What are the three modes of heat transfer?
Show answer & solution
Answer: (D) Conduction, convection and radiation
Heat always flows from higher to lower temperature.
Mechanical Engineering · Heat Transfer
44 questions, each with the answer and a worked solution.
Practice interactively and track your score →What are the three modes of heat transfer?
Answer: (D) Conduction, convection and radiation
Heat always flows from higher to lower temperature.
According to which law of thermodynamics does heat flow from a hotter body to a colder body?
Answer: (B) Second law
Heat flows only when there is a temperature difference.
What is conduction?
Answer: (C) Transfer of heat through a material by molecular collisions and free electrons, without bulk movement of the material
It is the main mode of heat transfer in solids.
What is convection?
Answer: (A) Transfer of heat by the bulk motion of a fluid combined with conduction
It is the main mode of heat transfer in liquids and gases.
What is radiation heat transfer?
Answer: (C) Transfer of heat by electromagnetic waves, which can travel through a vacuum
Heat from the Sun reaches the Earth by radiation.
In which device does heat transfer take place by all three modes: conduction, convection and radiation?
Answer: (B) A boiler
Furnace gases radiate and convect heat to tubes, and heat conducts through the tube walls.
What does Fourier's law of heat conduction state?
Answer: (A) The rate of heat conduction is proportional to the area and the temperature gradient in the direction of heat flow
q = −kA (dT/dx).
What is thermal conductivity?
Answer: (D) The heat conducted per unit time through unit area and unit thickness for a unit temperature difference
It is a property of the material.
What is the SI unit of thermal conductivity?
Answer: (B) W/m·K
In MKS units it is kcal/m·hr·°C.
Which of the following materials has the highest thermal conductivity?
Answer: (A) Copper
Silver has a slightly higher conductivity than copper.
What is the approximate thermal conductivity of pure copper?
Answer: (D) About 385–400 W/m·K
Aluminium is about 205 W/m·K and mild steel about 50 W/m·K.
Which of the following has the lowest thermal conductivity?
Answer: (C) Air
Still air is an excellent insulator, about 0.026 W/m·K.
What is the approximate thermal conductivity of water at room temperature?
Answer: (B) About 0.6 W/m·K
It is much higher than that of air.
Why are metals good conductors of heat?
Answer: (A) Free electrons carry thermal energy rapidly through the lattice
Good electrical conductors are usually good thermal conductors.
How does the thermal conductivity of most pure metals change with increasing temperature?
Answer: (D) It decreases
Lattice vibrations scatter the free electrons more at higher temperatures.
How does the thermal conductivity of gases such as air change with increasing temperature?
Answer: (C) It increases
Faster molecules transfer energy more quickly.
How does the thermal conductivity of non-metallic amorphous solids change as temperature decreases?
Answer: (D) It decreases
Insulating materials generally conduct less at low temperature.
Why is cork a good heat insulator?
Answer: (A) Its porous structure traps air
Trapped air has very low thermal conductivity.
How does moisture affect the insulating ability of an insulating material?
Answer: (B) It reduces it
Water conducts heat much better than trapped air.
What prevents moisture from entering insulation on cold pipes due to vapour pressure?
Answer: (C) A vapour barrier (vapour seal)
Condensed moisture would ruin the insulation.
What is the thermal resistance of a plane wall of thickness L, area A and conductivity k?
Answer: (D) L/(kA)
Thermal resistances in series are added.
For two walls of equal thickness and area with thermal conductivities in the ratio 2:1, what is the ratio of heat flows for the same temperature difference?
Answer: (C) 2:1
Heat flow is directly proportional to thermal conductivity.
On which factor does conduction heat flow depend inversely?
Answer: (B) Thickness of the material
q = kAΔT/L.
What is thermal conductance?
Answer: (A) Thermal conductivity divided by thickness (k/L)
It is the heat flow per unit area per unit temperature difference.
How is heat flow through a composite wall of several layers calculated?
Answer: (A) By dividing the overall temperature difference by the sum of the thermal resistances of the layers
It is analogous to resistances in series in an electric circuit.
What is the thermal resistance of a hollow cylinder of length L, inner radius r₁ and outer radius r₂?
Answer: (C) ln(r₂/r₁)/(2πkL)
Heat flows radially through pipe walls and insulation.
What is contact (interface) thermal resistance?
Answer: (B) Additional resistance at the joint between two surfaces due to imperfect contact
Thermal paste reduces contact resistance in electronics.
What is the critical radius of insulation for a cylinder?
Answer: (D) k/h, where k is the insulation conductivity and h the outer heat transfer coefficient
Heat loss is maximum when insulation radius equals the critical radius.
What is the critical radius of insulation for a sphere?
Answer: (C) 2k/h
It is twice the value for a cylinder.
What happens when insulation is added to a small pipe or wire whose radius is less than the critical radius?
Answer: (D) Heat loss increases until the critical radius is reached
This is why electric cables can be cooled better by a thin insulating layer.
When a steam pipe is to be insulated with two materials of different conductivities, which arrangement gives the least heat loss?
Answer: (A) The better insulating material is placed next to the pipe
The inner layer has a smaller area and more effect on resistance.
What is thermal diffusivity?
Answer: (B) The ratio of thermal conductivity to the product of density and specific heat (α = k/ρc)
It shows how quickly temperature changes spread through a material.
What is the SI unit of thermal diffusivity?
Answer: (B) m²/s
It has the same unit as kinematic viscosity.
How is thermal diffusivity related to thermal conductivity, density and specific heat?
Answer: (C) It is directly proportional to conductivity and inversely proportional to density and specific heat
α = k/(ρc).
What is the general heat conduction equation in Cartesian coordinates for steady state without heat generation?
Answer: (A) Laplace's equation ∇²T = 0
With heat generation, it becomes Poisson's equation.
What is steady-state heat conduction?
Answer: (D) Conduction in which temperatures at all points do not change with time
Heating or cooling a body from cold start is unsteady.
What is the heat flow through a 0.2 m thick wall of area 10 m² with k = 1 W/m·K and a temperature difference of 20 °C?
Answer: (C) 1000 W
q = kAΔT/L = 1 × 10 × 20 ÷ 0.2.
Which material is commonly used for thermal insulation of steam pipes?
Answer: (B) Glass wool or mineral wool
They trap air in fine fibres.
Why does the thermal conductivity of glass wool vary between samples?
Answer: (A) It depends on density, fibre size and amount of trapped air
Very low or very high densities both give poorer insulation.
What is the thermal conductivity of diamond compared with metals?
Answer: (C) It is higher than that of copper
Diamond conducts heat through lattice vibrations.
Which law describes heat transfer from a solid surface to a moving fluid?
Answer: (B) Newton's law of cooling
Fourier's law describes conduction.
Heat flow through a body by conduction depends on which factors?
Answer: (D) Thermal conductivity, area, temperature difference and thickness
q = kAΔT/L.
What is heat flux?
Answer: (A) The rate of heat transfer per unit area
Its unit is W/m².
Why are cooking pans often made of aluminium or copper with plastic handles?
Answer: (B) The metals conduct heat well to the food, while plastic handles insulate the hand
Different conductivities suit different purposes.