Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Utilisation & Electrical Installation: Electric Traction

Electrical Engineering · Utilisation & Electrical Installation

26 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Why were DC series motors traditionally used for electric traction?

  1. They run at constant speed
  2. They need no control
  3. They give very high starting torque and naturally slow down under heavy load
  4. They have no commutator
Show answer & solution

Answer: (C) They give very high starting torque and naturally slow down under heavy load

Modern traction uses inverter-fed AC motors.

Question 2

Which motor drive is used in most modern electric trains and metros?

  1. Stepper motors
  2. Universal motors
  3. DC shunt motors only
  4. Three-phase induction or permanent magnet motors fed by variable voltage variable frequency inverters
Show answer & solution

Answer: (D) Three-phase induction or permanent magnet motors fed by variable voltage variable frequency inverters

They offer high efficiency and regenerative braking.

Question 3

What is the standard overhead supply used for main-line AC electrified railways?

  1. 11 kV three-phase
  2. 25 kV, 50 Hz single-phase
  3. 132 kV three-phase
  4. 400 V three-phase
Show answer & solution

Answer: (B) 25 kV, 50 Hz single-phase

It allows widely spaced feeding substations.

Question 4

Which device collects current from the overhead line on an electric locomotive?

  1. Slip ring only
  2. Buchholz relay
  3. Commutator
  4. Pantograph
Show answer & solution

Answer: (D) Pantograph

The pantograph slides along the contact wire.

Question 5

What is the overhead wire system that supplies electric trains called?

  1. Catenary (overhead contact) system
  2. Earth wire
  3. Third rail only
  4. Bus bar
Show answer & solution

Answer: (A) Catenary (overhead contact) system

A messenger wire supports the contact wire at constant height.

Question 6

What is a third-rail system?

  1. An overhead wire
  2. A brake
  3. A supply rail beside the running rails from which trains collect DC current
  4. A signalling system
Show answer & solution

Answer: (C) A supply rail beside the running rails from which trains collect DC current

It is used in many metro systems at about 600–750 V DC.

Question 7

What is regenerative braking in electric traction?

  1. Using traction motors as generators to return braking energy to the supply
  2. Using air brakes only
  3. Disconnecting motors
  4. Using friction brakes only
Show answer & solution

Answer: (A) Using traction motors as generators to return braking energy to the supply

It saves energy, especially in metros with frequent stops.

Question 8

What are the main periods of a typical speed–time curve for a train run?

  1. Braking only
  2. Acceleration, free running, coasting and braking
  3. Constant speed only
  4. Starting and stopping only
Show answer & solution

Answer: (B) Acceleration, free running, coasting and braking

Coasting saves energy by running with power off.

Question 9

What is crest speed of a train?

  1. The speed at stops
  2. The schedule speed
  3. The average speed
  4. The maximum speed reached during a run
Show answer & solution

Answer: (D) The maximum speed reached during a run

Crest speed is reached at the end of acceleration or free running.

Question 10

What is the average speed of a train?

  1. The speed at coasting
  2. Distance divided by total time including stops
  3. Distance between stops divided by actual running time
  4. The maximum speed
Show answer & solution

Answer: (C) Distance between stops divided by actual running time

Schedule speed includes stop times.

Question 11

What is schedule speed?

  1. The braking speed
  2. Distance divided by running time only
  3. The maximum speed
  4. Distance between terminals divided by total time including stops
Show answer & solution

Answer: (D) Distance between terminals divided by total time including stops

Frequent stops reduce schedule speed.

Question 12

What is the schedule speed of a train covering 10 km in 15 minutes including stops?

  1. 15 km/h
  2. 25 km/h
  3. 40 km/h
  4. 60 km/h
Show answer & solution

Answer: (C) 40 km/h

10 km ÷ 0.25 h = 40 km/h.

Question 13

What is the coefficient of adhesion in electric traction?

  1. The ratio of maximum tractive effort without slipping to the weight on driving wheels
  2. The braking time
  3. The train weight
  4. The motor efficiency
Show answer & solution

Answer: (A) The ratio of maximum tractive effort without slipping to the weight on driving wheels

Wet rails reduce adhesion.

Question 14

What is tractive effort?

  1. The speed of the train
  2. The force exerted by the locomotive at the wheel rims to move the train
  3. The power of the supply
  4. The weight of the train
Show answer & solution

Answer: (B) The force exerted by the locomotive at the wheel rims to move the train

It must overcome train resistance, gradient and acceleration.

Question 15

Which section of Pakistan Railways was electrified with 25 kV AC traction in the 1960s and 1970s?

  1. Rawalpindi–Attock only
  2. Quetta–Taftan
  3. Karachi–Peshawar
  4. Lahore–Khanewal
Show answer & solution

Answer: (D) Lahore–Khanewal

Electric operation on this section ended in the early 2010s.

Question 16

What is the main advantage of electric traction over diesel traction?

  1. No need for supply infrastructure
  2. Need for fuel tanks
  3. Higher efficiency, no exhaust at the point of use and regenerative braking
  4. More noise
Show answer & solution

Answer: (C) Higher efficiency, no exhaust at the point of use and regenerative braking

Electrification has high initial cost.

Question 17

What is the main disadvantage of electric traction?

  1. High running cost compared with diesel
  2. High initial cost of overhead lines and substations
  3. More pollution at the train
  4. Lower acceleration
Show answer & solution

Answer: (B) High initial cost of overhead lines and substations

It is most economic on busy routes.

Question 18

What is the main function of a booster transformer in AC traction systems?

  1. To force return current through the return conductor and reduce interference with communication lines
  2. To increase voltage
  3. To start motors
  4. To brake trains
Show answer & solution

Answer: (A) To force return current through the return conductor and reduce interference with communication lines

Autotransformer systems are also used.

Question 19

What is the specific energy consumption of a train?

  1. Energy per passenger only
  2. Motor power
  3. Total energy per day
  4. Energy consumed per tonne-km
Show answer & solution

Answer: (D) Energy consumed per tonne-km

It depends on stops, gradients and speed profile.

Question 20

What type of motor is used in most electric vehicles today?

  1. Shaded-pole motors
  2. Stepper motors
  3. Permanent magnet synchronous or induction motors
  4. Universal motors
Show answer & solution

Answer: (C) Permanent magnet synchronous or induction motors

Inverters control speed and torque.

Question 21

What is coasting in a train run?

  1. Running with power switched off, letting the train slow gradually
  2. Applying full brakes
  3. Stopping at a station
  4. Running at full power
Show answer & solution

Answer: (A) Running with power switched off, letting the train slow gradually

Coasting reduces energy consumption.

Question 22

What is the main reason trains use series-wound or inverter-fed motors with high starting torque?

  1. Trains are very light
  2. Trains run at constant speed
  3. Trains never stop
  4. Trains need large tractive effort to accelerate heavy loads from rest
Show answer & solution

Answer: (D) Trains need large tractive effort to accelerate heavy loads from rest

Starting resistance is the largest at standstill.

Question 23

Which mass transit system in Lahore runs on electric traction?

  1. Green Line BRT bus only
  2. Orange Line Metro Train
  3. Karachi Circular Railway diesel service
  4. Khyber Mail
Show answer & solution

Answer: (B) Orange Line Metro Train

It was Pakistan's first metro rail line.

Question 24

What is dynamic (rheostatic) braking in traction?

  1. Returning energy to the supply
  2. Disconnecting the motors
  3. Using the motors as generators and dissipating the energy in resistors
  4. Using air brakes only
Show answer & solution

Answer: (C) Using the motors as generators and dissipating the energy in resistors

It is used when regeneration is not possible.

Question 25

Why is AC 25 kV used for main-line electrification rather than low-voltage DC?

  1. Lower current means fewer substations and smaller conductors for long routes
  2. AC has no losses
  3. AC needs no substations
  4. DC cannot drive motors
Show answer & solution

Answer: (A) Lower current means fewer substations and smaller conductors for long routes

DC is used mainly for metros and trams.

Question 26

What is train resistance?

  1. The motor resistance
  2. The brake force
  3. The electrical resistance of rails
  4. The opposing force due to friction, air resistance and track effects
Show answer & solution

Answer: (D) The opposing force due to friction, air resistance and track effects

It increases with speed.

Practice these 26 questions interactively →