Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Heat Transfer: Convection

Mechanical Engineering · Heat Transfer

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does Newton's law of cooling state?

  1. Heat flow is proportional to thickness
  2. Heat flow is proportional to T⁴
  3. The rate of heat transfer by convection is proportional to the surface area and the temperature difference between surface and fluid
  4. Heat flow is independent of area
Show answer & solution

Answer: (C) The rate of heat transfer by convection is proportional to the surface area and the temperature difference between surface and fluid

q = hA(Ts − T∞).

Question 2

What is the unit of the convective heat transfer coefficient?

  1. W/m²·K
  2. J/kg·K
  3. W/K
  4. W/m·K
Show answer & solution

Answer: (A) W/m²·K

It is also called the film coefficient.

Question 3

What is the difference between free and forced convection?

  1. Free convection uses a fan
  2. Forced convection needs no fluid motion
  3. They are the same
  4. Free convection is caused by density differences due to temperature, while forced convection uses a pump or fan to move the fluid
Show answer & solution

Answer: (D) Free convection is caused by density differences due to temperature, while forced convection uses a pump or fan to move the fluid

Forced convection gives much higher heat transfer coefficients.

Question 4

What is a typical range of heat transfer coefficient for free convection in air?

  1. About 0.01 W/m²·K
  2. About 5–25 W/m²·K
  3. About 50 000 W/m²·K
  4. About 1000–5000 W/m²·K
Show answer & solution

Answer: (B) About 5–25 W/m²·K

Boiling and condensation give the highest coefficients.

Question 5

Which process usually gives the highest heat transfer coefficient?

  1. Conduction in insulation
  2. Free convection in air
  3. Condensation or boiling of water
  4. Forced convection in air
Show answer & solution

Answer: (C) Condensation or boiling of water

Phase change involves large latent heat.

Question 6

What is the Nusselt number?

  1. The ratio of inertia to viscous forces
  2. The ratio of momentum to thermal diffusivity
  3. The ratio of buoyancy to viscous forces
  4. The ratio of convective heat transfer to conductive heat transfer across a fluid layer, Nu = hL/k
Show answer & solution

Answer: (D) The ratio of convective heat transfer to conductive heat transfer across a fluid layer, Nu = hL/k

k here is the conductivity of the fluid.

Question 7

What is the Prandtl number?

  1. The ratio of momentum diffusivity to thermal diffusivity, Pr = μcp/k
  2. The ratio of inertia to viscous forces
  3. The ratio of convection to conduction
  4. The ratio of buoyancy to viscous forces
Show answer & solution

Answer: (A) The ratio of momentum diffusivity to thermal diffusivity, Pr = μcp/k

It depends only on fluid properties.

Question 8

What is the approximate Prandtl number of air?

  1. 0.01
  2. 0.7
  3. 7
  4. 70
Show answer & solution

Answer: (B) 0.7

Water has a Prandtl number of about 7 at room temperature.

Question 9

For which fluids is the Prandtl number very small?

  1. Water
  2. Air
  3. Oils
  4. Liquid metals
Show answer & solution

Answer: (D) Liquid metals

Liquid metals have very high thermal conductivity.

Question 10

For which fluids is the Prandtl number very large?

  1. Liquid metals
  2. Hydrogen gas
  3. Heavy oils
  4. Air
Show answer & solution

Answer: (C) Heavy oils

Their momentum diffuses much faster than heat.

Question 11

What is the Grashof number?

  1. The ratio of buoyancy forces to viscous forces in free convection
  2. The ratio of convection to conduction
  3. The ratio of momentum to thermal diffusivity
  4. The ratio of inertia to viscous forces
Show answer & solution

Answer: (A) The ratio of buoyancy forces to viscous forces in free convection

It plays the role of Reynolds number in free convection.

Question 12

Which dimensionless numbers govern the Nusselt number in free convection?

  1. Reynolds and Prandtl numbers
  2. Grashof and Prandtl numbers
  3. Reynolds and Mach numbers
  4. Biot and Fourier numbers
Show answer & solution

Answer: (B) Grashof and Prandtl numbers

Nu = f(Gr, Pr).

Question 13

Which dimensionless numbers govern the Nusselt number in forced convection?

  1. Grashof and Prandtl numbers
  2. Reynolds and Prandtl numbers
  3. Mach and Weber numbers
  4. Biot and Fourier numbers
Show answer & solution

Answer: (B) Reynolds and Prandtl numbers

Nu = f(Re, Pr).

Question 14

What is the Rayleigh number?

  1. The product of Reynolds and Prandtl numbers
  2. The Biot number squared
  3. The product of Grashof and Prandtl numbers
  4. The ratio of Nusselt to Reynolds number
Show answer & solution

Answer: (C) The product of Grashof and Prandtl numbers

It decides the onset of natural convection.

Question 15

What is the Stanton number?

  1. Re × Pr
  2. hL/k
  3. Gr × Pr
  4. Nu/(Re × Pr)
Show answer & solution

Answer: (D) Nu/(Re × Pr)

It is used in the Reynolds analogy.

Question 16

What is the Peclet number?

  1. The product of Reynolds and Prandtl numbers
  2. The product of Grashof and Prandtl numbers
  3. The ratio of Nusselt to Prandtl numbers
  4. The ratio of conduction to radiation
Show answer & solution

Answer: (A) The product of Reynolds and Prandtl numbers

It compares convection with conduction.

Question 17

What does the Dittus–Boelter equation give?

  1. The time constant of thermocouples
  2. The radiation between surfaces
  3. The Nusselt number for fully developed turbulent flow in tubes, Nu = 0.023 Re^0.8 Pr^n
  4. The heat flux in boiling
Show answer & solution

Answer: (C) The Nusselt number for fully developed turbulent flow in tubes, Nu = 0.023 Re^0.8 Pr^n

n is 0.4 for heating and 0.3 for cooling of the fluid.

Question 18

What is the Nusselt number for fully developed laminar flow in a circular tube with constant wall temperature?

  1. About 0.023
  2. About 3.66
  3. About 4.36
  4. About 100
Show answer & solution

Answer: (B) About 3.66

With constant heat flux, it is about 4.36.

Question 19

What is the thermal boundary layer?

  1. The free stream
  2. The region of velocity change
  3. The solid wall
  4. The region near a surface in which fluid temperature changes from the surface temperature to the free-stream temperature
Show answer & solution

Answer: (D) The region near a surface in which fluid temperature changes from the surface temperature to the free-stream temperature

Its thickness compared with the velocity boundary layer depends on Prandtl number.

Question 20

When are the velocity and thermal boundary layers of equal thickness?

  1. When the Prandtl number is 1
  2. When the Prandtl number is 0
  3. When the Reynolds number is 1
  4. When the Grashof number is 1
Show answer & solution

Answer: (A) When the Prandtl number is 1

For Pr > 1, the thermal boundary layer is thinner.

Question 21

By what mode does heat pass through the thin laminar sub-layer next to a tube wall in turbulent flow?

  1. Radiation only
  2. Boiling
  3. Convection by eddies
  4. Conduction
Show answer & solution

Answer: (D) Conduction

This sub-layer often forms the main resistance to heat transfer.

Question 22

What does the Reynolds analogy relate?

  1. Boiling to condensation
  2. Heat transfer to fluid friction
  3. Radiation to conduction
  4. Mass to energy
Show answer & solution

Answer: (B) Heat transfer to fluid friction

It applies best when Pr is close to 1.

Question 23

Which property of air decreases as its temperature rises at constant pressure?

  1. Viscosity
  2. Thermal conductivity
  3. Density
  4. Specific heat
Show answer & solution

Answer: (C) Density

Viscosity and conductivity of gases increase with temperature.

Question 24

What is the reason for using baffles in a shell-and-tube heat exchanger?

  1. To increase turbulence and the heat transfer coefficient on the shell side, and to support the tubes
  2. To reduce flow velocity
  3. To store fluid
  4. To reduce heat transfer
Show answer & solution

Answer: (A) To increase turbulence and the heat transfer coefficient on the shell side, and to support the tubes

They direct the shell fluid across the tubes.

Question 25

Why is forced convection more effective than free convection?

  1. It reduces area
  2. It uses higher temperatures
  3. Higher fluid velocities thin the boundary layer and increase the heat transfer coefficient
  4. It needs no fluid
Show answer & solution

Answer: (C) Higher fluid velocities thin the boundary layer and increase the heat transfer coefficient

Fans and pumps provide the higher velocity.

Question 26

What is the convective heat transfer coefficient mainly dependent on?

  1. Only the wall material
  2. Only the temperature
  3. Fluid properties, flow velocity, surface geometry and type of flow
  4. Only the colour of the surface
Show answer & solution

Answer: (C) Fluid properties, flow velocity, surface geometry and type of flow

It is not a property of the fluid alone.

Question 27

What is the typical range of heat transfer coefficient for forced convection of water?

  1. About 0.01 W/m²·K
  2. About 1 000 000 W/m²·K
  3. About 1–10 W/m²·K
  4. About 300–20 000 W/m²·K
Show answer & solution

Answer: (D) About 300–20 000 W/m²·K

Liquids give much higher coefficients than gases.

Question 28

What causes motion in free (natural) convection?

  1. Wind only
  2. Buoyancy forces from density differences caused by temperature differences
  3. A fan
  4. A pump
Show answer & solution

Answer: (B) Buoyancy forces from density differences caused by temperature differences

Warm, lighter fluid rises and cool, denser fluid sinks.

Question 29

Which dimensionless number decides whether flow in a tube is laminar or turbulent?

  1. Biot number
  2. Prandtl number
  3. Reynolds number
  4. Grashof number
Show answer & solution

Answer: (C) Reynolds number

Flow becomes turbulent above about Re = 2300 in tubes.

Question 30

What is the effect of turbulence on convective heat transfer?

  1. It reduces heat transfer
  2. It greatly increases the heat transfer coefficient
  3. It has no effect
  4. It stops heat transfer
Show answer & solution

Answer: (B) It greatly increases the heat transfer coefficient

Turbulent eddies mix hot and cold fluid.

Question 31

What is the hydrodynamic entrance length?

  1. The distance from the tube inlet required for the velocity profile to become fully developed
  2. The total tube length
  3. The diameter of the tube
  4. The length of the thermal boundary layer only
Show answer & solution

Answer: (A) The distance from the tube inlet required for the velocity profile to become fully developed

Heat transfer coefficients are higher in the entrance region.

Question 32

What is a fully developed thermal flow in a tube?

  1. A flow with zero temperature difference
  2. A flow at the tube inlet
  3. A flow without heat transfer
  4. A flow in which the dimensionless temperature profile no longer changes along the tube
Show answer & solution

Answer: (D) A flow in which the dimensionless temperature profile no longer changes along the tube

The heat transfer coefficient then becomes constant.

Question 33

What is the bulk (mean) temperature of a fluid in a tube?

  1. The wall temperature
  2. The temperature that represents the average thermal energy of the fluid at a section
  3. The inlet temperature
  4. The centre-line temperature only
Show answer & solution

Answer: (B) The temperature that represents the average thermal energy of the fluid at a section

It is used in Newton's law of cooling for internal flow.

Question 34

What is the film temperature used for?

  1. Evaluating fluid properties as the average of the surface and free-stream temperatures
  2. Calculating LMTD
  3. Measuring wall temperature
  4. Measuring radiation
Show answer & solution

Answer: (A) Evaluating fluid properties as the average of the surface and free-stream temperatures

Tf = (Ts + T∞)/2.

Question 35

What is the main mechanism of heat transfer from a domestic radiator to a room?

  1. Conduction through air only
  2. Boiling
  3. Natural convection, with some radiation
  4. Forced convection only
Show answer & solution

Answer: (C) Natural convection, with some radiation

Despite its name, much of its heat is convected.

Question 36

Why does a fan make us feel cooler in summer?

  1. It reduces humidity to zero
  2. It increases convective heat transfer and evaporation from the skin
  3. It produces cold air
  4. It lowers the room temperature directly
Show answer & solution

Answer: (B) It increases convective heat transfer and evaporation from the skin

Moving air thins the boundary layer near the skin.

Question 37

What is the wind chill effect?

  1. Freezing of water by wind
  2. Heating by wind
  3. The increased rate of heat loss from the body caused by wind, making it feel colder
  4. A drop in air temperature due to wind
Show answer & solution

Answer: (C) The increased rate of heat loss from the body caused by wind, making it feel colder

It is due to forced convection.

Question 38

How does the Nusselt number for turbulent flow in a tube vary with Reynolds number, according to Dittus–Boelter?

  1. Nu ∝ Re²
  2. Nu ∝ Re
  3. Nu is independent of Re
  4. Nu ∝ Re^0.8
Show answer & solution

Answer: (D) Nu ∝ Re^0.8

Higher velocity gives higher heat transfer coefficients.

Question 39

What is the effect of fluid viscosity on convective heat transfer in a given flow?

  1. Higher viscosity generally reduces the heat transfer coefficient
  2. Viscosity makes it infinite
  3. Viscosity has no effect
  4. Higher viscosity increases it greatly
Show answer & solution

Answer: (A) Higher viscosity generally reduces the heat transfer coefficient

Viscous fluids have thicker boundary layers.

Question 40

What is the principle of a hot-wire anemometer?

  1. Boiling on a wire
  2. Conduction along a wire
  3. The cooling rate of a heated wire depends on the velocity of the gas flowing over it
  4. Radiation from a wire
Show answer & solution

Answer: (C) The cooling rate of a heated wire depends on the velocity of the gas flowing over it

It measures gas velocity through forced convection.

Practice these 40 questions interactively →