Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Electronics: DC Choppers

Electrical Engineering · Power Electronics

31 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does a DC chopper do?

  1. Converts DC to AC
  2. Converts a fixed DC voltage into a variable DC voltage
  3. Changes AC frequency
  4. Converts AC to DC
Show answer & solution

Answer: (B) Converts a fixed DC voltage into a variable DC voltage

Choppers are DC–DC converters.

Question 2

What is the output voltage of an ideal buck (step-down) converter with input Vin and duty cycle D?

  1. D × Vin
  2. Vin × (1 − D)
  3. Vin/(1 − D)
  4. −D Vin/(1 − D)
Show answer & solution

Answer: (A) D × Vin

The output is always less than the input.

Question 3

What is the output voltage of an ideal boost (step-up) converter with input Vin and duty cycle D?

  1. D × Vin
  2. Vin/(1 − D)
  3. Vin × (1 − D)
  4. D/Vin
Show answer & solution

Answer: (B) Vin/(1 − D)

The output is always greater than the input.

Question 4

What is the output voltage of an ideal buck–boost converter?

  1. D Vin
  2. Vin/(1 − D)
  3. Vin(1 + D)
  4. −D Vin/(1 − D)
Show answer & solution

Answer: (D) −D Vin/(1 − D)

It can step up or down with inverted polarity.

Question 5

What is the output of an ideal buck converter with a 100 V input and a duty cycle of 0.4?

  1. 40 V
  2. 60 V
  3. 140 V
  4. 250 V
Show answer & solution

Answer: (A) 40 V

Vo = 0.4 × 100 = 40 V.

Question 6

What is the output of an ideal boost converter with a 12 V input and a duty cycle of 0.5?

  1. 6 V
  2. 12 V
  3. 24 V
  4. 36 V
Show answer & solution

Answer: (C) 24 V

Vo = 12/(1 − 0.5) = 24 V.

Question 7

How is duty cycle defined for a chopper?

  1. Frequency times voltage
  2. Output voltage divided by current
  3. Off-time divided by on-time
  4. On-time divided by total switching period
Show answer & solution

Answer: (D) On-time divided by total switching period

D = Ton/T.

Question 8

What is time ratio control in choppers?

  1. Controlling temperature
  2. Controlling input voltage
  3. Controlling output by varying the ratio of on-time to period
  4. Controlling load resistance
Show answer & solution

Answer: (C) Controlling output by varying the ratio of on-time to period

It can be done at constant or variable frequency.

Question 9

What is continuous conduction mode (CCM) in a DC–DC converter?

  1. Inductor current falls to zero each cycle
  2. Inductor current never falls to zero during the switching period
  3. The switch is always off
  4. The diode is never used
Show answer & solution

Answer: (B) Inductor current never falls to zero during the switching period

DCM changes the voltage conversion ratio.

Question 10

How can the output ripple of a buck converter be reduced?

  1. By lowering the switching frequency
  2. By reducing inductance
  3. By removing the capacitor
  4. By increasing the switching frequency, inductance or capacitance
Show answer & solution

Answer: (D) By increasing the switching frequency, inductance or capacitance

Larger filter elements smooth the output.

Question 11

Which converter is used to recover braking energy from a DC traction motor back to the supply?

  1. Boost (step-up) chopper operation
  2. Buck chopper only
  3. Cycloconverter
  4. Half-wave rectifier
Show answer & solution

Answer: (A) Boost (step-up) chopper operation

During regeneration, the motor emf is boosted to the supply level.

Question 12

Which chopper class can operate in all four quadrants of voltage and current?

  1. Class B chopper
  2. Class A chopper
  3. Class E chopper
  4. Class C chopper
Show answer & solution

Answer: (C) Class E chopper

Class E is used for reversible regenerative DC drives.

Question 13

What is the main advantage of switch-mode power supplies over linear power supplies?

  1. Larger transformers
  2. Higher efficiency and smaller size
  3. No switching noise
  4. Lower efficiency
Show answer & solution

Answer: (B) Higher efficiency and smaller size

Switching at high frequency allows small magnetics.

Question 14

Which isolated converter stores energy in a coupled inductor during the switch on-time and releases it during off-time?

  1. Buck converter
  2. Forward converter
  3. Boost converter
  4. Flyback converter
Show answer & solution

Answer: (D) Flyback converter

Flyback converters are common in low-power chargers.

Question 15

What is a forward converter?

  1. A rectifier
  2. An isolated buck-derived converter that transfers energy through a transformer during the switch on-time
  3. An inverter
  4. A non-isolated boost converter
Show answer & solution

Answer: (B) An isolated buck-derived converter that transfers energy through a transformer during the switch on-time

It needs a core reset mechanism.

Question 16

Why do switching losses increase with switching frequency?

  1. Current becomes zero
  2. Conduction time increases
  3. Energy is lost at each turn-on and turn-off transition
  4. Voltage falls
Show answer & solution

Answer: (C) Energy is lost at each turn-on and turn-off transition

Soft-switching techniques reduce these losses.

Question 17

What is zero-voltage switching (ZVS)?

  1. Turning a switch on when the voltage across it is zero, reducing switching loss
  2. Switching with zero frequency
  3. Switching with no gate signal
  4. Switching only at zero current
Show answer & solution

Answer: (A) Turning a switch on when the voltage across it is zero, reducing switching loss

Resonant converters use ZVS or ZCS.

Question 18

What is the role of the freewheeling diode in a buck converter?

  1. To increase output voltage
  2. To turn on the switch
  3. To carry inductor current when the switch is off
  4. To block input voltage
Show answer & solution

Answer: (C) To carry inductor current when the switch is off

It allows continuous current flow to the load.

Question 19

Which converter topology is commonly used for power factor correction at the input of SMPS and chargers?

  1. Boost converter
  2. Buck converter
  3. Flyback only
  4. Cycloconverter
Show answer & solution

Answer: (A) Boost converter

A boost PFC makes input current follow the voltage waveform.

Question 20

What is the function of a maximum power point tracker in a solar charge controller?

  1. To increase module temperature
  2. To disconnect every parallel string
  3. To reduce solar irradiance
  4. To adjust the DC–DC converter so the panel operates at its maximum power point
Show answer & solution

Answer: (D) To adjust the DC–DC converter so the panel operates at its maximum power point

MPPT controllers increase energy harvest.

Question 21

What is a Cuk converter?

  1. A rectifier
  2. A DC–DC converter using capacitive energy transfer that can step up or down with inverted output and low ripple currents
  3. An AC voltage controller
  4. A cycloconverter
Show answer & solution

Answer: (B) A DC–DC converter using capacitive energy transfer that can step up or down with inverted output and low ripple currents

It has inductors at both input and output.

Question 22

What happens to the output voltage of an ideal boost converter as the duty cycle approaches 1?

  1. It falls to zero
  2. It rises towards very high values, limited in practice by losses
  3. It becomes negative
  4. It equals the input
Show answer & solution

Answer: (B) It rises towards very high values, limited in practice by losses

Real converters have a maximum practical duty cycle.

Question 23

Why are DC–DC converters essential in electric vehicles?

  1. To supply low-voltage auxiliaries from the high-voltage battery and interface batteries with motor drives
  2. To increase frequency
  3. To convert AC to AC
  4. To charge only AC loads
Show answer & solution

Answer: (A) To supply low-voltage auxiliaries from the high-voltage battery and interface batteries with motor drives

EVs use several DC–DC stages.

Question 24

What is the purpose of the output capacitor in a buck converter?

  1. To smooth output voltage ripple
  2. To increase ripple
  3. To store input energy only
  4. To switch current
Show answer & solution

Answer: (A) To smooth output voltage ripple

Its ESR affects ripple performance.

Question 25

What is the main function of the inductor in a boost converter?

  1. To provide isolation
  2. To block DC
  3. To store energy during the on-time and release it to the output during the off-time
  4. To filter only high frequencies at the output
Show answer & solution

Answer: (C) To store energy during the on-time and release it to the output during the off-time

The stored energy adds to the input voltage.

Question 26

What is the advantage of synchronous rectification in low-voltage DC–DC converters?

  1. It increases losses
  2. Replacing diodes with MOSFETs reduces conduction losses
  3. It removes the need for switching
  4. It increases diode drop
Show answer & solution

Answer: (B) Replacing diodes with MOSFETs reduces conduction losses

It is widely used in computer power supplies.

Question 27

What is a DC–DC converter called if it has a transformer between input and output?

  1. Non-isolated converter
  2. Linear regulator
  3. Isolated converter
  4. Rectifier
Show answer & solution

Answer: (C) Isolated converter

Isolation provides safety and voltage scaling.

Question 28

Why are higher switching frequencies used in modern DC–DC converters?

  1. To increase size
  2. To reduce efficiency deliberately
  3. To lower power density
  4. To reduce the size of inductors, capacitors and transformers
Show answer & solution

Answer: (D) To reduce the size of inductors, capacitors and transformers

Losses and EMI rise with frequency, so a balance is chosen.

Question 29

What is the duty cycle needed for a buck converter to produce 5 V from 20 V?

  1. 0.25
  2. 0.5
  3. 0.75
  4. 4
Show answer & solution

Answer: (A) 0.25

D = Vo/Vin = 5/20.

Question 30

What is the main purpose of current-mode control in DC–DC converters?

  1. To remove feedback
  2. To control inductor current directly for faster response and built-in current limiting
  3. To increase ripple
  4. To fix duty cycle
Show answer & solution

Answer: (B) To control inductor current directly for faster response and built-in current limiting

Peak current mode control is common in SMPS ICs.

Question 31

What is electromagnetic interference (EMI) in switching converters caused by?

  1. Large heat sinks
  2. Fast changes of voltage and current during switching
  3. Constant DC current
  4. Low frequency only
Show answer & solution

Answer: (B) Fast changes of voltage and current during switching

Filters, layout and shielding reduce EMI.

Practice these 31 questions interactively →