Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Machine Design: Threaded Fasteners

Mechanical Engineering · Machine Design

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is a bolt?

  1. A fastener threaded at both ends
  2. A fastener that screws into a tapped hole without a nut
  3. A permanent fastener
  4. A fastener with a head at one end and a thread at the other, used with a nut
Show answer & solution

Answer: (D) A fastener with a head at one end and a thread at the other, used with a nut

Bolts pass through clearance holes in the parts.

Question 2

What is a tap bolt (cap screw)?

  1. A bolt that screws into a tapped hole in one of the parts instead of using a nut
  2. A key
  3. A rivet
  4. A bolt threaded at both ends
Show answer & solution

Answer: (A) A bolt that screws into a tapped hole in one of the parts instead of using a nut

It is used where there is no space for a nut.

Question 3

What is a stud?

  1. A rivet
  2. A rod threaded at both ends, one end screwed into a tapped hole and the other used with a nut
  3. A set screw
  4. A bolt with a head
Show answer & solution

Answer: (B) A rod threaded at both ends, one end screwed into a tapped hole and the other used with a nut

Studs are used for cylinder heads and covers that are removed often.

Question 4

What are set screws used for?

  1. Transmitting large power
  2. Joining two plates permanently
  3. Preventing relative motion between two parts, such as a hub on a shaft
  4. Lifting machines
Show answer & solution

Answer: (C) Preventing relative motion between two parts, such as a hub on a shaft

The point of the set screw presses against the shaft.

Question 5

What are eye bolts used for?

  1. Foundations
  2. Joining plates
  3. Locking nuts
  4. Lifting and transporting machines
Show answer & solution

Answer: (D) Lifting and transporting machines

They are screwed into heavy machines to attach lifting hooks.

Question 6

What is an Allen bolt?

  1. A bolt with a hexagonal socket (depression) in its head for an Allen key
  2. A bolt without threads
  3. A bolt with a square head
  4. A self-locking bolt
Show answer & solution

Answer: (A) A bolt with a hexagonal socket (depression) in its head for an Allen key

It is used where a spanner cannot reach.

Question 7

What does the designation M 33 × 2 mean for a bolt?

  1. 2 threads per mm
  2. Metric thread with 33 mm nominal (major) diameter and 2 mm pitch
  3. 33 mm length and 2 mm diameter
  4. 33 threads in 2 cm
Show answer & solution

Answer: (B) Metric thread with 33 mm nominal (major) diameter and 2 mm pitch

If the pitch is omitted, a coarse pitch is implied.

Question 8

What is the major (crest) diameter of a screw thread?

  1. The core diameter
  2. The pitch diameter
  3. The smallest diameter of the thread
  4. The largest diameter of the thread
Show answer & solution

Answer: (D) The largest diameter of the thread

It is also called the nominal diameter.

Question 9

What is the minor (core) diameter of an external thread?

  1. The diameter of the head
  2. The largest diameter of the thread
  3. The smallest diameter of the thread
  4. The diameter at the pitch line
Show answer & solution

Answer: (C) The smallest diameter of the thread

Stress in a bolt is calculated on the core (root) area.

Question 10

What is the pitch of a screw thread?

  1. The depth of the thread
  2. The diameter of the thread
  3. The angle of the thread
  4. The axial distance between corresponding points on adjacent threads
Show answer & solution

Answer: (D) The axial distance between corresponding points on adjacent threads

For a single-start thread, lead equals pitch.

Question 11

What is the lead of a screw?

  1. The diameter of the screw
  2. The thread depth
  3. The axial distance moved by the nut in one complete turn
  4. The thread angle
Show answer & solution

Answer: (C) The axial distance moved by the nut in one complete turn

For a double-start thread, lead = 2 × pitch.

Question 12

What is the included angle of ISO metric and Unified threads?

  1. 29°
  2. 47°
  3. 55°
  4. 60°
Show answer & solution

Answer: (D) 60°

British Standard Whitworth threads have 55°.

Question 13

What is the included angle of BSW (British Standard Whitworth) threads?

  1. 29°
  2. 55°
  3. 60°
  4. 90°
Show answer & solution

Answer: (B) 55°

Whitworth threads have rounded crests and roots.

Question 14

What is the included angle of Acme threads?

  1. 29°
  2. 45°
  3. 55°
  4. 60°
Show answer & solution

Answer: (A) 29°

Acme threads are used in lead screws and power screws.

Question 15

Which thread is used for power screws such as screw jacks because it has the highest efficiency?

  1. Square thread
  2. Whitworth thread
  3. Pipe thread
  4. V-thread
Show answer & solution

Answer: (A) Square thread

It has no radial pressure on the nut.

Question 16

Which thread is best for applications where large forces act in one direction only?

  1. Metric V-thread
  2. Buttress thread
  3. Acme thread
  4. Square thread
Show answer & solution

Answer: (B) Buttress thread

It is used in vices, gun breeches and railway carriage couplings.

Question 17

Which thread type is best suited for leak-tight pipe joints?

  1. Acme threads
  2. Square threads
  3. Tapered pipe threads (such as NPT or BSPT)
  4. Buttress threads
Show answer & solution

Answer: (C) Tapered pipe threads (such as NPT or BSPT)

The taper wedges the joint tight.

Question 18

What is a self-locking screw?

  1. A screw with a lock nut
  2. A screw with fine threads only
  3. A screw with two starts
  4. A screw in which the friction angle is greater than the helix (lead) angle, so the load cannot lower itself
Show answer & solution

Answer: (D) A screw in which the friction angle is greater than the helix (lead) angle, so the load cannot lower itself

Self-locking screws have efficiency below 50%.

Question 19

What is the maximum efficiency of a self-locking square-threaded screw?

  1. More than 75%
  2. Exactly 100%
  3. Less than 50%
  4. Exactly 90%
Show answer & solution

Answer: (C) Less than 50%

This follows from the self-locking condition.

Question 20

Why are ball (recirculating ball) screws used in vehicle steering and machine tools?

  1. They replace sliding friction with rolling friction, giving high efficiency
  2. They are cheaper than all other screws
  3. They need no maintenance at all
  4. They are self-locking
Show answer & solution

Answer: (A) They replace sliding friction with rolling friction, giving high efficiency

Balls circulate between the screw and nut.

Question 21

What is the function of a washer?

  1. To lock the nut permanently
  2. To provide a larger, smooth bearing surface under a nut or bolt head
  3. To seal the joint against fluids always
  4. To absorb all vibration
Show answer & solution

Answer: (B) To provide a larger, smooth bearing surface under a nut or bolt head

Spring washers also help resist loosening.

Question 22

What is a jam (lock) nut?

  1. A thinner nut tightened against the main nut to lock it by friction
  2. A nut with slots for a split pin
  3. A nut with a split
  4. A nut with a nylon insert
Show answer & solution

Answer: (A) A thinner nut tightened against the main nut to lock it by friction

The jam nut has the same pitch as the main nut.

Question 23

What is a castle nut?

  1. A nut with a nylon insert
  2. A nut with slots at the top through which a split (cotter) pin passes into a hole in the bolt
  3. A thin lock nut
  4. A nut with a split body
Show answer & solution

Answer: (B) A nut with slots at the top through which a split (cotter) pin passes into a hole in the bolt

It is used in automobile wheel hubs.

Question 24

What is an elastic stop nut?

  1. A nut with slots
  2. A nut with a hexagonal socket
  3. A thin lock nut
  4. A nut with a fibre or nylon insert that grips the bolt thread
Show answer & solution

Answer: (D) A nut with a fibre or nylon insert that grips the bolt thread

The insert is threaded by the bolt as the nut is screwed on.

Question 25

What is a split nut (as a locking device)?

  1. A nut cut into two halves for a lathe lead screw only
  2. A nut with slots for a pin
  3. A nut with a partial slot that is closed by tightening a screw to grip the bolt
  4. A nut with nylon insert
Show answer & solution

Answer: (C) A nut with a partial slot that is closed by tightening a screw to grip the bolt

The clamping force prevents loosening.

Question 26

What is a turnbuckle?

  1. A nut with nylon insert
  2. A rivet
  3. A coupling with right-hand thread at one end and left-hand thread at the other, used to adjust tension
  4. A bolt with two heads
Show answer & solution

Answer: (C) A coupling with right-hand thread at one end and left-hand thread at the other, used to adjust tension

Turning the body tightens or loosens both rods at once.

Question 27

If the thread on a bolt is left-handed, what thread must its nut have?

  1. Right-handed with the same pitch
  2. Left-handed with a finer pitch
  3. Any hand
  4. Left-handed with the same pitch
Show answer & solution

Answer: (D) Left-handed with the same pitch

Left-hand threads are used where rotation would loosen a right-hand nut.

Question 28

How can a bolt of uniform strength (better shock resistance) be made?

  1. By reducing the shank diameter to the core diameter of the thread, or drilling an axial hole in the shank
  2. By adding a washer
  3. By making the bolt longer only
  4. By increasing the shank diameter
Show answer & solution

Answer: (A) By reducing the shank diameter to the core diameter of the thread, or drilling an axial hole in the shank

This allows the shank to stretch more and absorb energy.

Question 29

Under shock loading, where is a bolt most likely to break?

  1. At the middle of the shank
  2. At the threaded portion
  3. At the head
  4. At the washer
Show answer & solution

Answer: (B) At the threaded portion

The thread root has the smallest area and highest stress concentration.

Question 30

Why should the shear plane of a bolt not pass through its threaded portion?

  1. Threads increase strength
  2. It makes assembly easier
  3. It reduces cost
  4. The threaded portion has a smaller area and stress raisers
Show answer & solution

Answer: (D) The threaded portion has a smaller area and stress raisers

Fitted bolts have a plain shank in the shear plane.

Question 31

Why are connecting rod bolts tightened with an initial tension greater than the external load?

  1. To make removal easy
  2. So that the resultant load on the bolt is little affected by the cyclic external load
  3. To allow the joint to open
  4. To reduce bolt size
Show answer & solution

Answer: (B) So that the resultant load on the bolt is little affected by the cyclic external load

This reduces fatigue loading on the bolt.

Question 32

On what does the resultant axial load on a pre-tightened bolt depend?

  1. Initial tension, external load and the relative stiffness of the bolt and connected parts
  2. Initial tension only
  3. External load only
  4. Bolt length only
Show answer & solution

Answer: (A) Initial tension, external load and the relative stiffness of the bolt and connected parts

A stiffer joint reduces the extra load on the bolt.

Question 33

What type of stress does tightening a nut on a bolt produce in the bolt?

  1. Pure bending
  2. Pure compression
  3. Tensile stress (with some torsional shear during tightening)
  4. No stress
Show answer & solution

Answer: (C) Tensile stress (with some torsional shear during tightening)

The clamped parts are in compression.

Question 34

What is the standard height of a hexagonal nut in terms of the nominal bolt diameter d?

  1. About 0.2d
  2. About 0.8d
  3. About 2d
  4. About 3d
Show answer & solution

Answer: (B) About 0.8d

This makes the threads in the nut about as strong as the bolt.

Question 35

For a leak-proof flanged pipe joint, what is the usual circumferential pitch of the bolts in terms of bolt hole diameter d?

  1. 100d
  2. d/2
  3. 2d
  4. 20√d to 30√d (in mm)
Show answer & solution

Answer: (D) 20√d to 30√d (in mm)

Closer bolts keep the gasket evenly compressed.

Question 36

What is the torque required to raise a load W with a square-threaded screw of mean diameter d, helix angle α and friction angle φ?

  1. W × d
  2. W tan(α + φ) × d/2
  3. W tan(α − φ) × d/2
  4. W sin α × d
Show answer & solution

Answer: (B) W tan(α + φ) × d/2

Collar friction adds extra torque.

Question 37

What is a machine screw?

  1. A large bolt with a hexagonal head
  2. A rod threaded at both ends
  3. A key
  4. A small screw slotted for a screwdriver, often used with a nut
Show answer & solution

Answer: (D) A small screw slotted for a screwdriver, often used with a nut

It is common in electrical and light assemblies.

Question 38

What is the purpose of cutting oil when threading a pipe?

  1. Cooling the die, lubricating it and helping remove chips
  2. Hardening the thread
  3. Sealing the joint
  4. Painting the pipe
Show answer & solution

Answer: (A) Cooling the die, lubricating it and helping remove chips

It also improves thread finish.

Practice these 38 questions interactively →