Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Internal Combustion Engines: Engine Systems

Mechanical Engineering · Internal Combustion Engines

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the function of a spark plug?

  1. To measure temperature
  2. To control speed
  3. To produce an electric spark that ignites the air–fuel mixture in an SI engine
  4. To inject fuel
Show answer & solution

Answer: (C) To produce an electric spark that ignites the air–fuel mixture in an SI engine

It is screwed into the cylinder head.

Question 2

What is the function of the ignition coil in a battery ignition system?

  1. To store fuel
  2. To step up the battery voltage (12 V) to the high voltage needed for the spark (about 20,000–30,000 V)
  3. To start the engine
  4. To charge the battery
Show answer & solution

Answer: (B) To step up the battery voltage (12 V) to the high voltage needed for the spark (about 20,000–30,000 V)

It works like a transformer.

Question 3

What is the function of the distributor in a conventional ignition system?

  1. To deliver the high-voltage spark to each spark plug in the correct firing order and time
  2. To pump fuel
  3. To cool the engine
  4. To charge the battery
Show answer & solution

Answer: (A) To deliver the high-voltage spark to each spark plug in the correct firing order and time

Ignition timing is adjusted by rotating the distributor.

Question 4

What is the function of the condenser (capacitor) in a contact-breaker ignition system?

  1. To cool the coil
  2. To store fuel
  3. To raise the battery voltage
  4. To reduce arcing at the contact breaker points and speed up the collapse of the magnetic field
Show answer & solution

Answer: (D) To reduce arcing at the contact breaker points and speed up the collapse of the magnetic field

It prolongs contact point life.

Question 5

What is a magneto?

  1. A battery
  2. A fuel pump
  3. A self-contained alternating current generator that produces ignition current without a battery
  4. A DC motor
Show answer & solution

Answer: (C) A self-contained alternating current generator that produces ignition current without a battery

It is used in motorcycles, small engines and aircraft.

Question 6

Why do diesel engines not need an ignition system?

  1. Fuel ignites by the heat of compression
  2. They use spark plugs
  3. They use magnetos
  4. They use glow plugs throughout operation
Show answer & solution

Answer: (A) Fuel ignites by the heat of compression

Glow plugs are used only for cold starting in some engines.

Question 7

What is the firing order of an engine?

  1. The order of fuel tanks
  2. The order of valve opening only
  3. The sequence in which the cylinders fire
  4. The order in which cylinders are assembled
Show answer & solution

Answer: (C) The sequence in which the cylinders fire

It is chosen to balance the engine and reduce vibration.

Question 8

What is the most common firing order for a four-cylinder in-line engine?

  1. 1-2-3-4
  2. 1-3-4-2
  3. 1-4-2-3
  4. 4-3-2-1
Show answer & solution

Answer: (B) 1-3-4-2

1-2-4-3 is also used.

Question 9

What is a common firing order for a six-cylinder in-line engine?

  1. 1-2-3-4-5-6
  2. 1-5-3-6-2-4
  3. 1-6-2-5-3-4
  4. 6-5-4-3-2-1
Show answer & solution

Answer: (B) 1-5-3-6-2-4

It balances the crankshaft loads.

Question 10

Why is cooling necessary in IC engines?

  1. To increase power without limit
  2. To heat the fuel
  3. To reduce fuel consumption only
  4. To prevent overheating, which would damage lubricating oil, pistons, valves and cylinder walls
Show answer & solution

Answer: (D) To prevent overheating, which would damage lubricating oil, pistons, valves and cylinder walls

About a third of the fuel heat goes to the coolant.

Question 11

What is the function of the thermostat in an engine cooling system?

  1. To cool oil
  2. To increase pressure
  3. To keep coolant temperature at the correct level by controlling flow to the radiator
  4. To pump water
Show answer & solution

Answer: (C) To keep coolant temperature at the correct level by controlling flow to the radiator

It stays closed until the engine warms up.

Question 12

Why is a pressure cap fitted on a radiator?

  1. To raise the boiling point of the coolant by pressurising the system
  2. To reduce pressure
  3. To cool the engine faster by boiling
  4. To add water automatically
Show answer & solution

Answer: (A) To raise the boiling point of the coolant by pressurising the system

A typical cap holds about 1 bar above atmospheric.

Question 13

Why is ethylene glycol added to engine coolant?

  1. To increase its viscosity
  2. To clean the radiator only
  3. To lubricate the pistons
  4. To lower its freezing point and raise its boiling point
Show answer & solution

Answer: (D) To lower its freezing point and raise its boiling point

It is the main ingredient of antifreeze.

Question 14

Which type of cooling is common in motorcycle engines?

  1. Water cooling with radiator only
  2. Oil cooling only
  3. Air cooling using fins on the cylinder
  4. No cooling
Show answer & solution

Answer: (C) Air cooling using fins on the cylinder

Fins increase the surface area for heat transfer.

Question 15

What is the purpose of lubrication in an IC engine?

  1. Heating the engine
  2. Increasing friction
  3. Increasing fuel consumption
  4. Reducing friction and wear, cooling parts, sealing the piston rings and cleaning the engine
Show answer & solution

Answer: (D) Reducing friction and wear, cooling parts, sealing the piston rings and cleaning the engine

Engine oil also protects against corrosion.

Question 16

Which lubrication system is used in most modern automobile engines?

  1. Splash lubrication only
  2. Pressure (forced) feed system with an oil pump
  3. Petroil lubrication
  4. Grease lubrication
Show answer & solution

Answer: (B) Pressure (forced) feed system with an oil pump

Oil is pumped through drillings to bearings.

Question 17

What is the difference between wet sump and dry sump lubrication?

  1. In a wet sump, oil is stored in the crankcase sump; in a dry sump, oil is stored in a separate tank
  2. They are the same
  3. A wet sump uses grease
  4. A dry sump has no oil
Show answer & solution

Answer: (A) In a wet sump, oil is stored in the crankcase sump; in a dry sump, oil is stored in a separate tank

Dry sump systems are used in racing and aircraft engines.

Question 18

What does "W" stand for in a multigrade oil such as 10W-40?

  1. Wear
  2. Weight
  3. Winter, indicating its low-temperature viscosity grade
  4. Water
Show answer & solution

Answer: (C) Winter, indicating its low-temperature viscosity grade

Multigrade oils behave like thin oil when cold and thick oil when hot.

Question 19

Why are engine pistons usually made of aluminium alloy?

  1. It does not expand
  2. It is cheaper than all other metals
  3. It is heavier than cast iron
  4. It is light and conducts heat well
Show answer & solution

Answer: (D) It is light and conducts heat well

Lighter pistons reduce inertia forces.

Question 20

What are piston rings usually made of?

  1. Fine-grained cast iron
  2. Plastic
  3. Aluminium
  4. Copper
Show answer & solution

Answer: (A) Fine-grained cast iron

Cast iron has good wear and spring properties.

Question 21

What is the function of compression rings?

  1. To scrape oil from the cylinder
  2. To seal the gap between piston and cylinder and prevent leakage of gases
  3. To cool the piston only
  4. To hold the gudgeon pin
Show answer & solution

Answer: (B) To seal the gap between piston and cylinder and prevent leakage of gases

They are fitted at the top of the piston.

Question 22

What is the function of the oil control (scraper) ring?

  1. To cool the cylinder only
  2. To hold the piston
  3. To scrape excess oil from the cylinder wall and return it to the sump
  4. To seal compression gases
Show answer & solution

Answer: (C) To scrape excess oil from the cylinder wall and return it to the sump

It is fitted below the compression rings.

Question 23

Why are piston rings sometimes plated with chromium?

  1. To reduce wear and prevent scuffing
  2. For colour
  3. To make them heavier
  4. To increase friction
Show answer & solution

Answer: (A) To reduce wear and prevent scuffing

Chrome-plated top rings last longer.

Question 24

What is the gudgeon (piston) pin?

  1. The pin holding the crankshaft
  2. A valve spring pin
  3. The pin on the camshaft
  4. The pin connecting the piston to the small end of the connecting rod
Show answer & solution

Answer: (D) The pin connecting the piston to the small end of the connecting rod

It allows the connecting rod to swing.

Question 25

What is a cylinder liner?

  1. A gasket
  2. A replaceable sleeve fitted into the cylinder block to form the cylinder wall
  3. A piston ring
  4. A valve seat
Show answer & solution

Answer: (B) A replaceable sleeve fitted into the cylinder block to form the cylinder wall

Wet liners are in direct contact with coolant; dry liners are not.

Question 26

What are the main pollutants in IC engine exhaust?

  1. Carbon monoxide, unburned hydrocarbons, oxides of nitrogen and particulate matter
  2. Water vapour only
  3. Helium
  4. Oxygen and nitrogen only
Show answer & solution

Answer: (A) Carbon monoxide, unburned hydrocarbons, oxides of nitrogen and particulate matter

Diesel engines produce more NOx and particulates.

Question 27

What does a three-way catalytic converter do?

  1. Removes only smoke
  2. Cools the exhaust only
  3. Converts CO, unburned hydrocarbons and NOx into CO₂, water and nitrogen
  4. Increases engine power
Show answer & solution

Answer: (C) Converts CO, unburned hydrocarbons and NOx into CO₂, water and nitrogen

It works best with a stoichiometric mixture controlled by an oxygen sensor.

Question 28

What is exhaust gas recirculation (EGR) used for?

  1. Cooling the oil
  2. Reducing NOx emissions by lowering peak combustion temperature
  3. Reducing CO only
  4. Increasing power
Show answer & solution

Answer: (B) Reducing NOx emissions by lowering peak combustion temperature

Part of the exhaust is fed back to the intake.

Question 29

What is a diesel particulate filter (DPF)?

  1. An oil filter
  2. An air filter
  3. A fuel filter
  4. A filter in the exhaust that traps soot particles from diesel engines
Show answer & solution

Answer: (D) A filter in the exhaust that traps soot particles from diesel engines

It is periodically cleaned by burning off the soot.

Question 30

What is the function of an air filter?

  1. To enrich the mixture
  2. To remove dust from intake air to prevent engine wear
  3. To cool the air
  4. To increase air pressure
Show answer & solution

Answer: (B) To remove dust from intake air to prevent engine wear

A clogged filter causes a richer mixture and loss of power.

Question 31

What is the purpose of the vacuum advance unit in a distributor?

  1. To advance the spark at part load when the mixture burns more slowly
  2. To charge the battery
  3. To cool the coil
  4. To retard the spark at full load
Show answer & solution

Answer: (A) To advance the spark at part load when the mixture burns more slowly

It responds to intake manifold vacuum.

Question 32

What replaced contact breaker points in modern ignition systems?

  1. Glow plugs
  2. Carburettors
  3. Magnetos only
  4. Electronic ignition with transistor switching and sensors
Show answer & solution

Answer: (D) Electronic ignition with transistor switching and sensors

Electronic systems need less maintenance.

Question 33

What is the function of the water pump in an engine cooling system?

  1. To fill the radiator
  2. To control temperature directly
  3. To cool oil
  4. To circulate coolant through the engine and radiator
Show answer & solution

Answer: (D) To circulate coolant through the engine and radiator

It is usually driven by a belt from the crankshaft.

Question 34

What is the function of the oil filter?

  1. To mix oil with fuel
  2. To remove dirt and metal particles from the lubricating oil
  3. To pump oil
  4. To cool the oil
Show answer & solution

Answer: (B) To remove dirt and metal particles from the lubricating oil

Clogged filters are bypassed by a relief valve.

Question 35

What is the function of the crankshaft?

  1. To convert the reciprocating motion of the pistons into rotary motion
  2. To cool the engine
  3. To open the valves
  4. To pump fuel
Show answer & solution

Answer: (A) To convert the reciprocating motion of the pistons into rotary motion

Crankshafts are usually forged steel.

Question 36

What opens and closes the valves in a four-stroke engine?

  1. The spark plug
  2. The piston
  3. Cams on the camshaft, through tappets, push rods or rocker arms
  4. The crankshaft directly
Show answer & solution

Answer: (C) Cams on the camshaft, through tappets, push rods or rocker arms

Valve springs close the valves.

Question 37

What is the function of the cylinder head gasket?

  1. To store fuel
  2. To seal the joint between the cylinder head and block against gas, coolant and oil leakage
  3. To lubricate the pistons
  4. To cool the engine
Show answer & solution

Answer: (B) To seal the joint between the cylinder head and block against gas, coolant and oil leakage

A blown gasket causes loss of compression.

Question 38

What is blow-by?

  1. Air leakage into the intake
  2. Oil leakage from the sump
  3. Leakage of combustion gases past the piston rings into the crankcase
  4. Fuel leakage from the tank
Show answer & solution

Answer: (C) Leakage of combustion gases past the piston rings into the crankcase

Positive crankcase ventilation returns blow-by gases to the intake.

Practice these 38 questions interactively →