Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Strength of Materials: Deflection and Columns

Mechanical Engineering · Strength of Materials

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the deflection at the free end of a cantilever of length L carrying a point load W at the free end?

  1. WL³/48EI
  2. 5WL³/384EI
  3. WL³/3EI
  4. WL³/8EI
Show answer & solution

Answer: (C) WL³/3EI

EI is the flexural rigidity of the beam.

Question 2

What is the deflection at the free end of a cantilever carrying a uniformly distributed load w over its whole length L?

  1. 5wL⁴/384EI
  2. wL⁴/3EI
  3. wL⁴/48EI
  4. wL⁴/8EI
Show answer & solution

Answer: (D) wL⁴/8EI

The slope at the free end is wL³/6EI.

Question 3

What is the maximum deflection of a simply supported beam of span L carrying a central point load W?

  1. WL³/48EI
  2. WL³/3EI
  3. WL³/8EI
  4. WL³/192EI
Show answer & solution

Answer: (A) WL³/48EI

It occurs at mid-span.

Question 4

What is the maximum deflection of a simply supported beam of span L carrying a uniformly distributed load w over the whole span?

  1. wL⁴/48EI
  2. 5wL⁴/384EI
  3. wL⁴/384EI
  4. wL⁴/8EI
Show answer & solution

Answer: (B) 5wL⁴/384EI

It occurs at mid-span.

Question 5

What is the maximum deflection of a beam fixed at both ends carrying a central point load W?

  1. WL³/48EI
  2. WL³/192EI
  3. 5WL³/384EI
  4. WL³/3EI
Show answer & solution

Answer: (B) WL³/192EI

It is one-quarter of the deflection of a simply supported beam.

Question 6

What is flexural rigidity?

  1. The product of modulus of elasticity and moment of inertia (EI)
  2. The bending moment at a section
  3. The section modulus
  4. The ratio of load to deflection
Show answer & solution

Answer: (A) The product of modulus of elasticity and moment of inertia (EI)

A higher EI means less deflection.

Question 7

Which methods are used to find slope and deflection of beams?

  1. Lamé's equations
  2. Mohr's circle only
  3. Euler's formula only
  4. Double integration, Macaulay's method, moment-area method and conjugate beam method
Show answer & solution

Answer: (D) Double integration, Macaulay's method, moment-area method and conjugate beam method

Macaulay's method is convenient for several point loads.

Question 8

What does a fixed (non-yielding) support imply about the slope of a beam?

  1. The slope is maximum
  2. The bending moment is zero
  3. The slope at the support is zero
  4. The deflection is maximum
Show answer & solution

Answer: (C) The slope at the support is zero

A fixed support prevents both rotation and deflection.

Question 9

How does the deflection of a beam change if its span is doubled, with the same central point load?

  1. It increases eight times
  2. It doubles
  3. It increases four times
  4. It stays the same
Show answer & solution

Answer: (A) It increases eight times

Deflection under a point load is proportional to L³.

Question 10

How does the deflection of a rectangular beam change if its depth is doubled?

  1. It stays the same
  2. It becomes one-quarter
  3. It becomes one-eighth
  4. It halves
Show answer & solution

Answer: (C) It becomes one-eighth

Deflection ∝ 1/I and I ∝ d³.

Question 11

What is a column?

  1. A horizontal beam
  2. A tension member
  3. A shaft in torsion
  4. A vertical compression member whose length is large compared with its cross-sectional dimensions
Show answer & solution

Answer: (D) A vertical compression member whose length is large compared with its cross-sectional dimensions

Long columns fail by buckling.

Question 12

What is buckling?

  1. Failure by torsion
  2. Sudden lateral bending and failure of a slender member under compression
  3. Failure by shear only
  4. Failure by crushing only
Show answer & solution

Answer: (B) Sudden lateral bending and failure of a slender member under compression

It occurs below the material's crushing strength in long columns.

Question 13

What is Euler's formula for the crippling (buckling) load of a long column?

  1. P = σA
  2. P = π²EI/Le²
  3. P = π²EA/L
  4. P = EI/L
Show answer & solution

Answer: (B) P = π²EI/Le²

Le is the effective length of the column.

Question 14

What is the effective length of a column with both ends hinged?

  1. 2L
  2. L/√2
  3. L
  4. L/2
Show answer & solution

Answer: (C) L

It is the standard case for Euler's formula.

Question 15

What is the effective length of a column with one end fixed and the other end free?

  1. L
  2. L/2
  3. L/√2
  4. 2L
Show answer & solution

Answer: (D) 2L

This case has the lowest buckling load.

Question 16

What is the effective length of a column with both ends fixed?

  1. L/2
  2. 2L
  3. L
  4. L/√2
Show answer & solution

Answer: (A) L/2

Its buckling load is four times that of a column with hinged ends.

Question 17

What is the effective length of a column with one end fixed and the other hinged?

  1. L
  2. L/√2
  3. 2L
  4. L/2
Show answer & solution

Answer: (B) L/√2

Its buckling load is twice that of a column with hinged ends.

Question 18

How does the buckling load of a column with both ends fixed compare with one with both ends hinged?

  1. It is twice as large
  2. It is equal
  3. It is half
  4. It is four times as large
Show answer & solution

Answer: (D) It is four times as large

Effective length is halved, and P ∝ 1/Le².

Question 19

What is the slenderness ratio of a column?

  1. The ratio of area to length
  2. The ratio of length to diameter
  3. The ratio of effective length to least radius of gyration
  4. The ratio of load to area
Show answer & solution

Answer: (C) The ratio of effective length to least radius of gyration

Columns with high slenderness ratios fail by buckling.

Question 20

On which factors does the buckling load of a column depend?

  1. Slenderness ratio, cross-sectional area and modulus of elasticity
  2. Density only
  3. Yield stress only
  4. Poisson's ratio only
Show answer & solution

Answer: (A) Slenderness ratio, cross-sectional area and modulus of elasticity

These factors combine in Euler's formula.

Question 21

For which type of columns is Euler's formula valid?

  1. Long, slender columns
  2. Only tension members
  3. Short, stubby columns
  4. All columns equally
Show answer & solution

Answer: (A) Long, slender columns

Short columns fail by crushing rather than buckling.

Question 22

Which formula is used for columns of intermediate length, combining crushing and buckling?

  1. Euler's formula only
  2. Lamé's formula
  3. Macaulay's formula
  4. Rankine–Gordon formula
Show answer & solution

Answer: (D) Rankine–Gordon formula

It gives realistic loads for both short and long columns.

Question 23

What does the middle-third rule state for a rectangular section under eccentric compression?

  1. Load must always act at the edge
  2. Tension occurs only in the middle third
  3. There is no tension if the load acts within the middle third of the section
  4. There is no compression in the middle third
Show answer & solution

Answer: (C) There is no tension if the load acts within the middle third of the section

The core (kern) extends b/6 on each side of the centroid.

Question 24

For a solid circular section, within what zone must a compressive load act to avoid tension anywhere?

  1. Anywhere
  2. Within a central circle of diameter d/4 (the middle quarter)
  3. Within the middle third
  4. At the edge only
Show answer & solution

Answer: (B) Within a central circle of diameter d/4 (the middle quarter)

This zone is the core or kern of the section.

Question 25

What is the slope at the free end of a cantilever of length L carrying a point load W at the free end?

  1. WL²/2EI
  2. WL³/3EI
  3. WL/2EI
  4. WL²/EI
Show answer & solution

Answer: (A) WL²/2EI

Slope and deflection are both maximum at the free end.

Question 26

What is the slope at each support of a simply supported beam carrying a central point load W?

  1. WL²/48EI
  2. WL²/16EI
  3. WL²/2EI
  4. WL³/48EI
Show answer & solution

Answer: (B) WL²/16EI

The slope at mid-span is zero.

Question 27

What is the maximum deflection of a beam fixed at both ends carrying a uniformly distributed load w over span L?

  1. wL⁴/48EI
  2. 5wL⁴/384EI
  3. wL⁴/8EI
  4. wL⁴/384EI
Show answer & solution

Answer: (D) wL⁴/384EI

It is one-fifth of the deflection of a simply supported beam.

Question 28

What is the moment-area theorem used for?

  1. Finding principal stresses
  2. Finding buckling loads
  3. Finding slope and deflection of beams from the area of the M/EI diagram
  4. Finding torque in shafts
Show answer & solution

Answer: (C) Finding slope and deflection of beams from the area of the M/EI diagram

It was developed by Mohr and Greene.

Question 29

What does the conjugate beam method use?

  1. Mohr's circle
  2. An imaginary beam loaded with the M/EI diagram of the real beam
  3. The shear force diagram only
  4. The actual loads only
Show answer & solution

Answer: (B) An imaginary beam loaded with the M/EI diagram of the real beam

The shear and bending moment in the conjugate beam give slope and deflection of the real beam.

Question 30

What is a statically indeterminate beam?

  1. A beam whose reactions cannot be found from the equations of static equilibrium alone
  2. A beam with no supports
  3. A cantilever
  4. A simply supported beam
Show answer & solution

Answer: (A) A beam whose reactions cannot be found from the equations of static equilibrium alone

Fixed and continuous beams are statically indeterminate.

Question 31

What is the fixed-end moment at each end of a beam fixed at both ends carrying a central point load W over span L?

  1. WL/2
  2. WL/4
  3. WL/12
  4. WL/8
Show answer & solution

Answer: (D) WL/8

The mid-span moment is also WL/8, of opposite sign.

Question 32

What is the fixed-end moment at each end of a beam fixed at both ends carrying a uniformly distributed load w over span L?

  1. wL²/2
  2. wL²/8
  3. wL²/12
  4. wL²/24
Show answer & solution

Answer: (C) wL²/12

The mid-span moment is wL²/24.

Question 33

What is the least radius of gyration of a section?

  1. I/A
  2. A/I
  3. √(A/I)
  4. √(I_min/A)
Show answer & solution

Answer: (D) √(I_min/A)

Columns buckle about the axis with the least radius of gyration.

Question 34

Why are hollow circular sections efficient for columns?

  1. They have a large radius of gyration for a given area, reducing slenderness ratio
  2. They are cheaper to weld
  3. They have smaller moment of inertia
  4. They are heavier
Show answer & solution

Answer: (A) They have a large radius of gyration for a given area, reducing slenderness ratio

Tubular steel columns are common in structures.

Question 35

What is the crippling load of a column?

  1. The load at which it crushes
  2. The impact load
  3. The load at which the column just begins to buckle
  4. The working load
Show answer & solution

Answer: (C) The load at which the column just begins to buckle

It is also called the critical or buckling load.

Question 36

What happens to the Euler buckling load if the length of a column is doubled?

  1. It halves
  2. It becomes one-quarter
  3. It stays the same
  4. It doubles
Show answer & solution

Answer: (B) It becomes one-quarter

P ∝ 1/L².

Practice these 36 questions interactively →