Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Machine Design: Gears, Drives and Brakes

Mechanical Engineering · Machine Design

33 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

In a V-belt drive, where does the belt make contact with the pulley?

  1. On the sides of the groove only
  2. At the bottom of the groove
  3. At both sides and bottom
  4. At the top only
Show answer & solution

Answer: (A) On the sides of the groove only

Contact with the bottom would reduce the wedging action.

Question 2

What can cause belt slip?

  1. A clean belt
  2. A large angle of contact
  3. Correct tension
  4. Heavy load, loose belt or a small driving pulley
Show answer & solution

Answer: (D) Heavy load, loose belt or a small driving pulley

Slip reduces efficiency and causes wear.

Question 3

In a regular (cross) lay wire rope, how are the wires and strands twisted?

  1. Adjacent strands are twisted in opposite directions
  2. The wires are twisted in the opposite direction to the strands
  3. Wires are not twisted
  4. Wires and strands are twisted the same way
Show answer & solution

Answer: (B) The wires are twisted in the opposite direction to the strands

Regular lay ropes resist untwisting and crushing.

Question 4

In a Lang's lay wire rope, how are the wires and strands twisted?

  1. Wires are straight
  2. In opposite directions
  3. Strands are straight
  4. In the same direction
Show answer & solution

Answer: (D) In the same direction

Lang's lay ropes are more flexible and resist wear better.

Question 5

Why does a wire rope have a core?

  1. To conduct electricity
  2. To reduce flexibility
  3. To support the strands and keep their shape, and to hold lubricant
  4. To increase weight
Show answer & solution

Answer: (C) To support the strands and keep their shape, and to hold lubricant

Cores may be of fibre or steel.

Question 6

What is the purpose of a gearbox?

  1. To obtain different speeds and torques from a constant input speed
  2. To produce torque
  3. To reduce vibration only
  4. To store energy
Show answer & solution

Answer: (A) To obtain different speeds and torques from a constant input speed

Vehicles use gearboxes to match engine speed to road speed.

Question 7

What is the Lewis equation used for?

  1. Calculating bearing life
  2. Calculating spring stiffness
  3. Calculating the bending strength of gear teeth
  4. Calculating belt tension
Show answer & solution

Answer: (C) Calculating the bending strength of gear teeth

It treats each tooth as a cantilever beam.

Question 8

What is the Buckingham equation used for in gear design?

  1. Calculating dynamic load on gear teeth
  2. Calculating bearing clearance
  3. Calculating shaft diameter
  4. Calculating key length
Show answer & solution

Answer: (A) Calculating dynamic load on gear teeth

Dynamic loads arise from tooth errors and speed.

Question 9

Why is the pinion usually made of a stronger material than the gear?

  1. The gear runs faster
  2. The pinion's teeth are weaker in form and engage more often
  3. The pinion is larger
  4. It is cheaper
Show answer & solution

Answer: (B) The pinion's teeth are weaker in form and engage more often

This balances the strength of the pair.

Question 10

Which pipe joint is suitable for long steam pipelines subject to large temperature changes?

  1. Rigid flanged joint without allowance
  2. Threaded joint
  3. Bell and spigot joint
  4. Expansion joint
Show answer & solution

Answer: (D) Expansion joint

It allows the pipe to expand and contract.

Question 11

How can thermal expansion of small tubing be accommodated?

  1. By honing the tube
  2. By crimping the tube
  3. By providing bends or loops
  4. By making it straight and rigid
Show answer & solution

Answer: (C) By providing bends or loops

Bends flex as the tube expands.

Question 12

What are the advantages of tubes over pipes?

  1. Tubes cannot be bent
  2. Tubes are lighter, easier to bend and handle, and have smoother inside walls
  3. Tubes are heavier
  4. Tubes are always thicker
Show answer & solution

Answer: (B) Tubes are lighter, easier to bend and handle, and have smoother inside walls

Tubes are specified by outside diameter and wall thickness.

Question 13

What type of solder is used for brazing?

  1. Silver-based (hard) solder
  2. Plastic
  3. Lead–tin soft solder
  4. Zinc only
Show answer & solution

Answer: (A) Silver-based (hard) solder

Brazing gives stronger joints than soft soldering.

Question 14

What is the thickness of a thin cylindrical pressure vessel required for internal pressure p, diameter d and allowable stress σ?

  1. t = pd/σ
  2. t = pd/4σ
  3. t = 2pd/σ
  4. t = pd/2σ
Show answer & solution

Answer: (D) t = pd/2σ

Joint efficiency is included for welded or riveted shells.

Question 15

Why are pressure vessel heads often made hemispherical or ellipsoidal?

  1. They carry pressure with lower stress than flat heads
  2. They are lighter only because of colour
  3. They need no welding
  4. They are cheaper than flat plates
Show answer & solution

Answer: (A) They carry pressure with lower stress than flat heads

A hemispherical head needs only half the thickness of the cylindrical shell.

Question 16

Why are friction clutches designed using the uniform wear theory?

  1. It gives higher torque
  2. It ignores friction
  3. It applies only to new clutches
  4. It gives a lower, safer estimate of torque capacity after initial wear
Show answer & solution

Answer: (D) It gives a lower, safer estimate of torque capacity after initial wear

Uniform pressure theory applies to new clutches.

Question 17

What is the most common material for brake linings in modern vehicles?

  1. Glass
  2. Non-asbestos organic or semi-metallic friction material
  3. Pure copper
  4. Rubber only
Show answer & solution

Answer: (B) Non-asbestos organic or semi-metallic friction material

Asbestos linings have been phased out for health reasons.

Question 18

What is the main design consideration for brakes apart from torque capacity?

  1. Noise only
  2. Weight only
  3. Heat dissipation
  4. Colour
Show answer & solution

Answer: (C) Heat dissipation

The kinetic energy absorbed is converted into heat.

Question 19

What is the main advantage of a chain drive over a belt drive in power transmission?

  1. It gives a positive drive without slip and can transmit more power in a smaller space
  2. It needs no lubrication
  3. It can connect intersecting shafts
  4. It is completely silent
Show answer & solution

Answer: (A) It gives a positive drive without slip and can transmit more power in a smaller space

Roller chains are standardised by pitch.

Question 20

What is the chordal (polygonal) effect in chain drives?

  1. Stretching of the chain
  2. Variation in chain speed because the chain wraps the sprocket as a polygon
  3. Breaking of rollers
  4. Slipping of the chain
Show answer & solution

Answer: (B) Variation in chain speed because the chain wraps the sprocket as a polygon

More sprocket teeth reduce the chordal effect.

Question 21

Why should a chain drive have an odd number of sprocket teeth and an even number of chain links?

  1. To increase speed
  2. To reduce cost
  3. To distribute wear evenly over the teeth and links
  4. To make the chain lighter
Show answer & solution

Answer: (C) To distribute wear evenly over the teeth and links

The same link then meets a different tooth each time.

Question 22

What is the face width of spur gears usually taken as in terms of module m?

  1. Half the module
  2. About 100 times the module
  3. Equal to the module
  4. About 10 times the module
Show answer & solution

Answer: (D) About 10 times the module

A range of 9.5m to 12.5m is common.

Question 23

What is the main cause of pitting in gear teeth?

  1. Bending fatigue at the root
  2. Corrosion only
  3. Poor colour
  4. Surface fatigue from repeated high contact stresses
Show answer & solution

Answer: (D) Surface fatigue from repeated high contact stresses

It is controlled by limiting contact (Hertz) stress.

Question 24

What is scoring in gears?

  1. Welding and tearing of tooth surfaces due to breakdown of the lubricant film
  2. Normal wear
  3. Bending failure of teeth
  4. Pitting due to fatigue
Show answer & solution

Answer: (A) Welding and tearing of tooth surfaces due to breakdown of the lubricant film

Proper lubricants and cooling prevent scoring.

Question 25

What is the virtual (formative) number of teeth used for in helical gear design?

  1. Calculating weight
  2. Calculating speed ratio
  3. Calculating tooth strength using spur gear formulas
  4. Calculating centre distance only
Show answer & solution

Answer: (C) Calculating tooth strength using spur gear formulas

Tv = T/cos³ψ, where ψ is the helix angle.

Question 26

Why are worm gears often made with a steel worm and a phosphor bronze wheel?

  1. Both must be very hard
  2. The combination gives low friction and good wear resistance
  3. Bronze is cheaper than steel
  4. Steel cannot be used for wheels
Show answer & solution

Answer: (B) The combination gives low friction and good wear resistance

There is a lot of sliding in worm gears.

Question 27

What is a flywheel designed to do in machine design?

  1. Increase mean speed
  2. Transmit power between shafts
  3. Store kinetic energy and reduce speed fluctuations
  4. Absorb heat
Show answer & solution

Answer: (C) Store kinetic energy and reduce speed fluctuations

Its size depends on the fluctuation of energy and permissible speed variation.

Question 28

Which type of stress is critical in the rim of a rotating flywheel?

  1. Compressive stress
  2. Torsional stress only
  3. No stress
  4. Hoop (tensile) stress due to centrifugal force
Show answer & solution

Answer: (D) Hoop (tensile) stress due to centrifugal force

σ = ρv², so rim speed must be limited.

Question 29

What is a gasket used for in flanged joints?

  1. Increasing bolt strength
  2. Sealing the joint against leakage of fluid
  3. Locking nuts
  4. Reducing weight
Show answer & solution

Answer: (B) Sealing the joint against leakage of fluid

Gaskets are made of rubber, fibre, metal or composites.

Question 30

What is the purpose of an O-ring?

  1. Sealing static or moving joints against fluid leakage
  2. Supporting a shaft
  3. Locking a nut
  4. Transmitting torque
Show answer & solution

Answer: (A) Sealing static or moving joints against fluid leakage

It is compressed in a groove to form a seal.

Question 31

What is a mechanical seal used for in pumps?

  1. Supporting the impeller
  2. Preventing leakage of fluid where a rotating shaft passes through the casing
  3. Reducing speed
  4. Joining pipes
Show answer & solution

Answer: (B) Preventing leakage of fluid where a rotating shaft passes through the casing

It replaces gland packing in many pumps.

Question 32

What is the purpose of a gland and packing?

  1. Sealing a moving rod or shaft passing through a housing
  2. Joining pipes permanently
  3. Locking a nut
  4. Supporting a bearing
Show answer & solution

Answer: (A) Sealing a moving rod or shaft passing through a housing

The packing is compressed by tightening the gland.

Question 33

What is the main reason for using a fluid (hydraulic) coupling in vehicles and conveyors?

  1. To lock the shafts rigidly
  2. To reduce weight
  3. To allow smooth starting and absorb shock loads
  4. To increase speed
Show answer & solution

Answer: (C) To allow smooth starting and absorb shock loads

Power is transmitted through oil.

Practice these 33 questions interactively →