What is indicated power?
Show answer & solution
Answer: (D) The power developed inside the engine cylinder by the gases
It is found from the indicator diagram.
Mechanical Engineering · Internal Combustion Engines
39 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is indicated power?
Answer: (D) The power developed inside the engine cylinder by the gases
It is found from the indicator diagram.
What is brake power?
Answer: (B) The useful power available at the engine crankshaft
It is measured with a dynamometer.
What is friction power?
Answer: (D) The difference between indicated power and brake power
It includes pumping and mechanical losses.
What is mechanical efficiency of an engine?
Answer: (B) The ratio of brake power to indicated power
It is typically about 80–90%.
What is brake thermal efficiency?
Answer: (C) The ratio of brake power to the heat energy supplied by the fuel
It is about 25–30% for petrol engines and 30–40% for diesel engines.
What is relative efficiency of an engine?
Answer: (A) The ratio of indicated thermal efficiency to the air-standard cycle efficiency
It shows how close the engine is to its ideal cycle.
What is volumetric efficiency?
Answer: (C) The ratio of the actual volume of fresh charge drawn in to the swept volume, at intake conditions
It is usually about 75–90% for naturally aspirated engines.
What is mean effective pressure?
Answer: (A) The average pressure which, acting on the piston throughout the power stroke, would produce the same work as the actual cycle
It is found from the area of the indicator diagram.
How is indicated power calculated from mean effective pressure?
Answer: (D) IP = pm L A n k / 60, where n is power strokes per minute per cylinder and k the number of cylinders
For a four-stroke engine, n = N/2.
What does an engine indicator measure?
Answer: (B) The variation of cylinder pressure during the cycle, giving mean effective pressure and indicated power
Modern engines use electronic pressure transducers.
What is the Morse test used for?
Answer: (B) Finding indicated power and friction power of a multi-cylinder engine by cutting off cylinders one at a time
Speed is restored with the dynamometer after each cut-off.
What is Willan's line method used for?
Answer: (A) Finding friction power of a diesel engine by extrapolating fuel consumption against brake power to zero fuel
It is not suitable for petrol engines.
What is specific fuel consumption?
Answer: (D) The fuel consumed per unit of power output per hour
Diesel engines have lower specific fuel consumption than petrol engines.
What is the approximate brake specific fuel consumption of a diesel engine?
Answer: (B) About 0.2 kg per kWh (or per bhp-hour, depending on engine)
Petrol engines consume roughly 0.25–0.3 kg per kWh.
What does a heat balance sheet of an engine show?
Answer: (C) How the heat supplied by fuel is distributed among brake power, cooling water, exhaust gases and other losses
Typically only about a third of the heat becomes useful work.
What is supercharging?
Answer: (C) Supplying intake air at a density greater than atmospheric to increase engine power
It allows more fuel to be burned per cycle.
What is a turbocharger?
Answer: (D) A supercharger driven by an exhaust-gas turbine
It recovers energy from exhaust gases.
Why is an intercooler used with a turbocharger?
Answer: (A) To cool the compressed air, increasing its density and reducing knock
Denser air gives more power.
Where is supercharging essential?
Answer: (C) In aircraft engines operating at high altitudes
Air density falls with altitude.
Why is supercharging more commonly applied to diesel engines than to petrol engines?
Answer: (A) It improves combustion in diesel engines, while in petrol engines it increases knocking
Turbocharged diesels are standard in trucks.
Does supercharging improve the fuel economy of an engine in itself?
Answer: (B) Not necessarily; its main purpose is to increase power and reduce weight and bulk for a given output
Turbocharging can improve overall efficiency by using exhaust energy.
What type of governing is used in petrol engines?
Answer: (D) Quantity governing, by varying the quantity of mixture with the throttle
The air–fuel ratio remains nearly constant.
What type of governing is used in diesel engines?
Answer: (C) Quality governing, by varying the quantity of fuel injected while air supply stays nearly constant
The air–fuel ratio changes with load.
An engine runs at 1000 rpm at no load and 960 rpm at full load. What is the speed droop?
Answer: (B) About 4%
(1000 − 960) ÷ 960 ≈ 4.2%.
What is the speed droop of an isochronous governor?
Answer: (A) Zero
An isochronous governor keeps the same speed at all loads.
How does increasing intake air temperature affect engine power and efficiency?
Answer: (D) It reduces power and efficiency
Hot air is less dense, reducing the mass of charge.
How does back pressure in the exhaust affect fuel consumption?
Answer: (D) Higher back pressure increases fuel consumption
The piston does more work pushing out exhaust.
Why are diesel engines more economical than petrol engines at part load?
Answer: (A) They are quality governed with no throttling losses and use higher compression ratios
Petrol engines lose efficiency at part throttle.
What is the typical overall thermal efficiency of IC engines?
Answer: (B) About 30–35%
Large diesel engines can exceed 45%.
What is the brake power of an engine in terms of torque T and speed N?
Answer: (B) BP = 2πNT/60
BP is in watts when T is in N·m and N in rpm.
What is brake mean effective pressure (bmep)?
Answer: (D) The mean effective pressure calculated from brake power
It allows engines of different sizes to be compared.
What is a dynamometer used for in engine testing?
Answer: (C) Measuring the torque and brake power of the engine
Hydraulic, eddy-current and electrical dynamometers are common.
How does volumetric efficiency change at very high engine speeds?
Answer: (B) It decreases because there is less time to fill the cylinder
Valve timing and intake design are tuned to improve it.
What is the air–fuel ratio of a diesel engine at full load, roughly?
Answer: (C) About 18–25:1
At light loads, it may exceed 60:1.
What is the approximate percentage of fuel energy converted into useful work in a typical car engine?
Answer: (B) About 25–35%
Most of the rest goes to coolant and exhaust.
What is the motoring test used for?
Answer: (A) Measuring friction power by driving the engine with an electric motor without firing
The engine is kept at operating temperature.
What is the main reason petrol engines lose efficiency at part load?
Answer: (D) Throttling causes pumping losses
Diesel engines do not throttle intake air.
What is hit-and-miss governing?
Answer: (D) Cutting off fuel supply completely on some cycles to control speed
It was used in old gas engines.
How does cooling water temperature affect diesel engine fuel consumption at light loads?
Answer: (C) Small changes in cooling and friction have a large relative effect, which is why guarantees are not given at very low loads
Fuel use at quarter load is less predictable.