Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power System Protection: Fuses and LV Protection

Electrical Engineering · Power System Protection

33 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

On what principle does a fuse protect a circuit?

  1. It stores energy
  2. It reverses current
  3. A fuse element melts when excessive current flows and opens the circuit
  4. It measures voltage
Show answer & solution

Answer: (C) A fuse element melts when excessive current flows and opens the circuit

It is the simplest overcurrent protective device.

Question 2

What is the purpose of silica sand filling in an HRC fuse?

  1. To increase current
  2. To conduct electricity
  3. To cool the load
  4. To absorb arc energy and quench the arc quickly
Show answer & solution

Answer: (D) To absorb arc energy and quench the arc quickly

HRC fuses have high rupturing capacity.

Question 3

What is the fusing factor of a fuse?

  1. Melting time divided by current
  2. Minimum fusing current divided by current rating
  3. Voltage rating divided by current
  4. Current rating divided by minimum fusing current
Show answer & solution

Answer: (B) Minimum fusing current divided by current rating

The fusing factor is always greater than one.

Question 4

What is the cut-off current of a current-limiting fuse?

  1. The peak current reached before the fuse interrupts, lower than the prospective peak
  2. The voltage at which it melts
  3. The normal load current
  4. The minimum fusing current
Show answer & solution

Answer: (A) The peak current reached before the fuse interrupts, lower than the prospective peak

Current limitation reduces thermal and mechanical stress.

Question 5

What is the main disadvantage of a rewireable (kit-kat) fuse?

  1. It cannot melt
  2. Unreliable operation because a wrong wire size can be fitted
  3. Very high cost
  4. Very fast operation
Show answer & solution

Answer: (B) Unreliable operation because a wrong wire size can be fitted

Overrated wire removes protection.

Question 6

What does the I²t value of a fuse represent?

  1. The resistance of the fuse
  2. The current rating
  3. The let-through energy during fault interruption
  4. The voltage rating
Show answer & solution

Answer: (C) The let-through energy during fault interruption

It is used to coordinate fuses with equipment withstand.

Question 7

Which two trip elements are combined in a miniature circuit breaker (MCB)?

  1. A thermal element for overload and a magnetic element for short circuit
  2. A voltage element and a frequency element
  3. A gas element and a thermal element
  4. A Buchholz element and a magnetic element
Show answer & solution

Answer: (A) A thermal element for overload and a magnetic element for short circuit

Thermal trips are slow and magnetic trips are instantaneous.

Question 8

What is the magnetic trip range of a Type B MCB?

  1. 3 to 5 times rated current
  2. 5 to 10 times rated current
  3. 10 to 20 times rated current
  4. 20 to 50 times rated current
Show answer & solution

Answer: (A) 3 to 5 times rated current

Type B suits resistive and domestic lighting loads.

Question 9

Which MCB type suits motors and transformers with high inrush currents?

  1. Type A
  2. Type Z
  3. Type B
  4. Type D
Show answer & solution

Answer: (D) Type D

Type D trips magnetically at 10–20 times rated current.

Question 10

What does a residual current device (RCD) detect?

  1. Overvoltage
  2. Overload current only
  3. Low frequency
  4. An imbalance between line and neutral currents caused by leakage to earth
Show answer & solution

Answer: (D) An imbalance between line and neutral currents caused by leakage to earth

RCDs protect against electric shock and fire.

Question 11

What rated residual operating current is used for RCDs that protect people from electric shock?

  1. 3 A
  2. 30 A
  3. 30 mA
  4. 300 mA
Show answer & solution

Answer: (C) 30 mA

A 30 mA RCD operates before a dangerous shock current flows for long.

Question 12

Which device combines an RCD with overcurrent protection in one unit?

  1. MCCB only
  2. RCBO
  3. Isolator
  4. HRC fuse
Show answer & solution

Answer: (B) RCBO

RCBOs protect individual circuits against both earth leakage and overcurrent.

Question 13

What protects a motor against overload in a direct-on-line starter?

  1. A thermal overload relay with the contactor
  2. A Buchholz relay
  3. A surge arrester
  4. An isolator
Show answer & solution

Answer: (A) A thermal overload relay with the contactor

The overload relay opens the contactor coil circuit.

Question 14

What is the main function of a contactor?

  1. To protect against lightning
  2. To interrupt high fault currents
  3. To measure power
  4. To switch circuits on and off frequently by remote or automatic control
Show answer & solution

Answer: (D) To switch circuits on and off frequently by remote or automatic control

Contactors are not designed to clear short circuits alone.

Question 15

Which fuse is commonly used on 11 kV overhead lines and transformer poles in Pakistan?

  1. Rewireable fuse
  2. HRC cartridge fuse for 400 V only
  3. Drop-out (expulsion) fuse
  4. Glass fuse
Show answer & solution

Answer: (C) Drop-out (expulsion) fuse

When it blows, the fuse holder drops to show operation.

Question 16

What is discrimination between two fuses in series?

  1. Both fuses operate together
  2. Only the fuse nearest the fault operates
  3. The upstream fuse always operates first
  4. Neither fuse operates
Show answer & solution

Answer: (B) Only the fuse nearest the fault operates

A rating ratio of about 2:1 often ensures discrimination.

Question 17

Why is an MCB preferred over a rewireable fuse in modern installations?

  1. It is cheaper in all cases
  2. It never trips
  3. It needs no installation
  4. It can be reset, trips reliably and gives both overload and short-circuit protection
Show answer & solution

Answer: (D) It can be reset, trips reliably and gives both overload and short-circuit protection

MCBs also act as switches.

Question 18

What is the purpose of a surge protective device (SPD) in a low-voltage installation?

  1. To divert transient overvoltages from lightning or switching to earth
  2. To measure current
  3. To protect against overload
  4. To improve power factor
Show answer & solution

Answer: (A) To divert transient overvoltages from lightning or switching to earth

SPDs protect sensitive electronics.

Question 19

What is an earth leakage circuit breaker (ELCB)?

  1. A surge arrester
  2. A fuse for street lights
  3. A device that disconnects supply when earth leakage current exceeds a set value
  4. A switch for lighting
Show answer & solution

Answer: (C) A device that disconnects supply when earth leakage current exceeds a set value

Voltage-operated ELCBs have been replaced by current-operated RCDs.

Question 20

Why should the neutral not be fused separately in a single-phase circuit?

  1. It is required by IEC
  2. If the neutral fuse blows, the circuit stays live through the phase conductor
  3. It improves safety
  4. It reduces cost
Show answer & solution

Answer: (B) If the neutral fuse blows, the circuit stays live through the phase conductor

Only the phase conductor should be protected by a single-pole device.

Question 21

What is the breaking capacity rating of a domestic MCB typically?

  1. 1 A
  2. 6 kA or 10 kA
  3. 100 kA
  4. 500 kA
Show answer & solution

Answer: (B) 6 kA or 10 kA

It must exceed the prospective fault current at its location.

Question 22

What is single-phasing protection for three-phase motors?

  1. Protection against overvoltage only
  2. Protection against lightning
  3. Protection that trips the motor when one supply phase is lost
  4. Protection against high frequency
Show answer & solution

Answer: (C) Protection that trips the motor when one supply phase is lost

A motor running on two phases overheats quickly.

Question 23

What does an under-voltage release in a motor starter do?

  1. It disconnects the motor when supply voltage falls too low
  2. It improves power factor
  3. It increases voltage
  4. It measures speed
Show answer & solution

Answer: (A) It disconnects the motor when supply voltage falls too low

It prevents automatic restart when supply returns.

Question 24

What does the time–current characteristic of a fuse show?

  1. The resistance against temperature
  2. The cost of the fuse
  3. The voltage of the fuse
  4. The time taken for the fuse to operate at different currents
Show answer & solution

Answer: (D) The time taken for the fuse to operate at different currents

Higher currents give shorter operating times.

Question 25

What is a semiconductor (high-speed) fuse used for?

  1. Protecting thyristors, diodes and other power electronic devices
  2. Protecting transmission lines
  3. Protecting transformers from lightning
  4. Protecting houses
Show answer & solution

Answer: (A) Protecting thyristors, diodes and other power electronic devices

They have very low I²t values.

Question 26

What is the function of a load-break switch?

  1. To switch normal load currents but not fault currents
  2. To protect against lightning
  3. To measure power
  4. To clear short circuits
Show answer & solution

Answer: (A) To switch normal load currents but not fault currents

It is often combined with fuses in ring main units.

Question 27

What is a fuse–switch combination?

  1. A breaker with no fuse
  2. A surge arrester
  3. A switch that also carries fuses, providing isolation and short-circuit protection
  4. A relay
Show answer & solution

Answer: (C) A switch that also carries fuses, providing isolation and short-circuit protection

It is common in LV distribution boards.

Question 28

Why should fuses be replaced with the correct rating and type?

  1. Any fuse gives the same protection
  2. Fuse rating has no effect
  3. An incorrect fuse may fail to protect cables and equipment or cause unwanted operation
  4. Higher rated fuses are always safer
Show answer & solution

Answer: (C) An incorrect fuse may fail to protect cables and equipment or cause unwanted operation

Fuses are coordinated with cable ratings.

Question 29

What is the main purpose of cable protection by overcurrent devices?

  1. To improve power factor
  2. To prevent conductor temperature exceeding safe limits under overload or fault
  3. To reduce voltage drop
  4. To increase current
Show answer & solution

Answer: (B) To prevent conductor temperature exceeding safe limits under overload or fault

The device rating must not exceed cable current capacity.

Question 30

Why are Type C MCBs used for commercial and light industrial circuits?

  1. They trip at very low currents
  2. They are for DC only
  3. They need no breaking capacity
  4. They tolerate moderate inrush currents of fluorescent lighting and small motors
Show answer & solution

Answer: (D) They tolerate moderate inrush currents of fluorescent lighting and small motors

Type C trips magnetically at 5–10 times rated current.

Question 31

What does an RCD not protect against?

  1. Overloads and short circuits between line and neutral that have no earth leakage
  2. Earth fault fires
  3. Earth leakage shocks
  4. Leakage through damaged insulation to earth
Show answer & solution

Answer: (A) Overloads and short circuits between line and neutral that have no earth leakage

It must be combined with overcurrent protection.

Question 32

What is the purpose of the test button on an RCD?

  1. To check that the tripping mechanism works by creating a small imbalance
  2. To reset the MCB
  3. To measure voltage
  4. To change the setting
Show answer & solution

Answer: (A) To check that the tripping mechanism works by creating a small imbalance

RCDs should be tested regularly.

Question 33

What protection is provided by a motor protection circuit breaker (MPCB)?

  1. Lightning protection
  2. Frequency control
  3. Power factor correction
  4. Combined overload, short-circuit and phase-loss protection for motors
Show answer & solution

Answer: (D) Combined overload, short-circuit and phase-loss protection for motors

MPCBs replace separate fuses and overload relays.

Practice these 33 questions interactively →