions
  4. A material with zero elasticity
Show answer & solution

Answer: (C) A material with the same elastic properties in all directions

Most metals are treated as isotropic.

Question 25

What is a homogeneous material?

  1. A material with the same properties at every point
  2. A material without elasticity
  3. A material made of two metals
  4. A material with the same properties in all directions
Show answer & solution

Answer: (A) A material with the same properties at every point

Homogeneity and isotropy are different properties.

Question 26

What is the elongation of a bar of length L, area A and modulus E under an axial load P?

  1. PL/AE
  2. P/AE
  3. AE/PL
  4. PA/LE
Show answer & solution

Answer: (A) PL/AE

It applies within the elastic limit.

Question 27

What is the elongation of a uniform bar hanging vertically under its own weight W?

  1. WL/4AE
  2. WL/AE
  3. WL/2AE
  4. 2WL/AE
Show answer & solution

Answer: (C) WL/2AE

It equals the elongation produced by half the weight applied at the lower end.

Question 28

The elongation of a bar due to its own weight W is compared with that of a similar bar also carrying an extra load W at its end. What is the ratio?

  1. 1:1
  2. 1:2
  3. 1:3
  4. 1:4
Show answer & solution

Answer: (C) 1:3

WL/2AE compared with WL/2AE + WL/AE = 3WL/2AE.

Question 29

In a composite bar of two materials that deform equally under axial load, how are the stresses in the two materials related?

  1. They are equal
  2. They are inversely proportional to their moduli
  3. They are independent of their moduli
  4. They are proportional to their moduli of elasticity
Show answer & solution

Answer: (D) They are proportional to their moduli of elasticity

Equal strain means σ₁/E₁ = σ₂/E₂.

Question 30

What is the principle of superposition in strength of materials?

  1. Loads cancel each other
  2. The total effect of several loads equals the sum of the effects of each load acting separately
  3. Only the largest load matters
  4. Stresses are always equal
Show answer & solution

Answer: (B) The total effect of several loads equals the sum of the effects of each load acting separately

It applies to linear elastic behaviour.

Question 31

What is the factor of safety?

  1. The ratio of strain to stress
  2. The ratio of working stress to ultimate stress
  3. The ratio of load to area
  4. The ratio of ultimate (or yield) stress to working (permissible) stress
Show answer & solution

Answer: (D) The ratio of ultimate (or yield) stress to working (permissible) stress

It allows for uncertainties in loads and materials.

Question 32

What is working (allowable) stress?

  1. The maximum stress permitted in a member under service conditions
  2. The stress at breaking
  3. The ultimate stress
  4. The yield stress
Show answer & solution

Answer: (A) The maximum stress permitted in a member under service conditions

It is the ultimate or yield stress divided by the factor of safety.

Question 33

What is the ultimate tensile strength of a material?

  1. Maximum load during the test divided by the original cross-sectional area
  2. Load at fracture divided by neck area
  3. Load at yield divided by original area
  4. Maximum load divided by area at fracture
Show answer & solution

Answer: (A) Maximum load during the test divided by the original cross-sectional area

It is the highest point on the engineering stress–strain curve.

Question 34

A specimen of 1 cm² cross-section reaches a maximum load of 8 tonnes and necks to 0.5 cm². What is its ultimate tensile strength?

  1. 4 tonnes/cm²
  2. 8 tonnes/cm²
  3. 12 tonnes/cm²
  4. 16 tonnes/cm²
Show answer & solution

Answer: (B) 8 tonnes/cm²

Ultimate strength is calculated on the original area.

Question 35

What is the volumetric strain of a rectangular bar under axial stress?

  1. ε
  2. ε(1 + 2ν)
  3. 3ε
  4. ε(1 − 2ν), where ε is the linear strain
Show answer & solution

Answer: (D) ε(1 − 2ν), where ε is the linear strain

For ν = 0.5, the volume does not change.

Question 36

What is the change in length of a steel bar 2 m long and 400 mm² in area under a 40 kN tensile load (E = 200 GPa)?

  1. 0.5 mm
  2. 1 mm
  3. 2 mm
  4. 10 mm
Show answer & solution

Answer: (B) 1 mm

δ = PL/AE = 40 000 × 2000 ÷ (400 × 200 000) = 1 mm.

Question 37

What is the stress in a bar of 500 mm² cross-section carrying an axial load of 50 kN?

  1. 10 MPa
  2. 50 MPa
  3. 100 MPa
  4. 1000 MPa
Show answer & solution

Answer: (C) 100 MPa

σ = P/A = 50 000 ÷ 500 = 100 N/mm².

Question 38

What is the elastic limit?

  1. The maximum stress up to which a material returns fully to its original shape after unloading
  2. The stress at breaking
  3. The stress at necking
  4. The maximum stress before fracture
Show answer & solution

Answer: (A) The maximum stress up to which a material returns fully to its original shape after unloading

It is slightly above the limit of proportionality in many materials.

Question 39

What is volumetric strain?

  1. The angular deformation
  2. The ratio of lateral to linear strain
  3. The ratio of change in length to original length
  4. The ratio of change in volume to original volume
Show answer & solution

Answer: (D) The ratio of change in volume to original volume

For three equal stresses, εv = 3σ(1 − 2ν)/E.

Question 40

What is shear strain?

  1. The change in volume per unit volume
  2. The change in length per unit length
  3. The angular deformation (in radians) produced by shear stress
  4. The ratio of lateral to linear strain
Show answer & solution

Answer: (C) The angular deformation (in radians) produced by shear stress

It is denoted by γ.

Practice these 40 questions interactively →