Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Machine Design: Joints and Keys

Mechanical Engineering · Machine Design

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which of the following is a permanent fastening?

  1. Cotter
  2. Bolt
  3. Rivet
  4. Key
Show answer & solution

Answer: (C) Rivet

Welds are also permanent joints.

Question 2

How are rivets usually specified?

  1. By their nominal shank diameter
  2. By the head diameter
  3. By their weight
  4. By the plate thickness
Show answer & solution

Answer: (A) By their nominal shank diameter

The length is chosen to suit the plates being joined.

Question 3

What is Unwin's formula for rivet diameter d in terms of plate thickness t (both in mm)?

  1. d = t
  2. d = t²
  3. d = 6√t
  4. d = 2t
Show answer & solution

Answer: (C) d = 6√t

It is used for plates thicker than about 8 mm.

Question 4

What is the minimum margin (distance from the rivet hole centre to the plate edge) to avoid tearing at the edge?

  1. Equal to the plate thickness
  2. 5 times the rivet diameter
  3. 0.5 times the rivet diameter
  4. 1.5 times the rivet diameter
Show answer & solution

Answer: (D) 1.5 times the rivet diameter

This prevents shear failure of the plate edge.

Question 5

If the tearing efficiency of a riveted joint is 75%, what is the ratio of rivet diameter to pitch?

  1. 0.25
  2. 0.5
  3. 0.6
  4. 0.75
Show answer & solution

Answer: (A) 0.25

Tearing efficiency = (p − d)/p = 1 − d/p.

Question 6

What are fullering and caulking?

  1. Methods of welding
  2. Methods of making riveted joints of boilers and tanks leak-proof by hammering the plate edges
  3. Methods of cutting threads
  4. Methods of heat treatment
Show answer & solution

Answer: (B) Methods of making riveted joints of boilers and tanks leak-proof by hammering the plate edges

Plate edges are bevelled to about 80° for this purpose.

Question 7

Why are aircraft bodies traditionally fabricated by riveting rather than welding?

  1. Aluminium alloys used in aircraft lose strength when welded, and riveted joints resist crack growth
  2. Welding is impossible
  3. Rivets are heavier
  4. Riveting is faster in all cases
Show answer & solution

Answer: (A) Aluminium alloys used in aircraft lose strength when welded, and riveted joints resist crack growth

Modern aircraft also use adhesive bonding.

Question 8

What type of strength is considered in designing a transverse fillet weld?

  1. Shear strength only
  2. Tensile strength
  3. Torsional strength
  4. Bending strength only
Show answer & solution

Answer: (B) Tensile strength

Parallel fillet welds are designed for shear.

Question 9

What is the throat thickness of a fillet weld of leg size s?

  1. s
  2. 0.5s
  3. 1.414s
  4. 0.707s
Show answer & solution

Answer: (D) 0.707s

Weld stress is calculated on the throat area.

Question 10

Why is a backing ring used inside a pipe joint?

  1. To seal a threaded joint
  2. To make a socket weld
  3. To ensure full penetration when making a butt weld
  4. To make a fillet weld
Show answer & solution

Answer: (C) To ensure full penetration when making a butt weld

It prevents weld metal from running inside the pipe.

Question 11

What is a cotter joint used for?

  1. Joining plates permanently
  2. Connecting intersecting shafts
  3. Transmitting torque between shafts
  4. Connecting two rods carrying axial (tensile or compressive) loads, such as a piston rod to a cross-head
Show answer & solution

Answer: (D) Connecting two rods carrying axial (tensile or compressive) loads, such as a piston rod to a cross-head

A tapered cotter passes through slots in both rods.

Question 12

On how many sides is the taper usually provided on a cotter?

  1. One side only
  2. Both sides
  3. No sides
  4. Three sides
Show answer & solution

Answer: (A) One side only

The taper allows the cotter to be driven in and tightened.

Question 13

What is a gib and cotter joint used for?

  1. Joining two plates
  2. Joining the strap end of a connecting rod in steam engines
  3. Joining pipes
  4. Joining intersecting shafts
Show answer & solution

Answer: (B) Joining the strap end of a connecting rod in steam engines

The gib prevents the strap from opening out.

Question 14

What is a knuckle joint used for?

  1. Joining plates
  2. Transmitting torque
  3. Connecting two rods under tension where some angular movement is needed, such as a valve rod to an eccentric rod
  4. Joining pipes
Show answer & solution

Answer: (C) Connecting two rods under tension where some angular movement is needed, such as a valve rod to an eccentric rod

A pin passes through the eye and fork of the two rods.

Question 15

What is a key?

  1. A type of bearing
  2. A type of bolt
  3. A machine element inserted between a shaft and hub to transmit torque and prevent relative rotation
  4. A type of spring
Show answer & solution

Answer: (C) A machine element inserted between a shaft and hub to transmit torque and prevent relative rotation

Keys are usually made of mild steel.

Question 16

What is a Woodruff key?

  1. A key cut from a segment of a circular disc that can tilt in a recess in the shaft
  2. A key that slides in a long keyway
  3. A key with a hollow face
  4. A taper key with a head
Show answer & solution

Answer: (A) A key cut from a segment of a circular disc that can tilt in a recess in the shaft

It is used in machine tools and automobiles on tapered shafts.

Question 17

What is a flat saddle key?

  1. A key fixed in the shaft keyway
  2. A key with a head
  3. A disc-shaped key
  4. A taper key that fits in a keyway in the hub and is flat on the shaft
Show answer & solution

Answer: (D) A taper key that fits in a keyway in the hub and is flat on the shaft

It relies on friction and suits light loads.

Question 18

What is a hollow saddle key?

  1. A key with a gib head
  2. A taper key with its underside curved to fit the shaft, holding only by friction
  3. A Woodruff key
  4. A key with a flat face
Show answer & solution

Answer: (B) A taper key with its underside curved to fit the shaft, holding only by friction

No keyway is cut in the shaft.

Question 19

What is a feather key?

  1. A saddle key
  2. A taper key with a head
  3. A key fixed to the shaft or hub that allows the hub to slide axially
  4. A disc key
Show answer & solution

Answer: (C) A key fixed to the shaft or hub that allows the hub to slide axially

It is used in gearboxes for sliding gears.

Question 20

What is a gib-head key?

  1. A splined key
  2. A taper sunk key with a head that allows easy removal
  3. A disc key
  4. A saddle key
Show answer & solution

Answer: (B) A taper sunk key with a head that allows easy removal

The head is struck to drive the key out.

Question 21

What is a splined shaft?

  1. A tapered shaft
  2. A shaft with one key
  3. A hollow shaft
  4. A shaft with several integral keys (splines) machined on it
Show answer & solution

Answer: (D) A shaft with several integral keys (splines) machined on it

It is used in gearboxes and automobile drive shafts.

Question 22

What stresses are considered in designing a sunk key?

  1. Shear and crushing (bearing) stresses
  2. Tensile stress only
  3. Bending stress only
  4. Torsional stress only
Show answer & solution

Answer: (A) Shear and crushing (bearing) stresses

The key must resist both failure modes.

Question 23

What is the usual length of a key in relation to shaft diameter?

  1. About 1.5 times the shaft diameter
  2. Five times the diameter
  3. Equal to the hub width only
  4. Equal to one-tenth of the diameter
Show answer & solution

Answer: (A) About 1.5 times the shaft diameter

This makes the key as strong as the shaft in torsion.

Question 24

What is a rigid flange coupling used for?

  1. Connecting intersecting shafts
  2. Connecting misaligned shafts
  3. Connecting parallel offset shafts
  4. Connecting two shafts that are accurately aligned
Show answer & solution

Answer: (D) Connecting two shafts that are accurately aligned

It cannot absorb shocks or misalignment.

Question 25

What is a bushed-pin flexible coupling used for?

  1. Connecting intersecting shafts
  2. Connecting shafts with slight misalignment and absorbing shocks
  3. Permanent welding of shafts
  4. Connecting parallel shafts at large distance
Show answer & solution

Answer: (B) Connecting shafts with slight misalignment and absorbing shocks

Rubber bushes on the pins absorb shock.

Question 26

What is a muff (sleeve) coupling?

  1. A fluid coupling
  2. A universal joint
  3. A hollow cylinder fitted over the ends of two shafts and keyed to them
  4. A flexible coupling
Show answer & solution

Answer: (C) A hollow cylinder fitted over the ends of two shafts and keyed to them

It is simple but must be slid along the shaft to dismantle.

Question 27

What are the main modes of failure of a riveted joint?

  1. Fatigue of rivet heads only
  2. Corrosion only
  3. Tearing of the plate, shearing of rivets and crushing of rivets or plates
  4. Buckling of rivets only
Show answer & solution

Answer: (C) Tearing of the plate, shearing of rivets and crushing of rivets or plates

The joint strength is the least of these values.

Question 28

What is a lap joint?

  1. A cotter joint
  2. A joint in which plates are placed edge to edge with cover plates
  3. A threaded joint
  4. A joint in which one plate overlaps the other and they are riveted or welded together
Show answer & solution

Answer: (D) A joint in which one plate overlaps the other and they are riveted or welded together

Lap joints introduce some bending because of eccentric loading.

Question 29

What is a butt joint?

  1. A joint with overlapping plates
  2. A joint in which plates are placed edge to edge and joined with one or two cover (strap) plates
  3. A pinned joint
  4. A threaded joint
Show answer & solution

Answer: (B) A joint in which plates are placed edge to edge and joined with one or two cover (strap) plates

Double strap butt joints are stronger.

Question 30

What is the efficiency of a riveted joint?

  1. The ratio of the least strength of the joint to the strength of the unpunched plate
  2. The ratio of load to area
  3. The ratio of plate thickness to rivet diameter
  4. The ratio of rivet diameter to pitch
Show answer & solution

Answer: (A) The ratio of the least strength of the joint to the strength of the unpunched plate

Diamond riveted butt joints have high efficiency.

Question 31

What is the main advantage of welded joints over riveted joints?

  1. They can be dismantled easily
  2. They have no residual stresses
  3. They are lighter, stronger and leak-tight, and need no drilling
  4. They need no skilled labour
Show answer & solution

Answer: (C) They are lighter, stronger and leak-tight, and need no drilling

Welded joints are now common in boilers and structures.

Question 32

What is the main disadvantage of welded joints?

  1. They are always weaker
  2. They are heavier
  3. They may have residual stresses and distortion, and inspection is harder
  4. They cannot be made leak-proof
Show answer & solution

Answer: (C) They may have residual stresses and distortion, and inspection is harder

Heat treatment can relieve residual stresses.

Question 33

What is a parallel fillet weld designed for?

  1. Bending stress only
  2. Shear stress
  3. Compressive stress only
  4. Tensile stress only
Show answer & solution

Answer: (B) Shear stress

The weld runs parallel to the direction of load.

Question 34

What is the strength of a double parallel fillet weld of leg size s and length l with allowable shear stress τ?

  1. s l τ
  2. 2 s l τ
  3. 0.707 s l τ
  4. 1.414 s l τ
Show answer & solution

Answer: (D) 1.414 s l τ

Each weld carries 0.707 s l τ.

Question 35

What is the main function of a cotter in a cotter joint?

  1. To transmit axial load between the rods, acting in double shear
  2. To support bearings
  3. To seal the joint
  4. To transmit torque
Show answer & solution

Answer: (A) To transmit axial load between the rods, acting in double shear

The cotter is a flat wedge-shaped piece.

Question 36

What is the usual taper of a cotter?

  1. No taper
  2. About 1 in 24 to 1 in 48
  3. About 1 in 5
  4. About 1 in 2
Show answer & solution

Answer: (B) About 1 in 24 to 1 in 48

A small taper prevents the cotter from slipping out.

Question 37

What is a key used together with a pulley or gear on a shaft designed to be?

  1. Made of cast iron
  2. Stronger than the shaft
  3. Much harder than the hub
  4. Weaker than the shaft so it fails first and protects the shaft
Show answer & solution

Answer: (D) Weaker than the shaft so it fails first and protects the shaft

Keys are cheap and easy to replace.

Question 38

What is the main advantage of a splined connection over a single key?

  1. It transmits greater torque and allows axial sliding with better centring
  2. It is weaker
  3. It needs no machining
  4. It is cheaper
Show answer & solution

Answer: (A) It transmits greater torque and allows axial sliding with better centring

Splines are used in gearboxes and propeller shafts.

Question 39

What is an Oldham's coupling used for?

  1. Connecting shafts at right angles
  2. Connecting coaxial shafts rigidly
  3. Connecting two parallel shafts with a small lateral offset
  4. Connecting intersecting shafts
Show answer & solution

Answer: (C) Connecting two parallel shafts with a small lateral offset

The middle disc slides in slots on both flanges.

Practice these 39 questions interactively →