Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Internal Combustion Engines: Engine Fundamentals

Mechanical Engineering · Internal Combustion Engines

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is an internal combustion engine?

  1. A steam engine
  2. An electric motor
  3. An engine in which fuel burns outside the cylinder
  4. A heat engine in which fuel is burned inside the engine cylinder and the products of combustion act directly as the working fluid
Show answer & solution

Answer: (D) A heat engine in which fuel is burned inside the engine cylinder and the products of combustion act directly as the working fluid

Petrol and diesel engines are internal combustion engines.

Question 2

Which of the following is not an internal combustion engine?

  1. Gas turbine
  2. Steam turbine
  3. Diesel engine
  4. Petrol engine
Show answer & solution

Answer: (B) Steam turbine

Steam turbines are external combustion machines.

Question 3

What is the main difference between spark ignition (SI) and compression ignition (CI) engines?

  1. SI engines use diesel fuel
  2. CI engines need spark plugs
  3. SI engines ignite the mixture with a spark, while CI engines ignite fuel by the heat of compressed air
  4. They have the same ignition method
Show answer & solution

Answer: (C) SI engines ignite the mixture with a spark, while CI engines ignite fuel by the heat of compressed air

Petrol engines are SI and diesel engines are CI.

Question 4

What does a four-stroke engine require to complete one working cycle?

  1. Four piston strokes, or two crankshaft revolutions
  2. One stroke
  3. Two strokes, or one revolution
  4. Four revolutions
Show answer & solution

Answer: (A) Four piston strokes, or two crankshaft revolutions

The strokes are suction, compression, power and exhaust.

Question 5

How many crankshaft revolutions does a two-stroke engine need to complete one working cycle?

  1. Two
  2. Half
  3. One
  4. Four
Show answer & solution

Answer: (C) One

There is a power stroke every revolution.

Question 6

At what speed does the camshaft of a four-stroke engine run compared with the crankshaft?

  1. Twice the crankshaft speed
  2. Half the crankshaft speed
  3. Same as crankshaft speed
  4. Four times crankshaft speed
Show answer & solution

Answer: (B) Half the crankshaft speed

A crankshaft at 1500 rpm drives the camshaft at 750 rpm.

Question 7

How can a two-stroke engine usually be identified?

  1. It has ports in the cylinder instead of poppet valves
  2. It has no crankcase
  3. It has a camshaft
  4. It has four valves per cylinder
Show answer & solution

Answer: (A) It has ports in the cylinder instead of poppet valves

The piston uncovers ports as it moves.

Question 8

Which ports are found in a crankcase-scavenged two-stroke petrol engine?

  1. Only inlet and exhaust valves
  2. Only a transfer port
  3. Only an exhaust port
  4. Inlet (suction) port, exhaust port and transfer port
Show answer & solution

Answer: (D) Inlet (suction) port, exhaust port and transfer port

Fresh charge is compressed in the crankcase and transferred to the cylinder.

Question 9

How does the power of a two-stroke engine compare with a four-stroke engine of the same size and speed?

  1. Exactly half
  2. About 1.7 to 1.8 times greater, not double, due to scavenging losses
  3. Four times greater
  4. Exactly the same
Show answer & solution

Answer: (B) About 1.7 to 1.8 times greater, not double, due to scavenging losses

It has twice as many power strokes but loses some fresh charge.

Question 10

How does the thermal efficiency of a two-stroke engine compare with a four-stroke engine?

  1. It is lower
  2. It is double
  3. It is higher
  4. It is the same
Show answer & solution

Answer: (A) It is lower

Some fresh charge escapes with exhaust gases.

Question 11

How are small two-stroke motorcycle and scooter engines commonly lubricated?

  1. By splash only
  2. By a full pressure-feed system
  3. By mixing a small percentage of lubricating oil with petrol
  4. They need no lubrication
Show answer & solution

Answer: (C) By mixing a small percentage of lubricating oil with petrol

This is called petroil lubrication.

Question 12

What is scavenging in an engine?

  1. Cooling the cylinder
  2. Igniting the fuel
  3. Compressing the charge
  4. Clearing burnt exhaust gases from the cylinder and replacing them with fresh air or charge
Show answer & solution

Answer: (D) Clearing burnt exhaust gases from the cylinder and replacing them with fresh air or charge

It is essential in two-stroke engines.

Question 13

Which type of scavenging is generally the most efficient in two-stroke engines?

  1. Cross scavenging
  2. Uniflow scavenging
  3. No scavenging
  4. Loop scavenging
Show answer & solution

Answer: (B) Uniflow scavenging

Flow moves in one direction from inlet ports to exhaust valves.

Question 14

What is crankcase scavenging?

  1. Using a separate blower
  2. Using a turbocharger
  3. Using exhaust gases
  4. Using the underside of the piston to compress fresh charge in the crankcase before it enters the cylinder
Show answer & solution

Answer: (D) Using the underside of the piston to compress fresh charge in the crankcase before it enters the cylinder

The piston's motion provides the pressure.

Question 15

What is the swept (stroke) volume of an engine cylinder?

  1. The clearance volume
  2. The total volume of all cylinders only
  3. The volume displaced by the piston as it moves from top dead centre to bottom dead centre
  4. The crankcase volume
Show answer & solution

Answer: (C) The volume displaced by the piston as it moves from top dead centre to bottom dead centre

A "125 cc" engine has 125 cm³ of swept volume.

Question 16

What is the usual range of compression ratio for petrol (SI) engines?

  1. About 1 to 3
  2. About 6 to 12
  3. About 14 to 22
  4. About 25 to 40
Show answer & solution

Answer: (B) About 6 to 12

Knocking limits the compression ratio of petrol engines.

Question 17

What is the usual range of compression ratio for diesel (CI) engines?

  1. About 2 to 4
  2. About 6 to 10
  3. About 14 to 22
  4. About 30 to 50
Show answer & solution

Answer: (C) About 14 to 22

High compression is needed to raise air temperature for self-ignition.

Question 18

What is a square engine?

  1. An engine with four cylinders
  2. An engine with a square piston
  3. An engine with square valves
  4. An engine whose bore equals its stroke
Show answer & solution

Answer: (D) An engine whose bore equals its stroke

Over-square engines have bore greater than stroke.

Question 19

On which air-standard cycle does a petrol engine work?

  1. Otto cycle (constant volume heat addition)
  2. Diesel cycle
  3. Rankine cycle
  4. Brayton cycle
Show answer & solution

Answer: (A) Otto cycle (constant volume heat addition)

It is named after Nikolaus Otto.

Question 20

On which air-standard cycle do slow-speed diesel engines work?

  1. Stirling cycle
  2. Otto cycle
  3. Brayton cycle
  4. Diesel cycle (constant pressure heat addition)
Show answer & solution

Answer: (D) Diesel cycle (constant pressure heat addition)

It is named after Rudolf Diesel.

Question 21

On which cycle do most modern high-speed diesel engines operate?

  1. Rankine cycle
  2. Pure Otto cycle
  3. Dual combustion cycle
  4. Pure Diesel cycle
Show answer & solution

Answer: (C) Dual combustion cycle

Heat is added partly at constant volume and partly at constant pressure.

Question 22

What happens to the efficiency of the Diesel cycle as the cut-off ratio increases, at fixed compression ratio?

  1. It increases
  2. It decreases
  3. It stays the same
  4. It becomes 100%
Show answer & solution

Answer: (B) It decreases

Heat is added over a longer part of the stroke.

Question 23

What is valve timing?

  1. The spark timing only
  2. The speed of the camshaft
  3. The crank angles at which the inlet and exhaust valves open and close
  4. The size of the valves
Show answer & solution

Answer: (C) The crank angles at which the inlet and exhaust valves open and close

It is shown on a valve timing diagram.

Question 24

Why does the inlet valve of a four-stroke engine close some degrees after bottom dead centre?

  1. The momentum of incoming charge continues to fill the cylinder, improving volumetric efficiency
  2. To allow exhaust to escape
  3. To reduce power
  4. To cool the valve
Show answer & solution

Answer: (A) The momentum of incoming charge continues to fill the cylinder, improving volumetric efficiency

It typically closes about 30–40° after BDC.

Question 25

Why does the exhaust valve open before bottom dead centre?

  1. To admit fresh charge
  2. To let exhaust gases escape early and reduce the work needed to expel them
  3. To increase compression
  4. To cool the cylinder
Show answer & solution

Answer: (B) To let exhaust gases escape early and reduce the work needed to expel them

It typically opens about 40–50° before BDC.

Question 26

What is valve overlap?

  1. The time of fuel injection
  2. The period when both valves are closed
  3. The time when the spark occurs
  4. The period when both inlet and exhaust valves are open together near top dead centre
Show answer & solution

Answer: (D) The period when both inlet and exhaust valves are open together near top dead centre

It helps scavenge the clearance space.

Question 27

Why is the inlet valve usually larger than the exhaust valve?

  1. Exhaust gases need more area
  2. To reduce cost
  3. The incoming charge is at low pressure and needs a larger flow area to fill the cylinder
  4. To increase compression
Show answer & solution

Answer: (C) The incoming charge is at low pressure and needs a larger flow area to fill the cylinder

Exhaust gases leave under higher pressure.

Question 28

What is a Wankel engine?

  1. A rotary internal combustion engine using a triangular rotor instead of reciprocating pistons
  2. A two-stroke diesel engine
  3. A steam engine
  4. A gas turbine
Show answer & solution

Answer: (A) A rotary internal combustion engine using a triangular rotor instead of reciprocating pistons

It is compact and smooth but has sealing problems.

Question 29

Where is the combustion chamber of an opposed-piston diesel engine located?

  1. In the crankcase
  2. Above a single piston
  3. Outside the cylinder
  4. Between the two pistons in a common cylinder
Show answer & solution

Answer: (D) Between the two pistons in a common cylinder

Such engines have no cylinder head.

Question 30

What is the function of a flywheel in an IC engine?

  1. To start the engine
  2. To smooth out power impulses and keep speed nearly constant during each cycle
  3. To control mean speed
  4. To cool the engine
Show answer & solution

Answer: (B) To smooth out power impulses and keep speed nearly constant during each cycle

It stores energy during the power stroke and releases it during other strokes.

Question 31

Which engine needs a bigger flywheel for the same power and speed?

  1. A multi-cylinder engine
  2. An electric motor
  3. A four-stroke engine compared with a two-stroke engine
  4. A two-stroke engine
Show answer & solution

Answer: (C) A four-stroke engine compared with a two-stroke engine

A four-stroke engine has fewer power strokes per revolution.

Question 32

Why do diesel engines generally need a bigger flywheel than petrol engines?

  1. They have higher peak pressures and greater fluctuations in torque
  2. They are lighter
  3. They run faster
  4. They have spark ignition
Show answer & solution

Answer: (A) They have higher peak pressures and greater fluctuations in torque

Diesel engines are also heavier in construction.

Question 33

What is the clearance volume of an engine?

  1. The crankcase volume
  2. The volume above the piston when it is at top dead centre
  3. The swept volume
  4. The total engine displacement
Show answer & solution

Answer: (B) The volume above the piston when it is at top dead centre

It forms the combustion space.

Question 34

What is the effect of carbon deposits on the compression ratio?

  1. They have no effect
  2. They increase the effective compression ratio
  3. They make it zero
  4. They reduce it
Show answer & solution

Answer: (B) They increase the effective compression ratio

Deposits take up clearance space.

Question 35

What are the main advantages of multi-cylinder engines over single-cylinder engines of the same power?

  1. More vibration
  2. Higher cost only
  3. Simpler construction
  4. Smoother torque, better balance and a smaller flywheel
Show answer & solution

Answer: (D) Smoother torque, better balance and a smaller flywheel

However, they have more parts.

Question 36

What is the effect of increasing the number of cylinders on the power-to-weight ratio of an engine?

  1. It always decreases it
  2. It makes it zero
  3. It generally increases the power-to-weight ratio
  4. It has no effect
Show answer & solution

Answer: (C) It generally increases the power-to-weight ratio

Smaller cylinders can run faster and need lighter flywheels.

Question 37

Which engine arrangement is chosen when overhead clearance is limited?

  1. Horizontal (flat or opposed) engine
  2. Radial engine
  3. V-engine with high cylinders
  4. Vertical in-line engine
Show answer & solution

Answer: (A) Horizontal (flat or opposed) engine

Flat engines have a low height.

Question 38

What are the advantages of a V-engine?

  1. It needs more length
  2. It is shorter and more compact than an in-line engine with the same number of cylinders
  3. It is always cheaper
  4. It has only one cylinder
Show answer & solution

Answer: (B) It is shorter and more compact than an in-line engine with the same number of cylinders

V6 and V8 engines are common.

Question 39

What is a radial engine?

  1. An in-line engine
  2. A two-stroke engine only
  3. An engine with cylinders arranged around the crankshaft like the spokes of a wheel
  4. A rotary Wankel engine
Show answer & solution

Answer: (C) An engine with cylinders arranged around the crankshaft like the spokes of a wheel

It was widely used in older aircraft.

Practice these 39 questions interactively →