Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Electronics: Drives and Applications

Electrical Engineering · Power Electronics

32 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What are the main stages of a typical variable frequency drive (VFD)?

  1. Inverter, rectifier and transformer only
  2. Motor and generator
  3. Rectifier, DC link and inverter
  4. Cycloconverter only
Show answer & solution

Answer: (C) Rectifier, DC link and inverter

The inverter produces variable voltage and frequency.

Question 2

Why is the V/f ratio kept constant in scalar control of induction motors?

  1. To keep current zero
  2. To increase flux at low speed
  3. To reduce slip to zero
  4. To keep magnetic flux nearly constant as speed changes
Show answer & solution

Answer: (D) To keep magnetic flux nearly constant as speed changes

At low speeds a voltage boost compensates for stator resistance.

Question 3

What is the main advantage of vector (field-oriented) control of induction motors?

  1. It needs no inverter
  2. It needs no current measurement
  3. It works only at fixed speed
  4. Independent control of torque and flux, giving dynamic performance like a DC motor
Show answer & solution

Answer: (D) Independent control of torque and flux, giving dynamic performance like a DC motor

It is used in high-performance drives.

Question 4

What is direct torque control (DTC)?

  1. A control method that selects inverter switching states directly to control torque and flux
  2. A scalar V/f method
  3. A method using rotor resistance
  4. A mechanical brake
Show answer & solution

Answer: (A) A control method that selects inverter switching states directly to control torque and flux

DTC gives very fast torque response.

Question 5

How is a DC motor commonly supplied in a variable speed drive from an AC supply?

  1. Through a transformer only
  2. Through a diode bridge only
  3. Through a phase-controlled rectifier
  4. Through a cycloconverter
Show answer & solution

Answer: (C) Through a phase-controlled rectifier

Choppers are used when the supply is DC.

Question 6

Why is a braking resistor (brake chopper) used in VFDs?

  1. To start the motor
  2. To dissipate regenerated energy that raises the DC link voltage during braking
  3. To improve power factor
  4. To filter harmonics
Show answer & solution

Answer: (B) To dissipate regenerated energy that raises the DC link voltage during braking

Without it, the drive may trip on overvoltage.

Question 7

How can harmonics injected by a VFD into the supply be reduced?

  1. Using longer cables only
  2. Increasing the motor size
  3. Using DC chokes, line reactors, 12- or 18-pulse rectifiers, active front ends or filters
  4. Removing the DC link
Show answer & solution

Answer: (C) Using DC chokes, line reactors, 12- or 18-pulse rectifiers, active front ends or filters

Harmonics cause heating and interference.

Question 8

According to the affinity laws, how does the power of a centrifugal fan or pump vary with speed?

  1. With the square of speed
  2. With the cube of speed
  3. Inversely with speed
  4. Directly with speed
Show answer & solution

Answer: (B) With the cube of speed

This is why VFDs save large amounts of energy.

Question 9

What percentage of full-speed power does a centrifugal pump need at 80% speed?

  1. 40%
  2. About 51%
  3. 64%
  4. 80%
Show answer & solution

Answer: (B) About 51%

0.8³ ≈ 0.51.

Question 10

Which power electronic converter is used in HVDC stations at both ends of a line?

  1. Rectifier at the sending end and inverter at the receiving end
  2. Choppers at both ends
  3. Diode rectifiers only
  4. Cycloconverters only
Show answer & solution

Answer: (A) Rectifier at the sending end and inverter at the receiving end

Power flow can be reversed by changing the control.

Question 11

What is the main purpose of power factor correction (PFC) circuits in switch-mode power supplies?

  1. To increase harmonics
  2. To reduce efficiency
  3. To store energy for years
  4. To make input current sinusoidal and in phase with voltage
Show answer & solution

Answer: (D) To make input current sinusoidal and in phase with voltage

PFC is required by standards such as IEC 61000-3-2.

Question 12

What is the purpose of an active front end (AFE) in a drive?

  1. To replace the motor
  2. To increase harmonics
  3. To remove the DC link
  4. To draw nearly sinusoidal current and allow regeneration to the supply
Show answer & solution

Answer: (D) To draw nearly sinusoidal current and allow regeneration to the supply

AFEs use IGBT rectifiers instead of diodes.

Question 13

What problem can long cables between a PWM inverter and motor cause?

  1. Voltage reflections that overstress motor insulation
  2. Lower motor voltage only
  3. No effect
  4. Lower switching frequency
Show answer & solution

Answer: (A) Voltage reflections that overstress motor insulation

dv/dt filters or sine filters protect the motor.

Question 14

What causes bearing currents in inverter-fed motors?

  1. Low supply frequency
  2. DC field windings
  3. Common-mode voltages from fast switching coupling through motor capacitances
  4. Mechanical overload
Show answer & solution

Answer: (C) Common-mode voltages from fast switching coupling through motor capacitances

Insulated bearings and shaft grounding reduce damage.

Question 15

In which application is power electronics used to charge batteries from a solar panel?

  1. Induction motor starter
  2. Cycloconverter
  3. Solar charge controller
  4. Fan regulator
Show answer & solution

Answer: (C) Solar charge controller

PWM or MPPT controllers protect the battery.

Question 16

What is the role of power electronics in electronic ballasts for lamps?

  1. To store energy
  2. To increase lamp heating
  3. To convert DC to low-frequency AC
  4. To convert mains to high-frequency AC for efficient, flicker-free lighting
Show answer & solution

Answer: (D) To convert mains to high-frequency AC for efficient, flicker-free lighting

LED drivers are a modern example.

Question 17

What is the main advantage of a VFD for a pump in a water supply scheme?

  1. Energy savings by matching speed to demand instead of throttling valves
  2. Need for larger motors
  3. Higher energy use
  4. More noise
Show answer & solution

Answer: (A) Energy savings by matching speed to demand instead of throttling valves

Throttling wastes energy while a VFD reduces it.

Question 18

What is regenerative braking in an electric vehicle?

  1. Using friction brakes only
  2. Using the motor as a generator through the inverter to charge the battery while slowing down
  3. Disconnecting the motor
  4. Increasing speed
Show answer & solution

Answer: (B) Using the motor as a generator through the inverter to charge the battery while slowing down

Regeneration extends driving range.

Question 19

What is the function of an uninterruptible power supply (UPS) in hospitals and data centres?

  1. To generate power from fuel
  2. To reduce voltage
  3. To provide continuous power to critical loads during supply interruptions
  4. To increase load demand
Show answer & solution

Answer: (C) To provide continuous power to critical loads during supply interruptions

UPS systems combine rectifiers, batteries and inverters.

Question 20

Which converter is used in modern inverter air conditioners to vary compressor speed?

  1. A rectifier followed by a PWM inverter driving a BLDC or PMSM compressor motor
  2. A diode bridge only
  3. A cycloconverter
  4. A fan regulator
Show answer & solution

Answer: (A) A rectifier followed by a PWM inverter driving a BLDC or PMSM compressor motor

Speed control saves energy and improves comfort.

Question 21

What is the effect of harmonics from power electronic loads on neutral conductors?

  1. They cancel completely
  2. They have no effect
  3. They reduce neutral current to zero
  4. Triplen harmonics add in the neutral and can overload it
Show answer & solution

Answer: (D) Triplen harmonics add in the neutral and can overload it

Neutrals may need to be oversized in buildings with many electronic loads.

Question 22

What is the main purpose of an induction heating power supply?

  1. To control fans
  2. To produce high-frequency AC current in a coil that heats metal by eddy currents
  3. To charge batteries
  4. To drive DC motors
Show answer & solution

Answer: (B) To produce high-frequency AC current in a coil that heats metal by eddy currents

It is used for melting, hardening and brazing.

Question 23

What is a four-quadrant drive?

  1. A drive that can motor and brake in both forward and reverse directions
  2. A drive with four switches only
  3. A drive for single-phase motors only
  4. A drive for four motors
Show answer & solution

Answer: (A) A drive that can motor and brake in both forward and reverse directions

Cranes, lifts and rolling mills need four-quadrant operation.

Question 24

What is slip power recovery in wound-rotor induction motor drives?

  1. Using a DC motor
  2. Increasing slip
  3. Recovering rotor slip power through converters and returning it to the supply
  4. Wasting slip power in resistors
Show answer & solution

Answer: (C) Recovering rotor slip power through converters and returning it to the supply

The static Kramer and Scherbius drives use this principle.

Question 25

What is a doubly fed induction generator (DFIG) used for?

  1. Battery chargers
  2. Lighting circuits
  3. Small household fans
  4. Variable-speed wind turbines with a partially rated rotor-side converter
Show answer & solution

Answer: (D) Variable-speed wind turbines with a partially rated rotor-side converter

The converter handles only part of the total power.

Question 26

Why are VFDs widely used in water pumping and HVAC systems in Pakistan's industries and buildings?

  1. They need bigger motors
  2. They increase electricity bills
  3. They reduce reliability
  4. They cut energy use by matching motor speed to actual demand
Show answer & solution

Answer: (D) They cut energy use by matching motor speed to actual demand

Energy savings often recover the drive cost quickly.

Question 27

What is the purpose of the DC link choke in a VFD?

  1. To reverse rotation
  2. To start the motor
  3. To reduce input current harmonics and smooth DC link current
  4. To increase harmonics
Show answer & solution

Answer: (C) To reduce input current harmonics and smooth DC link current

It improves the input power factor.

Question 28

What is a servo drive?

  1. A fuse
  2. An amplifier that controls a servo motor's position, speed or torque using feedback
  3. A transformer
  4. A fixed-speed starter
Show answer & solution

Answer: (B) An amplifier that controls a servo motor's position, speed or torque using feedback

Servo drives are used in robots and CNC machines.

Question 29

Which power electronic system connects offshore wind farms or asynchronous grids efficiently?

  1. VSC-based HVDC
  2. Cycloconverter
  3. Diode half-wave rectifier
  4. Fan regulator
Show answer & solution

Answer: (A) VSC-based HVDC

VSC-HVDC can control active and reactive power independently.

Question 30

What is a static frequency converter used for in power plants?

  1. Starting large gas turbines by running the generator as a motor
  2. Measuring speed
  3. Charging batteries
  4. Lighting
Show answer & solution

Answer: (A) Starting large gas turbines by running the generator as a motor

It supplies variable frequency to accelerate the unit.

Question 31

What is the function of a battery management system (BMS) in electric vehicles and storage systems?

  1. To drive the motor
  2. To monitor and protect battery cells for voltage, current and temperature
  3. To charge from the grid only
  4. To act as an inverter
Show answer & solution

Answer: (B) To monitor and protect battery cells for voltage, current and temperature

It balances cells and prevents unsafe operation.

Question 32

What is the main concern when many single-phase rectifier loads such as computers are supplied in a building?

  1. Zero distortion
  2. Leading power factor
  3. Too little current
  4. High third-harmonic currents and neutral overloading
Show answer & solution

Answer: (D) High third-harmonic currents and neutral overloading

Harmonic studies help size neutrals and transformers.

Practice these 32 questions interactively →