Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Electronics: AC Controllers and Cycloconverters

Electrical Engineering · Power Electronics

26 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is an AC voltage controller?

  1. A rectifier
  2. A converter that changes frequency
  3. A DC–DC converter
  4. A converter that varies the RMS value of AC voltage at the same frequency
Show answer & solution

Answer: (D) A converter that varies the RMS value of AC voltage at the same frequency

It is used in heaters, lighting and soft starters.

Question 2

Which device is used in common ceiling fan regulators and light dimmers?

  1. Power diode bridge
  2. IGBT inverter
  3. TRIAC with phase-angle control
  4. Cycloconverter
Show answer & solution

Answer: (C) TRIAC with phase-angle control

The DIAC–TRIAC circuit varies the firing angle.

Question 3

What is integral cycle (on–off) control?

  1. Firing at different points in each cycle
  2. Connecting the load for a number of complete cycles and disconnecting it for others
  3. Changing frequency
  4. Converting AC to DC
Show answer & solution

Answer: (B) Connecting the load for a number of complete cycles and disconnecting it for others

It suits heating loads with long time constants.

Question 4

What is the main disadvantage of phase-angle control?

  1. It cannot vary power
  2. It produces pure sine waves
  3. It uses no switches
  4. It produces harmonics and lowers the power factor
Show answer & solution

Answer: (D) It produces harmonics and lowers the power factor

Integral cycle control reduces harmonics but causes flicker.

Question 5

What does a cycloconverter do?

  1. Converts AC at one frequency directly to AC at another, usually lower, frequency
  2. Converts AC to DC
  3. Converts DC to AC
  4. Steps up DC voltage
Show answer & solution

Answer: (A) Converts AC at one frequency directly to AC at another, usually lower, frequency

No intermediate DC link is used.

Question 6

In which application are cycloconverters typically used?

  1. Lighting dimmers
  2. Mobile phone chargers
  3. Large low-speed drives such as cement mills and ship propulsion
  4. Small fans
Show answer & solution

Answer: (C) Large low-speed drives such as cement mills and ship propulsion

They are suited to very high power at low frequency.

Question 7

What is a matrix converter?

  1. A transformer
  2. A DC–DC converter
  3. A direct AC–AC converter using an array of bidirectional switches without a DC link
  4. A diode rectifier
Show answer & solution

Answer: (C) A direct AC–AC converter using an array of bidirectional switches without a DC link

It can produce variable frequency and voltage.

Question 8

What power electronic arrangement is used in induction motor soft starters?

  1. Anti-parallel thyristors in each phase controlling voltage during starting
  2. A cycloconverter
  3. A diode bridge
  4. A boost converter
Show answer & solution

Answer: (A) Anti-parallel thyristors in each phase controlling voltage during starting

Soft starters reduce starting current and mechanical shock.

Question 9

What is a static transfer switch?

  1. A relay only
  2. A thyristor-based switch that transfers loads between two supplies in a few milliseconds
  3. A mechanical isolator
  4. A fuse
Show answer & solution

Answer: (B) A thyristor-based switch that transfers loads between two supplies in a few milliseconds

It is used for critical loads.

Question 10

What is a thyristor-controlled reactor (TCR)?

  1. A transformer
  2. A generator
  3. A capacitor switched by relays
  4. A reactor whose current is varied by thyristor phase control to absorb variable reactive power
Show answer & solution

Answer: (D) A reactor whose current is varied by thyristor phase control to absorb variable reactive power

TCRs are part of static VAR compensators.

Question 11

What is a thyristor-switched capacitor (TSC)?

  1. A capacitor bank switched in and out by thyristors at suitable instants
  2. A reactor
  3. An inverter
  4. A capacitor with no switch
Show answer & solution

Answer: (A) A capacitor bank switched in and out by thyristors at suitable instants

TSCs supply reactive power in steps without transients.

Question 12

What is the output frequency range of a three-phase cycloconverter on a 50 Hz supply typically?

  1. Exactly 50 Hz
  2. Zero only
  3. Up to about one-third of the supply frequency
  4. Many times the supply frequency
Show answer & solution

Answer: (C) Up to about one-third of the supply frequency

Higher output frequencies increase distortion.

Question 13

What happens to the RMS output voltage of an AC voltage controller as the firing angle increases?

  1. It stays constant
  2. It increases
  3. It doubles
  4. It decreases
Show answer & solution

Answer: (D) It decreases

Less of each half cycle reaches the load.

Question 14

Why is a TRIAC rarely used for high-power inductive loads?

  1. It cannot conduct
  2. It has limited dv/dt and current ratings and may fail to commutate
  3. It is too fast
  4. It is unidirectional
Show answer & solution

Answer: (B) It has limited dv/dt and current ratings and may fail to commutate

Anti-parallel SCRs are used at higher powers.

Question 15

What is the main application of AC voltage controllers in industry?

  1. Heating control, lighting control and motor soft starting
  2. Battery charging only
  3. Frequency conversion
  4. HVDC transmission
Show answer & solution

Answer: (A) Heating control, lighting control and motor soft starting

They are simple and cheap.

Question 16

What is a step-up cycloconverter?

  1. A normal low-frequency cycloconverter
  2. A cycloconverter producing output frequency higher than the input, which needs forced commutation
  3. A chopper
  4. A rectifier
Show answer & solution

Answer: (B) A cycloconverter producing output frequency higher than the input, which needs forced commutation

Most practical cycloconverters are step-down.

Question 17

What is the main difference between a cycloconverter and a VFD with a DC link?

  1. A cycloconverter converts AC to AC directly, while a VFD rectifies to DC and then inverts
  2. A cycloconverter uses a DC capacitor
  3. They are the same
  4. A VFD has no inverter
Show answer & solution

Answer: (A) A cycloconverter converts AC to AC directly, while a VFD rectifies to DC and then inverts

Cycloconverters avoid the DC link but produce more harmonics.

Question 18

What is the effect of phase-angle control on the supply current waveform?

  1. The current becomes pure DC
  2. The current becomes zero
  3. The current becomes non-sinusoidal with harmonic content
  4. The current becomes a perfect sine wave
Show answer & solution

Answer: (C) The current becomes non-sinusoidal with harmonic content

Harmonics increase as the firing angle increases.

Question 19

Why is integral cycle control not suitable for lamp dimming?

  1. It needs a DC supply
  2. It causes visible flicker because full cycles are switched on and off
  3. It cannot vary power
  4. It produces too few harmonics
Show answer & solution

Answer: (B) It causes visible flicker because full cycles are switched on and off

Phase-angle control gives smooth dimming.

Question 20

What is the purpose of a snubber circuit across a TRIAC used with an inductive load?

  1. To increase current
  2. To change frequency
  3. To increase dv/dt
  4. To limit dv/dt and help reliable commutation
Show answer & solution

Answer: (D) To limit dv/dt and help reliable commutation

Inductive loads cause voltage to rise rapidly when current falls to zero.

Question 21

What type of control is used in an electronic fan regulator compared with an older resistive regulator?

  1. Series resistance control
  2. Phase-angle control with a TRIAC, which wastes much less energy
  3. Frequency control with a cycloconverter
  4. DC chopper control
Show answer & solution

Answer: (B) Phase-angle control with a TRIAC, which wastes much less energy

Resistive regulators waste energy as heat.

Question 22

What is the firing angle in an AC voltage controller?

  1. The angle from the voltage zero crossing at which the thyristor or TRIAC is triggered
  2. The angle of the motor shaft
  3. The power factor angle of the supply
  4. The angle between two phases
Show answer & solution

Answer: (A) The angle from the voltage zero crossing at which the thyristor or TRIAC is triggered

A larger firing angle gives lower output voltage.

Question 23

Why are soft starters often bypassed by a contactor after the motor reaches full speed?

  1. To reverse rotation
  2. To reduce motor speed
  3. To increase starting current
  4. To eliminate thyristor conduction losses during normal running
Show answer & solution

Answer: (D) To eliminate thyristor conduction losses during normal running

The bypass contactor carries the running current.

Question 24

What is a three-phase AC voltage controller commonly used for besides soft starting?

  1. Converting AC to DC
  2. Charging mobile phones
  3. Controlling large heating loads and furnaces
  4. Driving stepper motors
Show answer & solution

Answer: (C) Controlling large heating loads and furnaces

Thyristor power controllers regulate heater power.

Question 25

Which component of a static VAR compensator supplies leading reactive power?

  1. Transformer tap changer
  2. Diode bridge
  3. Thyristor-controlled reactor only
  4. Thyristor-switched or fixed capacitors
Show answer & solution

Answer: (D) Thyristor-switched or fixed capacitors

The TCR absorbs reactive power; capacitors supply it.

Question 26

What is a solid-state relay (SSR)?

  1. A mechanical relay
  2. A semiconductor switch that controls AC loads without moving contacts
  3. A transformer
  4. A fuse
Show answer & solution

Answer: (B) A semiconductor switch that controls AC loads without moving contacts

SSRs often use TRIACs or anti-parallel SCRs with optical isolation.

Practice these 26 questions interactively →