What is thermal stress?
Show answer & solution
Answer: (C) Stress developed when a body is prevented from expanding or contracting freely with temperature change
σ = EαΔT for a fully restrained bar.
Mechanical Engineering · Strength of Materials
26 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is thermal stress?
Answer: (C) Stress developed when a body is prevented from expanding or contracting freely with temperature change
σ = EαΔT for a fully restrained bar.
What stress develops in a body that is free to expand when heated?
Answer: (A) No stress
Stress arises only when expansion is restrained.
What stress develops in a bar heated while both ends are rigidly fixed?
Answer: (D) Compressive stress
It is prevented from expanding.
What stress develops in a bar cooled while both ends are rigidly fixed?
Answer: (C) Tensile stress
It is prevented from contracting.
On which factors does thermal stress in a fully restrained bar depend?
Answer: (B) Modulus of elasticity, coefficient of thermal expansion and temperature change
It does not depend on the length or area.
Why are expansion joints provided in railway tracks, bridges and pipelines?
Answer: (A) To allow for thermal expansion and avoid large thermal stresses
Long steel structures expand noticeably in Pakistan's summer heat.
What is strain energy?
Answer: (D) The energy stored in a body when it is strained within the elastic limit
It is released when the load is removed.
What is resilience?
Answer: (B) The total strain energy stored in a body
It is recovered when the load is removed.
What is proof resilience?
Answer: (C) The maximum strain energy that can be stored in a body up to the elastic limit
It equals σ²V/2E at the elastic limit.
What is modulus of resilience?
Answer: (A) Proof resilience per unit volume of material
It equals σ²/2E at the elastic limit.
When is resilience an important property of a material?
Answer: (C) When the material is subjected to shock or impact loading
Springs need high resilience.
What is the strain energy stored in a bar under a gradually applied stress σ?
Answer: (B) σ²V/2E
V is the volume of the bar.
How does the stress caused by a suddenly applied load compare with that caused by the same load applied gradually?
Answer: (A) It is twice as large
σ_sudden = 2P/A.
How does the strain energy stored by a suddenly applied load compare with that of the same load applied gradually?
Answer: (D) It is four times larger
Since energy ∝ σ², doubling stress gives four times the energy.
What is impact loading?
Answer: (B) A load that falls from a height or strikes a member with velocity
Stresses from impact can be many times greater than static stresses.
What is the thermal stress in a steel rod fully restrained at both ends when heated by 50 °C (E = 200 GPa, α = 12 × 10⁻⁶ /°C)?
Answer: (C) 120 MPa
σ = EαΔT = 200 000 × 12 × 10⁻⁶ × 50 = 120 MPa.
What is the free thermal expansion of a bar of length L for a temperature rise ΔT?
Answer: (B) αLΔT
α is the coefficient of linear expansion.
In a composite bar of steel and brass heated together, what stresses develop?
Answer: (A) Compression in the brass and tension in the steel
Brass expands more than steel, so the steel restrains it.
What is the strain energy stored in a bar due to a gradually applied load P producing extension δ?
Answer: (D) Pδ/2
Work done equals the area under the load–extension line.
What is the maximum stress produced when a load W falls through a height h onto a collar at the end of a bar, if h is large compared with extension?
Answer: (B) σ ≈ √(2WhE/AL)
Impact stresses can be very high even for small loads.
Why should members subjected to shock loads have a uniform cross-section where possible?
Answer: (C) Uniform sections store more strain energy for the same maximum stress
Stress concentrations at reduced sections lower energy absorption.
What is toughness, in terms of the stress–strain curve?
Answer: (D) The total area under the stress–strain curve up to fracture
Modulus of toughness is energy per unit volume to fracture.
What is the modulus of resilience of a material with elastic limit stress 250 MPa and E = 200 GPa?
Answer: (A) 0.156 MJ/m³
σ²/2E = 250² ÷ (2 × 200 000) ≈ 0.156 MPa = 0.156 MJ/m³.
What is the shear strain energy per unit volume due to shear stress τ?
Answer: (C) τ²/2G
G is the modulus of rigidity.
What happens to thermal stress in a fully restrained bar if its length is doubled?
Answer: (B) It stays the same
Thermal stress depends on E, α and ΔT, not on length.
Why are bimetallic strips used in thermostats?
Answer: (D) Two metals with different expansion coefficients bend when heated, operating a switch
The bending is caused by differential thermal expansion.