What is a bearing?
Show answer & solution
Answer: (D) A machine element that supports a rotating or moving part and allows relative motion with minimum friction
Bearings carry radial loads, axial loads or both.
Mechanical Engineering · Machine Design
33 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a bearing?
Answer: (D) A machine element that supports a rotating or moving part and allows relative motion with minimum friction
Bearings carry radial loads, axial loads or both.
What are the two main types of bearings?
Answer: (A) Sliding contact (journal) bearings and rolling contact (antifriction) bearings
Ball and roller bearings are rolling contact bearings.
Which bearings are known as antifriction bearings?
Answer: (B) Ball and roller bearings
Rolling contact gives low starting friction.
What is a hydrodynamic (self-acting) journal bearing?
Answer: (C) A bearing in which oil film pressure is generated by the rotation of the journal
A wedge-shaped oil film supports the load.
What is a hydrostatic bearing?
Answer: (D) A bearing in which the load is supported by oil supplied under external pressure
It can support loads even at zero speed.
What is an oilless (self-lubricating) bearing?
Answer: (B) A bearing that needs no external supply of lubricant, such as a porous sintered bronze bearing impregnated with oil
Graphite and PTFE bearings are also self-lubricating.
What is the bearing characteristic number?
Answer: (A) ZN/p, where Z is viscosity, N is speed and p is bearing pressure
It is used to judge whether a bearing operates with full-film lubrication.
What is the usual diametral clearance in a hydrodynamic bearing?
Answer: (B) About 1 micron per mm of shaft diameter (0.001d)
Clearance affects oil film thickness and heat generation.
Where should oil be supplied to a journal bearing?
Answer: (D) At the point where the load is lightest
Supplying at the loaded zone would disturb the pressure film.
How does the rated life of a ball bearing vary with load?
Answer: (C) Inversely as the cube of the load
For roller bearings, the exponent is 10/3.
What is the basic dynamic load rating of a rolling bearing?
Answer: (A) The load that 90% of a group of bearings can carry for one million revolutions
It is used to select bearings from catalogues.
What is the L10 life of a bearing?
Answer: (A) The life that 90% of a group of identical bearings will reach or exceed
It is usually expressed in millions of revolutions.
Which bearing is best suited to carry radial load in a small radial space with fluctuating loads?
Answer: (D) Needle roller bearing
Needle bearings have many slender rollers.
Which rolling bearing can carry heavy radial and axial loads together?
Answer: (C) Taper roller bearing
It is used in vehicle wheel hubs.
Which bearing allows for misalignment of the shaft?
Answer: (B) Self-aligning ball bearing
Its outer race has a spherical track.
What is a thrust bearing?
Answer: (D) A bearing designed to carry axial loads
Footstep and collar bearings are thrust bearings.
What is a babbitt metal (white metal) used for?
Answer: (B) Lining sliding bearings because it is soft, conformable and embeds dirt
It is an alloy of tin or lead with antimony and copper.
Why are bearing materials usually softer than the shaft material?
Answer: (A) So that wear occurs on the cheaper, replaceable bearing rather than on the shaft
Soft materials also embed abrasive particles.
What is viscosity index of a lubricating oil?
Answer: (C) A measure of how little its viscosity changes with temperature
A high viscosity index means more stable viscosity.
What is the flash point of a lubricant?
Answer: (B) The lowest temperature at which its vapour ignites momentarily when a flame is applied
The fire point is slightly higher.
What is boundary lubrication?
Answer: (C) Lubrication in which a very thin film exists and surfaces are partly in contact
It occurs at low speed or high load.
What is the length-to-diameter (L/D) ratio of most journal bearings?
Answer: (B) About 0.5 to 2
Short bearings run cooler; long bearings have higher load capacity.
What is a full journal bearing?
Answer: (C) A bearing in which the bush surrounds the journal completely (360°)
Partial bearings cover 120° or 180°.
What is a deep groove ball bearing suitable for?
Answer: (D) Radial loads and moderate axial loads at high speeds
It is the most widely used rolling bearing.
What is the main advantage of rolling contact bearings over sliding bearings?
Answer: (A) Low starting friction and easy lubrication and replacement
They are standardised and available from catalogues.
What is the main advantage of sliding contact bearings over rolling contact bearings?
Answer: (C) They run quietly and handle shock loads well
They are used in engine crankshafts.
What is the Sommerfeld number used for?
Answer: (C) Characterising the performance of hydrodynamic journal bearings
It is a dimensionless number combining speed, viscosity, load and clearance.
What is the Petroff equation used for?
Answer: (B) Estimating friction in a lightly loaded journal bearing
It assumes the journal runs concentric with the bearing.
What is the minimum oil film thickness in a hydrodynamic bearing?
Answer: (D) The smallest gap between journal and bearing during operation
It must exceed the surface roughness to avoid metal contact.
Why are bearings often pre-loaded?
Answer: (A) To remove internal clearance and increase stiffness and accuracy
Machine tool spindles use pre-loaded bearings.
What is grease preferred to oil for?
Answer: (A) Bearings that are hard to reach, low-speed bearings and where sealing is difficult
Grease stays in place but removes less heat.
What is the pour point of a lubricating oil?
Answer: (D) The lowest temperature at which the oil can still flow
It is important for cold climates.
What is the main purpose of a lubricant in a bearing?
Answer: (B) Reducing friction and wear, carrying away heat and protecting against corrosion
Lubricants also flush away wear particles.