What is a heat exchanger?
Show answer & solution
Answer: (B) A device that transfers heat between two or more fluids at different temperatures
Radiators, condensers and evaporators are heat exchangers.
Mechanical Engineering · Heat Transfer
39 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a heat exchanger?
Answer: (B) A device that transfers heat between two or more fluids at different temperatures
Radiators, condensers and evaporators are heat exchangers.
What is a recuperator?
Answer: (A) A heat exchanger in which hot and cold fluids flow simultaneously, separated by a solid wall
Shell-and-tube exchangers are recuperators.
What is a regenerator?
Answer: (D) A heat exchanger in which hot and cold fluids flow alternately over the same surface or matrix
The matrix stores heat from the hot fluid and releases it to the cold fluid.
What is a direct-contact heat exchanger?
Answer: (D) One in which hot and cold fluids mix directly
Cooling towers and open feed-water heaters are examples.
What is a parallel flow heat exchanger?
Answer: (B) One in which hot and cold fluids enter at the same end and flow in the same direction
The temperature difference is largest at the inlet.
What is a counter-flow heat exchanger?
Answer: (C) One in which hot and cold fluids flow in opposite directions
It is the most effective flow arrangement.
What is a cross-flow heat exchanger?
Answer: (A) One in which the two fluids flow at right angles to each other
Car radiators are cross-flow exchangers.
Which flow arrangement gives the highest heat transfer for the same inlet temperatures and area?
Answer: (D) Counter flow
Counter flow keeps a more uniform temperature difference.
How does the LMTD of counter flow compare with parallel flow for the same terminal temperatures?
Answer: (A) It is higher
A higher LMTD means less area is needed.
In which heat exchanger arrangement can the outlet temperature of the cold fluid exceed the outlet temperature of the hot fluid?
Answer: (B) Counter flow
In parallel flow, the cold outlet always stays below the hot outlet.
What is the log mean temperature difference (LMTD)?
Answer: (C) (ΔT₁ − ΔT₂)/ln(ΔT₁/ΔT₂), where ΔT₁ and ΔT₂ are the temperature differences at the two ends
It gives the effective average temperature difference.
What is the basic design equation of a heat exchanger?
Answer: (C) Q = U A ΔT_lm
U is the overall heat transfer coefficient.
What is the overall heat transfer coefficient (U)?
Answer: (D) A coefficient that combines all thermal resistances between two fluids separated by a wall
1/U = 1/h₁ + t/k + 1/h₂ for a plane wall.
For which combination of heat transfer modes is the overall heat transfer coefficient normally used?
Answer: (B) Conduction and convection
It combines wall conduction with convection on both sides.
What is fouling in heat exchangers?
Answer: (A) Deposits of scale, dirt or corrosion products on surfaces that add thermal resistance
A fouling factor is included in design.
What does the effectiveness of a heat exchanger mean?
Answer: (C) The ratio of actual heat transfer to the maximum possible heat transfer
It lies between 0 and 1.
What is NTU in heat exchanger analysis?
Answer: (B) The number of transfer units, UA/Cmin
Higher NTU gives higher effectiveness.
When is the effectiveness–NTU method preferred to the LMTD method?
Answer: (A) When outlet temperatures are unknown and must be found
The LMTD method is convenient for sizing when temperatures are known.
When one fluid in a heat exchanger is condensing or evaporating at constant temperature, how do parallel and counter flow compare?
Answer: (D) They give the same performance
The heat capacity ratio becomes zero.
What is a correction factor (F) used for in heat exchanger design?
Answer: (A) Adjusting the counter-flow LMTD for multipass and cross-flow arrangements
Q = U A F ΔT_lm,cf.
What is a compact heat exchanger?
Answer: (B) An exchanger with a very large surface area per unit volume, such as a car radiator
Fins on thin tubes provide large area.
What is a shell-and-tube heat exchanger?
Answer: (D) One fluid flows through a bundle of tubes while the other flows in the shell around them
It is the most common industrial heat exchanger.
What is a plate heat exchanger?
Answer: (C) An exchanger made of thin corrugated plates that form channels for the two fluids
It is compact and easy to clean, and used in dairies.
What is an economiser in a boiler plant?
Answer: (D) A heat exchanger that preheats boiler feed water using flue gases
It improves boiler efficiency.
What is an air preheater in a boiler plant?
Answer: (C) A heat exchanger that heats combustion air using flue gases
Rotary regenerative (Ljungström) air preheaters are common.
In a counter-flow heat exchanger, where are both fluids at their hottest?
Answer: (A) At the end where the hot fluid enters and the cold fluid leaves
The cold fluid leaves at the hot fluid's entry end.
Hot fluid enters at 200 °C and leaves at 120 °C, while cold fluid enters at 40 °C and leaves at 100 °C in counter flow. What are the terminal temperature differences?
Answer: (B) 100 °C and 80 °C
At one end: 200 − 100; at the other end: 120 − 40.
What is the main advantage of a counter-flow heat exchanger?
Answer: (A) It needs less heat transfer area for the same duty and allows closer temperature approach
It is preferred where high effectiveness is required.
What is a condenser in a steam power plant?
Answer: (C) A heat exchanger in which exhaust steam is condensed by cooling water
It maintains low back pressure on the turbine.
What is an evaporator in a refrigeration system?
Answer: (B) A heat exchanger in which refrigerant absorbs heat and evaporates
It produces the refrigerating effect.
What is the function of a cooling tower?
Answer: (C) To cool circulating water by partial evaporation into air
It is a direct-contact heat exchanger.
What is the effect of fouling on the overall heat transfer coefficient?
Answer: (D) It reduces it
Exchangers must be cleaned periodically.
What is the heat capacity rate of a fluid stream?
Answer: (A) The product of mass flow rate and specific heat (ṁcp)
The fluid with the smaller value is Cmin.
Which fluid has the larger temperature change in a heat exchanger?
Answer: (B) The fluid with the smaller heat capacity rate
Heat lost by one equals heat gained by the other.
What is the maximum possible heat transfer in a heat exchanger?
Answer: (D) Cmin × (hot inlet temperature − cold inlet temperature)
It would need an infinitely long counter-flow exchanger.
What is a double-pipe heat exchanger?
Answer: (B) One pipe placed inside another, with one fluid in the inner pipe and the other in the annulus
It is simple and used for small duties.
What is the purpose of multiple tube passes in a shell-and-tube exchanger?
Answer: (C) To increase fluid velocity and heat transfer coefficient inside the tubes
Velocity increase also raises pressure drop.
What is a heat pipe?
Answer: (A) A sealed tube containing a working fluid that transfers heat by evaporation and condensation
It has very high effective thermal conductivity.
In a car radiator, which fluid is on the finned side?
Answer: (D) Air
Fins compensate for the low heat transfer coefficient of air.