Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Utilisation & Electrical Installation: Illumination

Electrical Engineering · Utilisation & Electrical Installation

28 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the SI unit of luminous flux?

  1. Watt
  2. Candela
  3. Lux
  4. Lumen
Show answer & solution

Answer: (D) Lumen

Luminous flux is the total light output of a source.

Question 2

What is the SI unit of illuminance?

  1. Nit
  2. Lux
  3. Candela
  4. Lumen
Show answer & solution

Answer: (B) Lux

One lux equals one lumen per square metre.

Question 3

What is the SI unit of luminous intensity?

  1. Lumen
  2. Lux
  3. Candela
  4. Watt per steradian only
Show answer & solution

Answer: (C) Candela

It is one of the seven SI base units.

Question 4

What is luminous efficacy of a lamp?

  1. The light output in lumens per watt of electrical input
  2. The lamp voltage
  3. The life of the lamp
  4. The colour of light
Show answer & solution

Answer: (A) The light output in lumens per watt of electrical input

Higher efficacy means more light for less energy.

Question 5

Which lamp type has the highest luminous efficacy among these?

  1. Incandescent lamp
  2. Kerosene lamp
  3. LED lamp
  4. Halogen lamp
Show answer & solution

Answer: (C) LED lamp

LEDs commonly exceed 100 lm/W, against about 12–15 lm/W for incandescent lamps.

Question 6

What does the inverse square law of illumination state?

  1. Illuminance is independent of distance
  2. Illuminance from a point source varies inversely with the square of the distance
  3. Illuminance increases with distance
  4. Illuminance varies with the cube of distance
Show answer & solution

Answer: (B) Illuminance from a point source varies inversely with the square of the distance

E = I/d² for light falling normally on a surface.

Question 7

What is the illuminance on a surface 2 m directly below a lamp of 100 cd?

  1. 12.5 lux
  2. 25 lux
  3. 50 lux
  4. 200 lux
Show answer & solution

Answer: (B) 25 lux

E = 100/2² = 25 lux.

Question 8

What does Lambert's cosine law of illumination state?

  1. Illuminance on a surface is proportional to the cosine of the angle between the light ray and the normal
  2. Illuminance doubles at 90°
  3. Illuminance is proportional to the sine of the angle
  4. Illuminance is independent of angle
Show answer & solution

Answer: (A) Illuminance on a surface is proportional to the cosine of the angle between the light ray and the normal

E = I cos θ/d².

Question 9

What is luminance?

  1. The total light output
  2. The colour of light
  3. The light falling on a surface
  4. The luminous intensity per unit projected area of a surface, in cd/m²
Show answer & solution

Answer: (D) The luminous intensity per unit projected area of a surface, in cd/m²

Luminance determines how bright a surface appears.

Question 10

Which formula is used in the lumen method to find the number of luminaires needed?

  1. N = E/A
  2. N = UF × MF/E
  3. N = (E × A)/(F × UF × MF)
  4. N = F × A/E
Show answer & solution

Answer: (C) N = (E × A)/(F × UF × MF)

E is required illuminance, A area, F lumens per lamp, UF utilisation factor and MF maintenance factor.

Question 11

How many lamps of 3,000 lm each are needed to give 300 lux over 50 m² with UF = 0.6 and MF = 0.8?

  1. 5
  2. 8
  3. 11
  4. 15
Show answer & solution

Answer: (C) 11

N = (300 × 50)/(3,000 × 0.48) ≈ 10.4, so 11 lamps.

Question 12

What does the utilisation factor in lighting design account for?

  1. The fraction of lamp lumens that reaches the working plane
  2. The voltage drop
  3. The lamp life
  4. The cost of lamps
Show answer & solution

Answer: (A) The fraction of lamp lumens that reaches the working plane

It depends on room shape, surface reflectances and luminaire type.

Question 13

What does the maintenance factor in lighting design account for?

  1. Cost of maintenance
  2. Increase of light with time
  3. Number of switches
  4. Reduction of light output due to dirt and lamp ageing
Show answer & solution

Answer: (D) Reduction of light output due to dirt and lamp ageing

Typical values are about 0.7–0.8.

Question 14

What illuminance level is generally recommended for general office work?

  1. About 5 lux
  2. About 300 to 500 lux
  3. About 5,000 lux
  4. About 50,000 lux
Show answer & solution

Answer: (B) About 300 to 500 lux

Detailed tasks need higher levels.

Question 15

What does the colour temperature of a lamp describe?

  1. The appearance of its light, from warm (yellowish) to cool (bluish), in kelvin
  2. The lamp voltage
  3. The heat produced
  4. The lamp's surface temperature
Show answer & solution

Answer: (A) The appearance of its light, from warm (yellowish) to cool (bluish), in kelvin

Warm white is about 2,700–3,000 K and daylight about 6,500 K.

Question 16

What does the colour rendering index (CRI) indicate?

  1. The lamp's efficacy
  2. The beam angle
  3. The lamp's life
  4. How accurately a light source shows colours compared with natural light
Show answer & solution

Answer: (D) How accurately a light source shows colours compared with natural light

A CRI above 80 is good for most indoor uses.

Question 17

Which lamp type, giving yellow light and high efficacy, was widely used for street lighting?

  1. Incandescent lamp
  2. Halogen lamp
  3. Neon lamp
  4. Low- or high-pressure sodium vapour lamp
Show answer & solution

Answer: (D) Low- or high-pressure sodium vapour lamp

LED street lights are now replacing sodium lamps.

Question 18

What is glare in lighting?

  1. Too little light
  2. Even lighting
  3. Excessive brightness or contrast that causes discomfort or reduces visibility
  4. A type of lamp
Show answer & solution

Answer: (C) Excessive brightness or contrast that causes discomfort or reduces visibility

Diffusers and proper luminaire positioning reduce glare.

Question 19

What is the space-to-height ratio in lighting design?

  1. The ratio of spacing between luminaires to their mounting height above the working plane
  2. The ratio of room length to width
  3. The lamp efficacy
  4. The number of lamps
Show answer & solution

Answer: (A) The ratio of spacing between luminaires to their mounting height above the working plane

Keeping within the luminaire's limit gives uniform lighting.

Question 20

Which instrument measures illuminance?

  1. Anemometer
  2. Lux meter
  3. Pyranometer
  4. Megger
Show answer & solution

Answer: (B) Lux meter

It uses a photocell with a colour-corrected filter.

Question 21

What is a metal halide lamp mainly used for?

  1. Floodlighting and sports lighting needing good colour rendering
  2. Torches
  3. Indicator lights
  4. Night lights
Show answer & solution

Answer: (A) Floodlighting and sports lighting needing good colour rendering

They are being replaced by high-power LEDs.

Question 22

What is the luminous efficacy of a 10 W LED lamp producing 1,000 lumens?

  1. 0.01 lm/W
  2. 10 lm/W
  3. 100 lm/W
  4. 1,000 lm/W
Show answer & solution

Answer: (C) 100 lm/W

Efficacy = 1,000/10.

Question 23

What is the main reason LED lighting saves energy compared with incandescent lamps?

  1. LEDs work only in daylight
  2. LEDs use higher voltage
  3. LEDs are larger
  4. LEDs convert a much larger fraction of input power into light rather than heat
Show answer & solution

Answer: (D) LEDs convert a much larger fraction of input power into light rather than heat

Incandescent lamps convert about 95% of input into heat.

Question 24

What is the purpose of a photocell switch on street lights?

  1. To protect against lightning
  2. To switch lights on at dusk and off at dawn automatically
  3. To dim lamps manually
  4. To measure power
Show answer & solution

Answer: (B) To switch lights on at dusk and off at dawn automatically

It saves energy and labour.

Question 25

What is uniformity ratio in lighting?

  1. The ratio of minimum to average illuminance over an area
  2. The lamp efficacy
  3. The colour temperature
  4. The ratio of lamps to switches
Show answer & solution

Answer: (A) The ratio of minimum to average illuminance over an area

High uniformity avoids dark spots.

Question 26

What is a lumen?

  1. The light on one square metre
  2. The luminous flux emitted within one steradian by a source of one candela
  3. The power of one watt
  4. The intensity of one lamp
Show answer & solution

Answer: (B) The luminous flux emitted within one steradian by a source of one candela

A uniform 1 cd point source emits 4π lumens in total.

Question 27

What is the main advantage of LED street lighting over sodium lamps?

  1. Lower efficacy
  2. Shorter life
  3. Yellow light only
  4. Higher efficacy, better colour rendering and longer life with dimming control
Show answer & solution

Answer: (D) Higher efficacy, better colour rendering and longer life with dimming control

Many cities are replacing sodium lamps with LEDs.

Question 28

What is the purpose of a reflector in a luminaire?

  1. To direct light where it is needed and increase useful illuminance
  2. To increase glare
  3. To cool the lamp
  4. To absorb light
Show answer & solution

Answer: (A) To direct light where it is needed and increase useful illuminance

Reflector design shapes the light distribution.

Practice these 28 questions interactively →