Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Internal Combustion Engines: SI Engine Combustion

Mechanical Engineering · Internal Combustion Engines

41 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the boiling (distillation) range of petrol?

  1. About 0–20 °C
  2. About 30–200 °C
  3. About 220–350 °C
  4. About 350–500 °C
Show answer & solution

Answer: (B) About 30–200 °C

Kerosene distils at about 150–300 °C and diesel at about 200–350 °C.

Question 2

What is the approximate specific gravity of diesel oil?

  1. 0.65
  2. 0.85
  3. 1.0
  4. 1.3
Show answer & solution

Answer: (B) 0.85

Petrol has a specific gravity of about 0.72–0.75.

Question 3

What is the approximate calorific value of petrol?

  1. About 4 MJ/kg
  2. About 10 MJ/kg
  3. About 44 MJ/kg (lower heating value)
  4. About 100 MJ/kg
Show answer & solution

Answer: (C) About 44 MJ/kg (lower heating value)

Diesel has a similar value of about 43 MJ/kg.

Question 4

What is the difference between higher and lower calorific values of a fuel?

  1. The lower value includes latent heat
  2. The higher value excludes combustion heat
  3. They are the same
  4. The higher value includes the latent heat of the water vapour formed, which the lower value excludes
Show answer & solution

Answer: (D) The higher value includes the latent heat of the water vapour formed, which the lower value excludes

Engines cannot use the latent heat because water leaves as vapour.

Question 5

Which calorific value is generally used to assess engine fuel consumption guarantees?

  1. Lower calorific value
  2. Zero calorific value
  3. Higher calorific value
  4. Average calorific value
Show answer & solution

Answer: (A) Lower calorific value

Water leaves the engine as vapour.

Question 6

In what units is the calorific value of gaseous fuels usually expressed?

  1. kJ/m²
  2. kJ/litre of water
  3. kJ/kg only
  4. kJ/m³ (or kcal/m³)
Show answer & solution

Answer: (D) kJ/m³ (or kcal/m³)

Gas volumes are measured at standard conditions.

Question 7

What is the flash point of a fuel?

  1. The temperature at which it burns continuously
  2. The temperature at which it freezes
  3. The lowest temperature at which it gives off vapour that ignites momentarily when a flame is brought near
  4. The temperature at which it boils
Show answer & solution

Answer: (C) The lowest temperature at which it gives off vapour that ignites momentarily when a flame is brought near

The fire point is slightly higher.

Question 8

What is the pour point of a fuel or oil?

  1. The lowest temperature at which it can still flow
  2. The temperature at which it ignites
  3. The flash point
  4. The temperature at which it boils
Show answer & solution

Answer: (A) The lowest temperature at which it can still flow

The pour point of diesel must be lower than the coldest temperature it will meet.

Question 9

What is the chemically correct (stoichiometric) air–fuel ratio for petrol?

  1. About 5:1
  2. About 15:1 by mass (14.7:1)
  3. About 30:1
  4. About 100:1
Show answer & solution

Answer: (B) About 15:1 by mass (14.7:1)

At this ratio all fuel and oxygen are used up.

Question 10

What air–fuel ratio gives maximum power in a petrol engine?

  1. A very lean mixture of 25:1
  2. Stoichiometric only
  3. A lean mixture of 18:1
  4. A slightly rich mixture of about 12–13:1
Show answer & solution

Answer: (D) A slightly rich mixture of about 12–13:1

Rich mixtures make full use of the air.

Question 11

What air–fuel ratio gives the best fuel economy in a petrol engine?

  1. A very rich mixture of 8:1
  2. A slightly lean mixture of about 16–17:1
  3. Pure air
  4. A rich mixture of 10:1
Show answer & solution

Answer: (B) A slightly lean mixture of about 16–17:1

Excess air ensures complete combustion of fuel.

Question 12

What mixture does a petrol engine need for idling and cold starting?

  1. A lean mixture
  2. Stoichiometric mixture only
  3. A rich mixture
  4. No fuel
Show answer & solution

Answer: (C) A rich mixture

Idling mixtures may be about 10–12:1.

Question 13

What is the purpose of carburetion?

  1. To break up petrol into fine droplets and mix it with air in the right proportion
  2. To compress the air
  3. To cool the engine
  4. To ignite the fuel
Show answer & solution

Answer: (A) To break up petrol into fine droplets and mix it with air in the right proportion

Modern cars use fuel injection instead.

Question 14

How does a simple carburettor deliver fuel?

  1. Fuel is injected into the cylinder
  2. Fuel flows by gravity into the cylinder
  3. Fuel is pumped at high pressure
  4. Air flowing through a venturi creates low pressure that draws fuel from a jet fed by a float chamber
Show answer & solution

Answer: (D) Air flowing through a venturi creates low pressure that draws fuel from a jet fed by a float chamber

The float keeps the fuel level just below the jet tip.

Question 15

What is the function of the choke in a carburettor?

  1. To stop the engine
  2. To give a rich mixture for cold starting by restricting air flow
  3. To control engine speed
  4. To lean the mixture at high speed
Show answer & solution

Answer: (B) To give a rich mixture for cold starting by restricting air flow

It is opened once the engine warms up.

Question 16

What does the throttle valve in a petrol engine control?

  1. The air–fuel ratio
  2. The oil pressure
  3. The quantity of air–fuel mixture entering the engine
  4. The spark timing
Show answer & solution

Answer: (C) The quantity of air–fuel mixture entering the engine

This is called quantity governing.

Question 17

What is the problem with a simple carburettor as engine speed increases?

  1. The mixture becomes richer
  2. The float stops working
  3. The mixture stays constant
  4. The mixture becomes leaner
Show answer & solution

Answer: (A) The mixture becomes richer

Compensating jets correct this.

Question 18

What is multi-point fuel injection (MPFI)?

  1. A mechanical fuel pump
  2. Diesel direct injection
  3. A carburettor with many jets
  4. A system in which separate injectors spray petrol into the intake port of each cylinder, controlled electronically
Show answer & solution

Answer: (D) A system in which separate injectors spray petrol into the intake port of each cylinder, controlled electronically

It gives better economy and lower emissions than carburettors.

Question 19

What does the octane number of petrol indicate?

  1. Its volatility only
  2. Its calorific value
  3. Its ease of self-ignition in diesel engines
  4. Its resistance to knocking in SI engines
Show answer & solution

Answer: (D) Its resistance to knocking in SI engines

Higher octane fuel allows higher compression ratios.

Question 20

Which reference fuels are used to determine octane number?

  1. Methane and ethane
  2. Cetane and α-methylnaphthalene
  3. Iso-octane (rated 100) and normal heptane (rated 0)
  4. Benzene and toluene
Show answer & solution

Answer: (C) Iso-octane (rated 100) and normal heptane (rated 0)

The percentage of iso-octane in a matching blend is the octane number.

Question 21

How does normal heptane behave in a petrol engine?

  1. It knocks very easily and is given an octane number of zero
  2. It is rated at 100
  3. It strongly resists knocking
  4. It does not burn
Show answer & solution

Answer: (A) It knocks very easily and is given an octane number of zero

Iso-octane resists knock and is rated 100.

Question 22

What is knocking (detonation) in a petrol engine?

  1. Misfiring of the spark plug
  2. Spontaneous self-ignition of the unburned end gas ahead of the flame front, causing pressure waves and noise
  3. Normal combustion
  4. Ignition by a hot spot before the spark
Show answer & solution

Answer: (B) Spontaneous self-ignition of the unburned end gas ahead of the flame front, causing pressure waves and noise

It causes a very high rate of pressure rise.

Question 23

According to Ricardo's theory, what causes detonation?

  1. Rapid self-ignition of the last part of the charge to be burned
  2. Low compression ratio
  3. Late spark
  4. Early injection of fuel
Show answer & solution

Answer: (A) Rapid self-ignition of the last part of the charge to be burned

Pressure and temperature rise ahead of the flame front.

Question 24

What is pre-ignition?

  1. Late fuel injection
  2. Delay of the spark
  3. Knocking after the spark
  4. Ignition of the charge by a hot surface in the cylinder before the spark occurs
Show answer & solution

Answer: (D) Ignition of the charge by a hot surface in the cylinder before the spark occurs

Glowing carbon deposits or spark plug electrodes can cause it.

Question 25

Which factors increase the tendency to knock in a petrol engine?

  1. Low intake temperature
  2. Retarded spark and low compression
  3. High compression ratio, advanced spark, high intake and coolant temperature and supercharging
  4. High octane fuel
Show answer & solution

Answer: (C) High compression ratio, advanced spark, high intake and coolant temperature and supercharging

All of these raise end-gas temperature or pressure.

Question 26

How can detonation in a petrol engine be controlled?

  1. By advancing the spark
  2. By retarding the spark, using higher octane fuel and increasing turbulence
  3. By increasing compression ratio
  4. By heating the intake air
Show answer & solution

Answer: (B) By retarding the spark, using higher octane fuel and increasing turbulence

Turbulence speeds up flame travel through the end gas.

Question 27

Why does carbon deposition in a petrol engine cylinder increase knocking?

  1. It cools the cylinder
  2. It lowers compression ratio
  3. It reduces clearance volume, raising the effective compression ratio, and forms hot spots
  4. It increases octane number
Show answer & solution

Answer: (C) It reduces clearance volume, raising the effective compression ratio, and forms hot spots

Carbon deposits should be removed periodically.

Question 28

Why must spark timing be advanced as engine speed increases?

  1. To reduce knocking
  2. To cool the engine
  3. To reduce power
  4. The combustion takes roughly fixed time, so the spark must occur earlier in crank angle at higher speed
Show answer & solution

Answer: (D) The combustion takes roughly fixed time, so the spark must occur earlier in crank angle at higher speed

Centrifugal advance mechanisms do this automatically.

Question 29

What compounds formed during pre-flame reactions are associated with detonation?

  1. Peroxides, aldehydes and ketones
  2. Water and carbon dioxide
  3. Salts
  4. Nitrogen and argon
Show answer & solution

Answer: (A) Peroxides, aldehydes and ketones

They make the end gas prone to self-ignition.

Question 30

What is the effect of supercharging a petrol engine on knocking?

  1. It has no effect
  2. It increases the knocking tendency
  3. It reduces octane requirement
  4. It eliminates knocking
Show answer & solution

Answer: (B) It increases the knocking tendency

Higher intake pressure and temperature favour detonation.

Question 31

What happens if diesel is accidentally put into the fuel tank of a petrol engine?

  1. The engine runs better
  2. The engine will not run properly, because diesel does not vaporise and ignite well with a spark
  3. Nothing happens
  4. The engine becomes more efficient
Show answer & solution

Answer: (B) The engine will not run properly, because diesel does not vaporise and ignite well with a spark

Diesel has low volatility.

Question 32

Why is LPG or CNG used as a fuel in many vehicles in Pakistan?

  1. They have higher octane than any liquid fuel and need no tank
  2. They are liquids at room temperature
  3. They need no engine modification
  4. They are cheaper gaseous fuels that burn cleanly in modified petrol engines
Show answer & solution

Answer: (D) They are cheaper gaseous fuels that burn cleanly in modified petrol engines

CNG is mainly methane, and LPG is mainly propane and butane.

Question 33

Why was tetraethyl lead removed from petrol?

  1. It increased knocking
  2. It reduced octane
  3. Lead is toxic and damages catalytic converters
  4. It was too expensive
Show answer & solution

Answer: (C) Lead is toxic and damages catalytic converters

Unleaded petrol uses other octane boosters.

Question 34

What is the function of the float in a carburettor?

  1. To keep the fuel level in the float chamber constant
  2. To start the engine
  3. To control speed
  4. To mix fuel and air
Show answer & solution

Answer: (A) To keep the fuel level in the float chamber constant

A needle valve opens and closes with the float.

Question 35

At what level is the top of the fuel jet kept relative to the fuel level in the float chamber?

  1. Well below it
  2. Far above it
  3. Slightly above it
  4. At exactly the same level
Show answer & solution

Answer: (C) Slightly above it

This prevents fuel dribbling when the engine is stopped.

Question 36

What is the auto-ignition temperature of a fuel?

  1. The flash point
  2. The pour point
  3. The boiling point
  4. The temperature at which it ignites by itself without a spark or flame
Show answer & solution

Answer: (D) The temperature at which it ignites by itself without a spark or flame

Petrol has a higher auto-ignition temperature than diesel.

Question 37

What is the effect of higher self-ignition temperature of a fuel on detonation in a petrol engine?

  1. It causes pre-ignition
  2. It reduces detonation
  3. It has no effect
  4. It increases detonation
Show answer & solution

Answer: (B) It reduces detonation

End gas is less likely to ignite spontaneously.

Question 38

What are the stages of combustion in an SI engine according to Ricardo?

  1. Ignition lag, flame propagation and after-burning
  2. Delay, rapid and controlled combustion
  3. Compression and expansion only
  4. Suction and exhaust
Show answer & solution

Answer: (A) Ignition lag, flame propagation and after-burning

The flame spreads from the spark plug across the chamber.

Question 39

Why is turbulence important in SI engine combustion?

  1. It increases flame speed and reduces the chance of knocking
  2. It cools the mixture
  3. It slows combustion
  4. It prevents ignition
Show answer & solution

Answer: (A) It increases flame speed and reduces the chance of knocking

Combustion chambers are shaped to create squish and swirl.

Question 40

Where should the spark plug be placed in an SI combustion chamber?

  1. At the coolest corner
  2. Inside the piston
  3. Near the centre or hottest part, so that the flame travel distance is short
  4. In the exhaust port
Show answer & solution

Answer: (C) Near the centre or hottest part, so that the flame travel distance is short

Short flame paths reduce knocking.

Question 41

What is the effect of increasing coolant temperature on knocking in a petrol engine?

  1. It reduces knocking
  2. It has no effect
  3. It eliminates knocking
  4. It increases the tendency to knock
Show answer & solution

Answer: (D) It increases the tendency to knock

Hotter walls heat the end gas.

Practice these 41 questions interactively →