Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Machine Design: Design Fundamentals

Mechanical Engineering · Machine Design

48 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is machine design?

  1. The drawing of buildings
  2. The repair of machines only
  3. The operation of machines
  4. The creation of plans for machines or parts that perform their functions safely, reliably and economically
Show answer & solution

Answer: (D) The creation of plans for machines or parts that perform their functions safely, reliably and economically

It involves selecting materials, shapes, sizes and manufacturing methods.

Question 2

What is the first step in the design of a machine element?

  1. Selling the product
  2. Identifying the need and defining the problem
  3. Manufacturing a prototype
  4. Choosing the colour
Show answer & solution

Answer: (B) Identifying the need and defining the problem

Design then moves to synthesis, analysis, material selection and detailing.

Question 3

What is factor of safety in machine design?

  1. The ratio of working stress to failure stress
  2. The ratio of load to area
  3. The ratio of failure stress (yield or ultimate) to the allowable working stress
  4. The ratio of cost to strength
Show answer & solution

Answer: (C) The ratio of failure stress (yield or ultimate) to the allowable working stress

It allows for uncertainties in loads, materials and analysis.

Question 4

For ductile materials under static loads, on which stress is the factor of safety usually based?

  1. Yield stress
  2. Breaking stress
  3. Ultimate stress
  4. Endurance limit
Show answer & solution

Answer: (A) Yield stress

Ductile parts are considered failed when they yield.

Question 5

For brittle materials under static loads, on which stress is the factor of safety usually based?

  1. Yield stress
  2. Proof stress
  3. Ultimate stress
  4. Endurance limit
Show answer & solution

Answer: (C) Ultimate stress

Brittle materials have no clear yield point.

Question 6

Which theory of failure is applied to brittle materials?

  1. Distortion energy theory
  2. Maximum principal stress theory (Rankine's theory)
  3. Maximum shear stress theory
  4. Maximum strain energy theory
Show answer & solution

Answer: (B) Maximum principal stress theory (Rankine's theory)

Cast iron parts are designed using it.

Question 7

Which theory of failure, also called Guest's or Tresca's theory, is applied to ductile materials?

  1. Maximum shear stress theory
  2. Rankine's theory
  3. Maximum principal strain theory
  4. Maximum principal stress theory
Show answer & solution

Answer: (A) Maximum shear stress theory

It gives conservative, safe results.

Question 8

Which theory of failure agrees best with test results for ductile materials?

  1. Maximum principal stress theory
  2. Maximum normal stress theory
  3. Maximum principal strain theory
  4. Distortion energy theory (von Mises–Hencky)
Show answer & solution

Answer: (D) Distortion energy theory (von Mises–Hencky)

It is widely used in modern design.

Question 9

What is stress concentration?

  1. Uniform stress throughout a part
  2. A localised increase in stress at discontinuities such as holes, notches, keyways and sudden changes of section
  3. Stress caused by temperature only
  4. Reduction of stress near holes
Show answer & solution

Answer: (B) A localised increase in stress at discontinuities such as holes, notches, keyways and sudden changes of section

It is expressed by the stress concentration factor Kt.

Question 10

What is the theoretical stress concentration factor for a small circular hole in a wide plate under tension?

  1. 1
  2. 2
  3. 3
  4. 5
Show answer & solution

Answer: (C) 3

The maximum stress at the edge of the hole is three times the nominal stress.

Question 11

How can stress concentration be reduced?

  1. By using generous fillet radii, gradual changes of section and relief grooves
  2. By using brittle materials
  3. By adding sharp corners
  4. By making holes larger at random
Show answer & solution

Answer: (A) By using generous fillet radii, gradual changes of section and relief grooves

Smooth contours allow stress to flow evenly.

Question 12

In which materials is stress concentration more serious under static loading?

  1. Equally in both
  2. Ductile materials
  3. In neither
  4. Brittle materials
Show answer & solution

Answer: (D) Brittle materials

Local yielding in ductile materials relieves peak stresses.

Question 13

Under cyclic (fatigue) loading, how serious is stress concentration for ductile and brittle materials?

  1. It is serious for both types of material
  2. It does not matter
  3. It matters only for ductile materials
  4. It matters only for brittle materials
Show answer & solution

Answer: (A) It is serious for both types of material

Fatigue cracks usually begin at stress raisers.

Question 14

What is fatigue failure?

  1. Failure under a single static load
  2. Failure of a part under repeated or fluctuating stresses, often below the yield stress
  3. Failure due to wear
  4. Failure due to corrosion only
Show answer & solution

Answer: (B) Failure of a part under repeated or fluctuating stresses, often below the yield stress

Most failures of rotating machine parts are fatigue failures.

Question 15

If a material fails below its yield point under repeated loading, what is the likely cause?

  1. Creep at room temperature
  2. Buckling
  3. Static overload
  4. Fatigue
Show answer & solution

Answer: (D) Fatigue

Repeated loading starts and grows small cracks.

Question 16

What is the endurance limit?

  1. The ultimate tensile stress
  2. The yield stress
  3. The maximum completely reversed stress a material can withstand for an infinite number of cycles without failure
  4. The stress at fracture
Show answer & solution

Answer: (C) The maximum completely reversed stress a material can withstand for an infinite number of cycles without failure

It is found using a rotating beam test.

Question 17

What type of loading is used to find the endurance limit in a rotating beam test?

  1. Static loading
  2. Impact loading
  3. Constant tensile loading
  4. Completely reversed loading
Show answer & solution

Answer: (D) Completely reversed loading

Each point on the surface goes from tension to compression every revolution.

Question 18

How does surface finish affect the endurance limit?

  1. Rough surfaces increase it
  2. A polished surface gives a higher endurance limit than a rough surface
  3. Surface finish has no effect
  4. Only colour matters
Show answer & solution

Answer: (B) A polished surface gives a higher endurance limit than a rough surface

Surface scratches act as starting points for cracks.

Question 19

Which process improves fatigue life by inducing compressive residual stresses on the surface?

  1. Shot peening
  2. Decarburisation
  3. Electroplating
  4. Rough machining
Show answer & solution

Answer: (A) Shot peening

Cold rolling of threads and fillets has a similar effect.

Question 20

Which of the following reduces the fatigue strength of steel?

  1. Cold rolling
  2. Shot peening
  3. Surface decarburisation
  4. Polishing
Show answer & solution

Answer: (C) Surface decarburisation

Loss of carbon weakens the surface layer where cracks start.

Question 21

Why is electroplating to rebuild worn parts that carry repeated loads considered hazardous?

  1. It has no effect
  2. It increases fatigue strength too much
  3. Plating can introduce tensile residual stresses and hydrogen embrittlement, reducing fatigue strength
  4. It makes parts heavier
Show answer & solution

Answer: (C) Plating can introduce tensile residual stresses and hydrogen embrittlement, reducing fatigue strength

Such parts are better rebuilt by other methods.

Question 22

What is coaxing in fatigue?

  1. Raising the fatigue limit by under-stressing and then gradually increasing the stress level
  2. Coating the surface
  3. Annealing the part
  4. Reducing hardness
Show answer & solution

Answer: (A) Raising the fatigue limit by under-stressing and then gradually increasing the stress level

It is mainly observed in some steels.

Question 23

What are residual stresses?

  1. Stresses only under load
  2. Stresses that remain in a part without any external load, due to manufacturing processes
  3. Stresses that disappear after loading
  4. Stresses due to gravity only
Show answer & solution

Answer: (B) Stresses that remain in a part without any external load, due to manufacturing processes

Welding and heat treatment often cause residual stresses.

Question 24

Which diagram is used to design parts under fluctuating stresses with mean and alternating components?

  1. Mollier chart
  2. Mohr's circle
  3. Moody chart
  4. Goodman (or Soderberg) diagram
Show answer & solution

Answer: (D) Goodman (or Soderberg) diagram

The Soderberg line uses yield strength and is more conservative.

Question 25

What is creep?

  1. Slow, permanent deformation of a material under constant stress over time, especially at high temperature
  2. Fatigue failure
  3. Sudden fracture
  4. Elastic deformation
Show answer & solution

Answer: (A) Slow, permanent deformation of a material under constant stress over time, especially at high temperature

It is important in boilers and turbine blades.

Question 26

What does "hot short" mean for a metal?

  1. It is brittle when cold
  2. It is ductile at high temperature
  3. It is brittle when hot
  4. It is soft at room temperature
Show answer & solution

Answer: (C) It is brittle when hot

Sulphur in steel can cause hot shortness.

Question 27

What type of fracture surface do ductile materials usually show?

  1. Glassy
  2. Fibrous
  3. Granular
  4. Crystalline and flat
Show answer & solution

Answer: (B) Fibrous

Brittle materials show a bright, granular fracture.

Question 28

Why is cast iron often used for machine beds and frames?

  1. It is the strongest material in tension
  2. It is very ductile
  3. It is very light
  4. It has good damping, compressive strength and rigidity for equal load-carrying ability, and is easy to cast
Show answer & solution

Answer: (D) It has good damping, compressive strength and rigidity for equal load-carrying ability, and is easy to cast

Lathe beds are usually made of grey cast iron.

Question 29

Which hardness test can be used to estimate the tensile strength of steel?

  1. Brinell hardness test
  2. Mohs test
  3. Shore scleroscope only
  4. None
Show answer & solution

Answer: (A) Brinell hardness test

Tensile strength in MPa is roughly 3.45 × BHN for steels.

Question 30

What is the angle of the diamond pyramid indenter used in the Vickers hardness test?

  1. 90°
  2. 120°
  3. 136°
  4. 150°
Show answer & solution

Answer: (C) 136°

The load is divided by the surface area of the indentation.

Question 31

What is the notch angle of a standard Izod impact test specimen?

  1. 30°
  2. 45°
  3. 60°
  4. 90°
Show answer & solution

Answer: (B) 45°

The specimen is held vertically as a cantilever.

Question 32

How does the impact strength of most steels change at very low temperatures?

  1. It stays the same
  2. It increases markedly
  3. It becomes infinite
  4. It decreases markedly
Show answer & solution

Answer: (D) It decreases markedly

Steel undergoes a ductile-to-brittle transition at low temperature.

Question 33

What is tolerance?

  1. The clearance between parts
  2. The permissible variation in a dimension, equal to the difference between the upper and lower limits
  3. The basic size
  4. The surface finish
Show answer & solution

Answer: (B) The permissible variation in a dimension, equal to the difference between the upper and lower limits

Tighter tolerances increase manufacturing cost.

Question 34

What is a basic hole in the hole-basis system of fits?

  1. A hole with zero tolerance
  2. A hole of any size
  3. A hole whose lower deviation is zero
  4. A hole whose upper deviation is zero
Show answer & solution

Answer: (C) A hole whose lower deviation is zero

Different fits are obtained by changing the shaft size.

Question 35

What is a basic shaft in the shaft-basis system of fits?

  1. A shaft whose upper deviation is zero
  2. A shaft with zero tolerance
  3. A shaft whose lower deviation is zero
  4. A shaft of any size
Show answer & solution

Answer: (A) A shaft whose upper deviation is zero

The hole size is varied to obtain different fits.

Question 36

Why is the hole-basis system generally preferred?

  1. Holes have no tolerance
  2. It needs more tools
  3. Shafts are harder to machine
  4. Holes are made with standard tools such as drills and reamers, while shafts are easier to machine to any size
Show answer & solution

Answer: (D) Holes are made with standard tools such as drills and reamers, while shafts are easier to machine to any size

It reduces the number of special tools needed.

Question 37

What is a clearance fit?

  1. A permanent welded joint
  2. A fit in which the shaft is always larger than the hole
  3. A fit in which the shaft is always smaller than the hole
  4. A fit that may have clearance or interference
Show answer & solution

Answer: (C) A fit in which the shaft is always smaller than the hole

Running fits for bearings are clearance fits.

Question 38

What is an interference fit?

  1. A fit with clearance
  2. A fit with no tolerance
  3. A loose sliding fit
  4. A fit in which the shaft is always larger than the hole, requiring force or heating to assemble
Show answer & solution

Answer: (D) A fit in which the shaft is always larger than the hole, requiring force or heating to assemble

It is used for parts that must not move relative to each other.

Question 39

What is a transition fit?

  1. A fit that may give either a small clearance or a small interference
  2. A fit with large clearance
  3. A fit with large interference
  4. A welded joint
Show answer & solution

Answer: (A) A fit that may give either a small clearance or a small interference

It is used for locating fits.

Question 40

How many standard tolerance grades (IT grades) are specified in the ISO system of limits and fits?

  1. 12
  2. 16
  3. 20
  4. 25
Show answer & solution

Answer: (C) 20

They range from IT01 and IT0 to IT18.

Question 41

What is standardisation in machine design?

  1. Making every part unique
  2. Using standard sizes, materials and specifications for parts
  3. Using only one material
  4. Avoiding all specifications
Show answer & solution

Answer: (B) Using standard sizes, materials and specifications for parts

It allows interchangeability and reduces cost.

Question 42

What does interchangeability mean?

  1. Parts are always made by the same worker
  2. Parts made to specified limits can replace each other without fitting
  3. Parts can never be replaced
  4. Each part must be hand-fitted
Show answer & solution

Answer: (B) Parts made to specified limits can replace each other without fitting

It is essential for mass production.

Question 43

What is ergonomics in machine design?

  1. Designing machines to suit the comfort, safety and efficiency of human operators
  2. Designing for minimum weight
  3. Designing for colour only
  4. Designing for corrosion
Show answer & solution

Answer: (A) Designing machines to suit the comfort, safety and efficiency of human operators

Control positions and forces are chosen to suit the human body.

Question 44

What is the endurance limit of steel in shear compared with its endurance limit in bending?

  1. Equal
  2. About 0.55–0.58 times
  3. About 1.5 times
  4. About 0.1 times
Show answer & solution

Answer: (B) About 0.55–0.58 times

Distortion energy theory gives a ratio of 0.577.

Question 45

What is the endurance limit of a polished steel specimen compared with its ultimate tensile strength?

  1. About half the ultimate tensile strength
  2. About twice
  3. About one-tenth
  4. Equal to the ultimate tensile strength
Show answer & solution

Answer: (A) About half the ultimate tensile strength

Factors for size, surface and reliability then reduce it for real parts.

Question 46

What is the effect of cold working on the fatigue strength of steel?

  1. It has no effect
  2. It makes steel brittle at all temperatures
  3. It always reduces fatigue strength
  4. It generally increases fatigue strength
Show answer & solution

Answer: (D) It generally increases fatigue strength

Surface cold rolling is used on threads and fillets.

Question 47

What is the purpose of brittle coating in experimental stress analysis?

  1. To test brittleness
  2. To protect against corrosion
  3. To show regions of high strain by cracking of the coating
  4. To make the surface smooth
Show answer & solution

Answer: (C) To show regions of high strain by cracking of the coating

Photoelasticity and strain gauges are other methods.

Question 48

What is reliability in machine design?

  1. The colour of a part
  2. The weight of a part
  3. The cost of a part
  4. The probability that a part will perform its function without failure for a specified time
Show answer & solution

Answer: (D) The probability that a part will perform its function without failure for a specified time

Higher reliability needs larger safety factors or better materials.

Practice these 48 questions interactively →