Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power System Protection: Protective Relays

Electrical Engineering · Power System Protection

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which relay measures the apparent impedance between its location and a transmission line fault?

  1. Distance relay
  2. Differential relay
  3. Thermal relay
  4. Frequency relay
Show answer & solution

Answer: (A) Distance relay

It compares the voltage and current at the relay point.

Question 2

Which distance relay characteristic is inherently directional?

  1. Mho relay
  2. Overcurrent relay
  3. Plain impedance relay
  4. Thermal relay
Show answer & solution

Answer: (A) Mho relay

Its circle passes through the origin of the R–X diagram.

Question 3

Which distance relay is least affected by arc resistance and suits short lines?

  1. Impedance relay
  2. Reactance relay
  3. Mho relay
  4. Offset mho relay only for long lines
Show answer & solution

Answer: (B) Reactance relay

It measures only the reactive component of impedance.

Question 4

What portion of the protected line is usually covered by zone 1 of a distance relay?

  1. Only 10%
  2. The whole adjacent line
  3. About 80 to 90%, with instantaneous tripping
  4. About 150% with a long delay
Show answer & solution

Answer: (C) About 80 to 90%, with instantaneous tripping

Zone 1 is set short of the remote end to avoid overreach.

Question 5

What is the purpose of zone 2 in distance protection?

  1. To give no protection
  2. To trip instantaneously for all faults
  3. To protect only busbars
  4. To cover the rest of the line and part of the next line with a time delay
Show answer & solution

Answer: (D) To cover the rest of the line and part of the next line with a time delay

Zone 2 is typically set to about 120% of the line.

Question 6

What is the purpose of zone 3 in distance protection?

  1. To provide backup protection for adjacent lines with a longer time delay
  2. To detect lightning
  3. To reclose the breaker
  4. To protect only the first 10% of the line
Show answer & solution

Answer: (A) To provide backup protection for adjacent lines with a longer time delay

Zone 3 must be set carefully to avoid tripping on load or power swings.

Question 7

What is the primary purpose of power-swing blocking in a distance protection scheme?

  1. To increase relay sensitivity
  2. To accelerate zone 3 tripping
  3. To prevent unwanted line tripping during stable power swings
  4. To detect transformer inrush
Show answer & solution

Answer: (C) To prevent unwanted line tripping during stable power swings

Power swings can make the measured impedance enter relay zones without a fault.

Question 8

On which principle does a differential relay operate?

  1. It measures impedance
  2. It measures frequency
  3. It measures temperature
  4. It compares currents entering and leaving the protected zone and operates on their difference
Show answer & solution

Answer: (D) It compares currents entering and leaving the protected zone and operates on their difference

Merz–Price circulating current schemes use this principle.

Question 9

What is a biased (percentage) differential relay?

  1. A relay with no restraint
  2. A differential relay whose operating current must exceed a percentage of the through current
  3. An overcurrent relay
  4. A distance relay
Show answer & solution

Answer: (B) A differential relay whose operating current must exceed a percentage of the through current

Bias prevents mal-operation from CT mismatch during heavy through faults.

Question 10

What does a directional overcurrent relay need besides current to determine fault direction?

  1. A polarising voltage
  2. Temperature
  3. Speed
  4. Frequency only
Show answer & solution

Answer: (A) A polarising voltage

It is used in ring mains and parallel feeders.

Question 11

On which principle does an induction disc relay operate?

  1. Hall effect
  2. Torque on a metal disc produced by interacting eddy currents from two alternating fluxes
  3. Thermal expansion of a bimetal
  4. Electrostatic attraction
Show answer & solution

Answer: (B) Torque on a metal disc produced by interacting eddy currents from two alternating fluxes

It is the basis of electromechanical IDMT relays.

Question 12

What is an attracted armature relay?

  1. A relay using a bimetal strip
  2. A relay using gas pressure
  3. A relay using a rotating disc
  4. A relay in which an electromagnet attracts an iron armature to close contacts
Show answer & solution

Answer: (D) A relay in which an electromagnet attracts an iron armature to close contacts

It is fast and used for instantaneous protection.

Question 13

Which relay protects a generator against motoring when its prime mover fails?

  1. Under-voltage relay
  2. Buchholz relay
  3. Reverse power relay
  4. Distance relay
Show answer & solution

Answer: (C) Reverse power relay

Motoring can damage steam turbines.

Question 14

Which relay protects a generator against unbalanced loading that overheats the rotor?

  1. Negative-sequence relay
  2. Directional earth fault relay
  3. Over-voltage relay
  4. Reverse power relay
Show answer & solution

Answer: (A) Negative-sequence relay

Unbalanced currents induce double-frequency rotor currents.

Question 15

What does an under-frequency relay do in a power system?

  1. It protects against lightning
  2. It disconnects selected loads when frequency falls below set values
  3. It measures energy
  4. It increases frequency directly
Show answer & solution

Answer: (B) It disconnects selected loads when frequency falls below set values

It is used for automatic load shedding.

Question 16

What does a check synchronising relay ensure before closing a breaker?

  1. The load is zero
  2. The breaker is open
  3. Voltage, frequency and phase angle are within limits on both sides
  4. The CT is shorted
Show answer & solution

Answer: (C) Voltage, frequency and phase angle are within limits on both sides

ANSI device 25 is the synchronism check relay.

Question 17

What does an auto-reclosing relay do?

  1. It opens a breaker permanently
  2. It blocks all tripping
  3. It measures insulation
  4. It automatically recloses a breaker after a set dead time following a trip
Show answer & solution

Answer: (D) It automatically recloses a breaker after a set dead time following a trip

Most overhead line faults are transient.

Question 18

What is the function of a lockout relay (ANSI 86)?

  1. To trip breakers and prevent reclosing until reset manually
  2. To supervise trip circuits
  3. To measure power
  4. To reclose breakers quickly
Show answer & solution

Answer: (A) To trip breakers and prevent reclosing until reset manually

It is used for faults where reclosing would be dangerous, such as transformer faults.

Question 19

Which relay responds to the heating effect of current to protect against overloads?

  1. Differential relay
  2. Thermal relay
  3. Buchholz relay
  4. Distance relay
Show answer & solution

Answer: (B) Thermal relay

Thermal relays model the temperature rise of the protected equipment.

Question 20

What is an earth fault relay?

  1. A relay that protects against lightning
  2. A relay that measures voltage only
  3. A relay that responds to frequency
  4. A relay that responds to residual (zero-sequence) current flowing to earth
Show answer & solution

Answer: (D) A relay that responds to residual (zero-sequence) current flowing to earth

Residual current is obtained from three CTs connected in parallel or a core-balance CT.

Question 21

What is a core-balance CT used for?

  1. Measuring frequency
  2. Measuring load current
  3. Sensitive earth fault detection by passing all phase conductors through one CT
  4. Measuring voltage
Show answer & solution

Answer: (C) Sensitive earth fault detection by passing all phase conductors through one CT

Under normal balanced conditions the net flux is zero.

Question 22

What is carrier (teleprotection) aided distance protection?

  1. A lightning protection scheme
  2. A protection using fuses
  3. A protection using thermal relays
  4. A scheme using communication between line ends to clear end-zone faults instantaneously
Show answer & solution

Answer: (D) A scheme using communication between line ends to clear end-zone faults instantaneously

Permissive and blocking schemes are common.

Question 23

What is pilot-wire protection?

  1. A frequency scheme
  2. A lightning protection
  3. A differential scheme for short lines using wires to compare currents at both ends
  4. An overcurrent scheme
Show answer & solution

Answer: (C) A differential scheme for short lines using wires to compare currents at both ends

Modern schemes use fibre optic communication instead.

Question 24

What is the main advantage of static relays over electromechanical relays?

  1. Low burden, fast operation and no moving parts
  2. They cannot fail
  3. They are larger
  4. They need no power supply
Show answer & solution

Answer: (A) Low burden, fast operation and no moving parts

Static relays use electronic circuits.

Question 25

Which relay protects against over-fluxing of transformers and generators?

  1. Earth fault relay
  2. Volts-per-hertz relay
  3. Distance relay
  4. Reverse power relay
Show answer & solution

Answer: (B) Volts-per-hertz relay

Over-excitation occurs when V/f exceeds limits.

Question 26

What is the function of a breaker failure protection (ANSI 50BF)?

  1. To supervise batteries
  2. To reclose breakers
  3. To trip adjacent breakers if the main breaker fails to clear a fault
  4. To measure current
Show answer & solution

Answer: (C) To trip adjacent breakers if the main breaker fails to clear a fault

It provides fast local backup.

Question 27

What is meant by relay overreach?

  1. Failure to operate for faults within reach
  2. Very slow operation
  3. Operation only at no load
  4. Operation of a relay for faults beyond its intended reach
Show answer & solution

Answer: (D) Operation of a relay for faults beyond its intended reach

Underreach is the opposite.

Question 28

Why is a directional earth fault relay used in parallel feeders or ring mains?

  1. To trip only the feeder carrying fault current in the fault direction
  2. To trip all feeders
  3. To measure voltage
  4. To protect transformers only
Show answer & solution

Answer: (A) To trip only the feeder carrying fault current in the fault direction

Without direction, healthy feeders might trip.

Question 29

Which relay is used to detect loss of excitation in a generator?

  1. Earth fault relay
  2. Loss-of-field (offset mho) relay
  3. Over-voltage relay
  4. Buchholz relay
Show answer & solution

Answer: (B) Loss-of-field (offset mho) relay

Loss of excitation makes the generator draw reactive power from the system.

Question 30

What does the ANSI device number 21 represent?

  1. Overcurrent relay
  2. Distance relay
  3. Differential relay
  4. Reclosing relay
Show answer & solution

Answer: (B) Distance relay

Distance relays protect transmission lines.

Question 31

What does the ANSI device number 67 represent?

  1. Distance relay
  2. Frequency relay
  3. Directional overcurrent relay
  4. Lockout relay
Show answer & solution

Answer: (C) Directional overcurrent relay

It operates only for faults in a chosen direction.

Question 32

What does the ANSI device number 81 represent?

  1. Reverse power relay
  2. Synchronism check relay
  3. Lockout relay
  4. Frequency relay
Show answer & solution

Answer: (D) Frequency relay

Under- and over-frequency elements are designated 81U and 81O.

Question 33

What does the ANSI device number 79 represent?

  1. Auto-reclosing relay
  2. Distance relay
  3. Thermal relay
  4. Overcurrent relay
Show answer & solution

Answer: (A) Auto-reclosing relay

Reclosers are used on overhead lines.

Question 34

Why is an offset mho characteristic sometimes used in zone 3 of distance relays?

  1. To measure frequency
  2. To cover close-in faults behind the relay and provide reliable backup
  3. To reduce reach
  4. To prevent all tripping
Show answer & solution

Answer: (B) To cover close-in faults behind the relay and provide reliable backup

The circle is shifted to include the origin.

Question 35

What is a permissive overreach transfer trip (POTT) scheme?

  1. A scheme where an overreaching zone trips only when a permissive signal is received from the remote end
  2. A scheme with no communication
  3. A thermal scheme
  4. A scheme using fuses
Show answer & solution

Answer: (A) A scheme where an overreaching zone trips only when a permissive signal is received from the remote end

It gives fast tripping for faults anywhere on the line.

Question 36

Which relay gives almost instantaneous operation independent of fault current magnitude above its setting?

  1. Definite minimum time relay with long delay
  2. Thermal relay
  3. Instantaneous overcurrent relay
  4. IDMT relay
Show answer & solution

Answer: (C) Instantaneous overcurrent relay

Instantaneous elements are set above the maximum through-fault current.

Question 37

What is the main limitation of a plain impedance relay?

  1. It is affected only by frequency
  2. It cannot be set
  3. It cannot measure impedance
  4. It is non-directional and needs a separate directional element
Show answer & solution

Answer: (D) It is non-directional and needs a separate directional element

Its characteristic is a circle centred on the origin.

Practice these 37 questions interactively →