What is unsteady (transient) heat conduction?
Show answer & solution
Answer: (C) Conduction in which temperature at points in the body changes with time
Quenching of steel is an example.
Mechanical Engineering · Heat Transfer
30 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is unsteady (transient) heat conduction?
Answer: (C) Conduction in which temperature at points in the body changes with time
Quenching of steel is an example.
What is the Biot number?
Answer: (D) The ratio of internal conduction resistance to external convection resistance, Bi = hL/k
k is the thermal conductivity of the solid.
When is the lumped heat capacity method valid?
Answer: (A) When the Biot number is less than about 0.1
Then temperature inside the body is nearly uniform.
What is the Fourier number?
Answer: (B) A dimensionless time, αt/L², used in transient conduction
Large Fourier numbers mean heat has penetrated deeply.
What is the time constant of a thermocouple?
Answer: (B) The time it takes to reach 63.2% of the initial temperature difference
τ = ρcV/(hA).
How can the response of a thermocouple be made faster?
Answer: (A) By using a smaller junction with a high surface-to-volume ratio
A small time constant gives quick response.
Which instrument is suitable for measuring steam temperature of about 540 °C?
Answer: (C) Thermocouple
Thermocouples cover a wide range of temperatures.
What are Heisler charts used for?
Answer: (D) Finding temperature distribution in transient conduction for slabs, cylinders and spheres
They are used when lumped analysis is not valid.
What is the purpose of fins (extended surfaces)?
Answer: (B) To increase the surface area and so increase the rate of heat transfer by convection
Motorcycle engines and car radiators use fins.
On which side of a heat exchanger wall are fins most effective?
Answer: (A) On the side with the lower heat transfer coefficient, such as the air side
Fins compensate for the weak convection of gases.
What is fin efficiency?
Answer: (C) The ratio of actual heat transferred by the fin to the heat it would transfer if its whole surface were at the base temperature
It decreases as fin length increases.
What is fin effectiveness?
Answer: (D) The ratio of heat transfer with the fin to heat transfer without the fin from the same base area
Fins are justified only if effectiveness is well above 1, usually above 2.
What makes a fin material most suitable?
Answer: (B) High thermal conductivity, such as aluminium or copper
Heat must flow easily along the fin.
Why is there little benefit in making fins very long?
Answer: (D) The fin tip approaches the surrounding temperature, so additional length transfers little extra heat
Fin efficiency drops with length.
What is a common assumption for a fin with a very long length?
Answer: (C) The fin tip temperature equals the surrounding fluid temperature
Other cases assume an insulated or convecting tip.
Which of the following is a case of steady-state heat transfer?
Answer: (A) Heat flow through the wall of a furnace operating at constant temperatures for a long time
Steady state means temperatures do not change with time.
What does a small Biot number indicate?
Answer: (B) Internal conduction resistance is small compared with surface convection resistance, so the body has nearly uniform temperature
Small metal parts in air often have small Biot numbers.
In the lumped capacity method, how does the temperature of a body change with time when suddenly exposed to a fluid?
Answer: (C) Exponentially towards the fluid temperature
(T − T∞)/(Ti − T∞) = e^(−t/τ).
What is the characteristic length used in lumped analysis?
Answer: (A) Volume divided by surface area (V/A)
For a sphere, V/A = r/3.
How does a material with high thermal diffusivity respond to a sudden temperature change at its surface?
Answer: (D) Its interior temperature changes quickly
Metals have higher diffusivity than insulating materials.
What is a semi-infinite solid in transient conduction?
Answer: (A) A body that extends to infinity in one direction from a surface, so heat effects do not reach the far side
The ground below the surface is often treated as semi-infinite.
Why are fins made thin?
Answer: (C) To give a large surface area for a small amount of material while keeping the temperature drop along them small
Thin fins are closely spaced to increase total area.
What is the main limitation on fin spacing?
Answer: (B) Fins placed too close together restrict fluid flow and reduce the heat transfer coefficient
Optimum spacing balances area and flow.
Which shape of fin uses material most efficiently for a given heat transfer?
Answer: (D) A tapered (triangular or parabolic) profile
Less material is needed at the tip where temperature is lower.
Where are pin fins commonly used?
Answer: (B) On electronic heat sinks
They allow air to flow in any direction.
What is the effect of increasing the heat transfer coefficient on fin efficiency?
Answer: (C) It reduces fin efficiency
The tip cools more quickly relative to the base.
What is the analogy between heat conduction and electricity?
Answer: (A) Temperature difference corresponds to voltage, heat flow to current and thermal resistance to electrical resistance
It allows network methods to be used.
What does heat generation inside a body, such as in an electric wire, cause?
Answer: (D) A temperature that is highest at the centre of the body
Nuclear fuel rods and electric heaters have internal heat generation.
What is the maximum temperature location in a plane wall with uniform heat generation and both faces at the same temperature?
Answer: (A) The mid-plane of the wall
Heat flows outward from the centre to both faces.
What is the main use of insulating firebricks in furnaces?
Answer: (D) Reducing heat loss through the furnace walls
They have low conductivity and can withstand high temperatures.