Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Electronics: Rectifiers

Electrical Engineering · Power Electronics

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the average output voltage of a single-phase half-wave uncontrolled rectifier with peak input voltage Vm?

  1. Vm/√2
  2. 2Vm/π
  3. Vm/π
  4. Vm
Show answer & solution

Answer: (C) Vm/π

Average value of a half-wave rectified sine is 0.318Vm.

Question 2

What is the average output voltage of a single-phase full-wave uncontrolled rectifier with peak voltage Vm?

  1. 2Vm/π
  2. Vm/2
  3. √2 Vm
  4. Vm/π
Show answer & solution

Answer: (A) 2Vm/π

This equals about 0.637Vm.

Question 3

What is the ripple factor of a single-phase half-wave rectifier without a filter?

  1. 0.04
  2. 0.482
  3. 1.21
  4. 2.0
Show answer & solution

Answer: (C) 1.21

Ripple is very high for half-wave rectification.

Question 4

What is the ripple factor of a single-phase full-wave rectifier without a filter?

  1. 0.1
  2. 0.482
  3. 1.0
  4. 1.21
Show answer & solution

Answer: (B) 0.482

Full-wave rectification halves the relative ripple.

Question 5

What is the maximum rectification efficiency of a half-wave rectifier?

  1. 25%
  2. 40.6%
  3. 81.2%
  4. 100%
Show answer & solution

Answer: (B) 40.6%

Full-wave rectifiers reach 81.2%.

Question 6

What is the peak inverse voltage across each diode in a single-phase bridge rectifier?

  1. 4Vm
  2. 2Vm
  3. Vm/2
  4. Vm
Show answer & solution

Answer: (D) Vm

In a centre-tapped rectifier each diode sees 2Vm.

Question 7

What is the peak inverse voltage across each diode in a centre-tapped full-wave rectifier?

  1. Vm
  2. 3Vm
  3. Vm/2
  4. 2Vm
Show answer & solution

Answer: (D) 2Vm

This is a disadvantage of the centre-tapped circuit.

Question 8

What is the approximate DC output of a single-phase full-wave diode bridge fed from 230 V RMS without a filter?

  1. About 115 V
  2. About 207 V
  3. About 230 V
  4. About 325 V
Show answer & solution

Answer: (B) About 207 V

Vdc = 2 × 325/π ≈ 207 V.

Question 9

What is the average output voltage of a single-phase fully controlled bridge with continuous current at firing angle α?

  1. (2Vm/π) cos α
  2. (Vm/π)(1 + cos α)
  3. Vm cos α
  4. (2Vm/π)(1 − cos α)
Show answer & solution

Answer: (A) (2Vm/π) cos α

It becomes negative for α greater than 90°.

Question 10

What is the average output voltage of a single-phase half-controlled (semi-converter) bridge?

  1. (Vm/π)(1 + cos α)
  2. (2Vm/π) cos α
  3. Vm(1 − cos α)
  4. (Vm/π) cos α
Show answer & solution

Answer: (A) (Vm/π)(1 + cos α)

A semi-converter cannot give negative average voltage.

Question 11

When does a fully controlled converter operate as an inverter?

  1. When the gate is removed
  2. When the load is purely resistive
  3. When the firing angle exceeds 90° with a suitable DC source in the load
  4. When the firing angle is zero
Show answer & solution

Answer: (C) When the firing angle exceeds 90° with a suitable DC source in the load

Energy then flows from the DC side to the AC supply.

Question 12

What is the average output voltage of a three-phase fully controlled bridge with line voltage VL at firing angle α?

  1. 0.45 VL cos α
  2. 0.9 VL cos α
  3. 1.35 VL cos α
  4. 2.34 VL cos α
Show answer & solution

Answer: (C) 1.35 VL cos α

1.35 = 3√2/π for line-to-line RMS voltage.

Question 13

What is the approximate DC output voltage of a three-phase diode bridge fed from 400 V line voltage?

  1. About 270 V
  2. About 360 V
  3. About 400 V
  4. About 540 V
Show answer & solution

Answer: (D) About 540 V

Vdc ≈ 1.35 × 400 = 540 V.

Question 14

What is the ripple frequency at the output of a three-phase six-pulse bridge rectifier on a 50 Hz supply?

  1. 50 Hz
  2. 100 Hz
  3. 150 Hz
  4. 300 Hz
Show answer & solution

Answer: (D) 300 Hz

The output has six pulses per cycle.

Question 15

How is a 12-pulse converter usually formed?

  1. By using a half-wave rectifier
  2. By connecting two six-pulse bridges fed from transformers with a 30° phase shift
  3. By adding capacitors only
  4. By using one single-phase bridge
Show answer & solution

Answer: (B) By connecting two six-pulse bridges fed from transformers with a 30° phase shift

12-pulse converters are used in HVDC and large drives to cut harmonics.

Question 16

Which harmonic currents are characteristic on the AC side of a six-pulse converter?

  1. 6k ± 1 harmonics such as the 5th, 7th, 11th and 13th
  2. Only even harmonics
  3. Only the 3rd harmonic
  4. No harmonics
Show answer & solution

Answer: (A) 6k ± 1 harmonics such as the 5th, 7th, 11th and 13th

Twelve-pulse converters cancel the 5th and 7th.

Question 17

What is the overlap (commutation) angle in a converter?

  1. The angle during which current transfers from one thyristor to the next because of source inductance
  2. The phase angle of the load
  3. The extinction angle
  4. The firing angle
Show answer & solution

Answer: (A) The angle during which current transfers from one thyristor to the next because of source inductance

Overlap reduces the average output voltage.

Question 18

What is the main purpose of a capacitor filter after a rectifier?

  1. To reduce DC voltage to zero
  2. To smooth the output and reduce ripple
  3. To convert DC to AC
  4. To increase ripple
Show answer & solution

Answer: (B) To smooth the output and reduce ripple

The capacitor charges near the peak and supplies current between peaks.

Question 19

What is the transformer utilisation factor (TUF) of a rectifier?

  1. The diode PIV
  2. The ratio of input to output voltage
  3. The ratio of DC output power to the transformer VA rating
  4. The ratio of ripple voltage to DC voltage
Show answer & solution

Answer: (C) The ratio of DC output power to the transformer VA rating

Bridge rectifiers have a better TUF than half-wave rectifiers.

Question 20

Why does a single-phase half-wave rectifier cause DC saturation of the supply transformer?

  1. It draws no current
  2. It has no diodes
  3. It uses a centre tap
  4. Current flows in only one direction in the secondary each cycle
Show answer & solution

Answer: (D) Current flows in only one direction in the secondary each cycle

The DC component magnetises the core.

Question 21

What is the effect of a freewheeling diode across the load of a single-phase controlled rectifier?

  1. It prevents negative output voltage and improves load current continuity
  2. It stops conduction
  3. It increases ripple
  4. It reverses output voltage
Show answer & solution

Answer: (A) It prevents negative output voltage and improves load current continuity

Inductive load energy freewheels through the diode.

Question 22

What is the input power factor of a phase-controlled rectifier at large firing angles?

  1. Zero always
  2. Low and lagging
  3. Leading
  4. Unity
Show answer & solution

Answer: (B) Low and lagging

Displacement factor is approximately cos α.

Question 23

What is the main advantage of a three-phase rectifier over a single-phase rectifier?

  1. More complex filter needed
  2. Lower power
  3. Higher ripple
  4. Lower ripple and higher output for large loads
Show answer & solution

Answer: (D) Lower ripple and higher output for large loads

Three-phase rectifiers are used for most industrial DC supplies.

Question 24

Which type of rectifier is used at the converter stations of the Matiari–Lahore HVDC line?

  1. Single-phase bridges
  2. Diode half-wave rectifiers
  3. Thyristor-based line-commutated converters
  4. Vacuum tube rectifiers
Show answer & solution

Answer: (C) Thyristor-based line-commutated converters

LCC-HVDC uses 12-pulse thyristor valves.

Question 25

What is the maximum output voltage of a fully controlled converter achieved at?

  1. A firing angle of 120°
  2. A firing angle of 90°
  3. A firing angle of 180°
  4. A firing angle of zero
Show answer & solution

Answer: (D) A firing angle of zero

The thyristors then behave like diodes.

Question 26

What is a dual converter?

  1. An inverter only
  2. A converter with two diodes
  3. Two fully controlled converters connected in anti-parallel to give four-quadrant operation
  4. A half-wave rectifier
Show answer & solution

Answer: (C) Two fully controlled converters connected in anti-parallel to give four-quadrant operation

It allows a DC motor to run and brake in both directions.

Question 27

Which circuit converts a sinusoidal input into a direct current output?

  1. Rectifier circuit
  2. Phase shifter
  3. Signal oscillator
  4. Voltage divider
Show answer & solution

Answer: (A) Rectifier circuit

Rectifiers use diodes or thyristors.

Question 28

What is the main purpose of an inductor (choke) in the DC output of a rectifier?

  1. To convert DC to AC
  2. To increase ripple
  3. To smooth the load current and reduce current ripple
  4. To block DC
Show answer & solution

Answer: (C) To smooth the load current and reduce current ripple

Large chokes give nearly constant current.

Question 29

What is the effect of increasing the firing angle on the output voltage of a controlled rectifier?

  1. It reduces the average output voltage
  2. It increases the output voltage
  3. It has no effect
  4. It reverses the frequency
Show answer & solution

Answer: (A) It reduces the average output voltage

Vdc ∝ cos α for a full converter with continuous current.

Question 30

What is the extinction angle of a thyristor converter operating as an inverter?

  1. The overlap angle
  2. The angle by which a thyristor current must fall to zero before its voltage becomes positive
  3. The power factor angle
  4. The firing angle
Show answer & solution

Answer: (B) The angle by which a thyristor current must fall to zero before its voltage becomes positive

A minimum margin is needed to avoid commutation failure.

Question 31

What is commutation failure in a line-commutated inverter?

  1. Failure of a thyristor to turn off before its voltage becomes forward biased, causing a short circuit
  2. A gate driver fault only
  3. Successful current transfer
  4. Normal operation
Show answer & solution

Answer: (A) Failure of a thyristor to turn off before its voltage becomes forward biased, causing a short circuit

It is a key concern at HVDC inverter stations.

Question 32

What is the ripple frequency at the output of a single-phase full-wave rectifier on a 50 Hz supply?

  1. 25 Hz
  2. 50 Hz
  3. 100 Hz
  4. 300 Hz
Show answer & solution

Answer: (C) 100 Hz

There are two pulses per input cycle.

Question 33

Why is a bridge rectifier preferred over a centre-tapped rectifier?

  1. It gives half-wave output
  2. It uses fewer diodes
  3. It has higher ripple
  4. It needs no centre-tapped transformer and diodes see lower peak inverse voltage
Show answer & solution

Answer: (D) It needs no centre-tapped transformer and diodes see lower peak inverse voltage

The bridge uses four diodes.

Question 34

What is the purpose of a voltage regulator after a rectifier and filter?

  1. To keep the DC output voltage constant despite input and load changes
  2. To act as a transformer
  3. To convert DC to AC
  4. To increase ripple
Show answer & solution

Answer: (A) To keep the DC output voltage constant despite input and load changes

Linear or switching regulators may be used.

Practice these 34 questions interactively →