Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Electronics: Power Devices

Electrical Engineering · Power Electronics

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

How many semiconductor layers and junctions does a thyristor (SCR) have?

  1. Five layers and four junctions
  2. Two layers and one junction
  3. Three layers and two junctions
  4. Four layers and three junctions
Show answer & solution

Answer: (D) Four layers and three junctions

It has a PNPN structure with anode, cathode and gate.

Question 2

What are the three terminals of an SCR?

  1. Anode, cathode and base
  2. Anode, cathode and gate
  3. Drain, source and gate
  4. Collector, emitter and base
Show answer & solution

Answer: (B) Anode, cathode and gate

A small gate current turns the SCR on.

Question 3

What is the latching current of an SCR?

  1. The current at which it turns off
  2. The maximum gate current
  3. The minimum anode current needed to keep it on immediately after the gate pulse is removed
  4. The leakage current
Show answer & solution

Answer: (C) The minimum anode current needed to keep it on immediately after the gate pulse is removed

Latching current is greater than holding current.

Question 4

What is the holding current of an SCR?

  1. The minimum anode current below which a conducting SCR turns off
  2. The gate current
  3. The current needed to turn it on
  4. The maximum anode current
Show answer & solution

Answer: (A) The minimum anode current below which a conducting SCR turns off

An SCR turns off when its current falls below holding current.

Question 5

Which is the most common and reliable method of turning on an SCR?

  1. Raising its temperature
  2. Exposing it to light in all cases
  3. Applying a positive gate pulse
  4. Applying a high dv/dt
Show answer & solution

Answer: (C) Applying a positive gate pulse

Forward breakover and dv/dt turn-on are usually undesirable.

Question 6

Why is an RC snubber connected across an SCR?

  1. To increase current
  2. To limit the rate of rise of voltage (dv/dt) and prevent false turn-on
  3. To increase dv/dt
  4. To turn the SCR off
Show answer & solution

Answer: (B) To limit the rate of rise of voltage (dv/dt) and prevent false turn-on

Snubbers also absorb switching transients.

Question 7

Why is a small inductor connected in series with an SCR?

  1. To limit the rate of rise of current (di/dt) at turn-on
  2. To reduce holding current
  3. To store energy for the gate
  4. To increase di/dt
Show answer & solution

Answer: (A) To limit the rate of rise of current (di/dt) at turn-on

High di/dt can cause local hot spots and damage.

Question 8

What is commutation of a thyristor?

  1. The process of turning it on
  2. The process of triggering the gate
  3. The process of cooling it
  4. The process of turning it off by reducing its current below holding current
Show answer & solution

Answer: (D) The process of turning it off by reducing its current below holding current

Natural (line) commutation occurs in AC circuits; forced commutation in DC circuits.

Question 9

How is a gate turn-off thyristor (GTO) turned off?

  1. By removing the load only
  2. By applying a negative gate current pulse
  3. By applying a positive gate pulse
  4. By heating it
Show answer & solution

Answer: (B) By applying a negative gate current pulse

GTOs do not need external commutation circuits.

Question 10

Which device conducts in both directions and is used in fan regulators and light dimmers?

  1. TRIAC
  2. GTO
  3. SCR
  4. Power diode
Show answer & solution

Answer: (A) TRIAC

A TRIAC behaves like two SCRs in anti-parallel with a common gate.

Question 11

Which device is commonly used to trigger a TRIAC?

  1. Power MOSFET
  2. Zener diode only
  3. DIAC
  4. IGBT
Show answer & solution

Answer: (C) DIAC

The DIAC breaks over at a fixed voltage to give a sharp trigger pulse.

Question 12

Which device is voltage-controlled and has the fastest switching among common power devices?

  1. Power BJT
  2. GTO
  3. SCR
  4. Power MOSFET
Show answer & solution

Answer: (D) Power MOSFET

MOSFETs suit high-frequency switching at low to medium voltages.

Question 13

Why can power MOSFETs be connected in parallel easily?

  1. Their resistance falls with temperature
  2. Their on-resistance has a positive temperature coefficient, so current shares evenly
  3. They are current-controlled
  4. They have no resistance
Show answer & solution

Answer: (B) Their on-resistance has a positive temperature coefficient, so current shares evenly

A hotter device carries less current.

Question 14

Which power device combines the voltage-controlled input of a MOSFET with the low conduction loss of a BJT?

  1. SCR
  2. UJT
  3. DIAC
  4. IGBT
Show answer & solution

Answer: (D) IGBT

IGBTs are the most widely used switches in medium and high power inverters.

Question 15

How is a power BJT controlled?

  1. By gate voltage
  2. By light
  3. By base current
  4. By temperature
Show answer & solution

Answer: (C) By base current

BJTs need continuous base drive while conducting.

Question 16

What is a key advantage of silicon carbide (SiC) and gallium nitride (GaN) devices?

  1. Higher voltage, temperature and switching frequency with lower losses
  2. Lower breakdown voltage
  3. Slower switching
  4. Higher conduction loss
Show answer & solution

Answer: (A) Higher voltage, temperature and switching frequency with lower losses

Wide-bandgap devices allow smaller, more efficient converters.

Question 17

What is the function of a freewheeling diode in a converter with an inductive load?

  1. To turn on the switch
  2. To block all current
  3. To increase voltage spikes
  4. To provide a path for load current when the switch turns off
Show answer & solution

Answer: (D) To provide a path for load current when the switch turns off

It prevents high voltages from L di/dt.

Question 18

Which diode has a very low forward voltage drop and fast switching, but low reverse voltage rating?

  1. Schottky diode
  2. Rectifier diode
  3. Zener diode
  4. Avalanche diode only
Show answer & solution

Answer: (A) Schottky diode

It uses a metal–semiconductor junction.

Question 19

What is a fast recovery diode used for?

  1. Light emission
  2. Low-frequency rectifiers only
  3. High-frequency switching circuits where short reverse recovery time is needed
  4. Voltage regulation
Show answer & solution

Answer: (C) High-frequency switching circuits where short reverse recovery time is needed

Reverse recovery causes switching loss.

Question 20

Which device is often used in relaxation oscillators to generate triggering pulses for SCRs?

  1. GTO
  2. Unijunction transistor (UJT)
  3. IGBT
  4. TRIAC
Show answer & solution

Answer: (B) Unijunction transistor (UJT)

The UJT's intrinsic stand-off ratio sets its firing voltage.

Question 21

What does the safe operating area (SOA) of a power device define?

  1. The limits of voltage, current and power within which it can operate safely
  2. The heat sink size
  3. The gate voltage only
  4. The physical area of the device
Show answer & solution

Answer: (A) The limits of voltage, current and power within which it can operate safely

Operating outside the SOA can destroy the device.

Question 22

Why are heat sinks used with power semiconductor devices?

  1. To increase voltage
  2. To remove heat and keep junction temperature within limits
  3. To store charge
  4. To increase current gain
Show answer & solution

Answer: (B) To remove heat and keep junction temperature within limits

Junction temperature limits device rating.

Question 23

Which type of thyristor is triggered by light and used in HVDC valves?

  1. DIAC
  2. GTO
  3. Light-activated (light-triggered) thyristor
  4. TRIAC
Show answer & solution

Answer: (C) Light-activated (light-triggered) thyristor

Light triggering gives isolation at very high voltages.

Question 24

What is the turn-off time of a thyristor?

  1. The time to turn it on
  2. The time the gate pulse lasts
  3. The time the load runs
  4. The minimum time after current reaches zero before forward voltage can be reapplied without turn-on
Show answer & solution

Answer: (D) The minimum time after current reaches zero before forward voltage can be reapplied without turn-on

The circuit must provide reverse bias for at least this time.

Question 25

What is the forward breakover voltage of an SCR?

  1. The reverse voltage it can block
  2. The voltage across it while conducting
  3. The forward voltage at which it turns on without gate current
  4. The gate voltage
Show answer & solution

Answer: (C) The forward voltage at which it turns on without gate current

Gate current reduces the breakover voltage.

Question 26

What is the typical forward voltage drop of a conducting thyristor?

  1. About 0.01 V
  2. About 1 to 2 V
  3. About 20 V
  4. About 100 V
Show answer & solution

Answer: (B) About 1 to 2 V

Conduction loss is roughly the drop times average current.

Question 27

Which power device is preferred for very high power, low-frequency applications such as HVDC and large drives?

  1. Schottky diode
  2. Power MOSFET
  3. Small-signal BJT
  4. Thyristor
Show answer & solution

Answer: (D) Thyristor

Thyristors have the highest voltage and current ratings.

Question 28

What is the main disadvantage of an SCR compared with an IGBT?

  1. It cannot be turned off by its gate signal
  2. It cannot be turned on
  3. It has lower ratings
  4. It cannot block voltage
Show answer & solution

Answer: (A) It cannot be turned off by its gate signal

SCRs need current commutation.

Question 29

What is an IGCT?

  1. An integrated gate-commutated thyristor combining GTO structure with an integrated gate driver
  2. An IGBT for small loads
  3. A type of diode
  4. A capacitor
Show answer & solution

Answer: (A) An integrated gate-commutated thyristor combining GTO structure with an integrated gate driver

IGCTs are used in medium-voltage drives.

Question 30

What does reverse recovery time of a diode mean?

  1. The time for forward voltage to rise
  2. The time to turn on
  3. The diode's life
  4. The time taken for a diode to stop conducting in reverse after forward current is removed
Show answer & solution

Answer: (D) The time taken for a diode to stop conducting in reverse after forward current is removed

Long recovery causes losses and noise.

Question 31

Which device is a three-terminal, voltage-controlled switch with insulated gate, drain and source terminals?

  1. SCR
  2. MOSFET
  3. BJT
  4. DIAC
Show answer & solution

Answer: (B) MOSFET

The gate draws almost no steady current.

Question 32

Which device is best suited for switching at hundreds of kilohertz in switch-mode power supplies?

  1. GTO
  2. Line-frequency thyristor
  3. Power MOSFET or GaN transistor
  4. SCR
Show answer & solution

Answer: (C) Power MOSFET or GaN transistor

Fast switching allows small magnetic components.

Question 33

What is the main function of an optocoupler in gate drive circuits?

  1. To store energy
  2. To limit di/dt
  3. To provide electrical isolation between control circuits and power devices
  4. To amplify power
Show answer & solution

Answer: (C) To provide electrical isolation between control circuits and power devices

Isolation protects low-voltage control electronics.

Question 34

What is the typical gate threshold voltage range of a power MOSFET?

  1. About 0.1 V
  2. About 2 to 4 V
  3. About 50 V
  4. About 500 V
Show answer & solution

Answer: (B) About 2 to 4 V

Gate drives usually apply 10–15 V for full enhancement.

Question 35

What is meant by the conduction loss of a power switch?

  1. Power lost while the device is conducting, due to its on-state voltage or resistance
  2. Power lost in the heat sink
  3. Power lost in the gate driver
  4. Power lost at turn-on only
Show answer & solution

Answer: (A) Power lost while the device is conducting, due to its on-state voltage or resistance

For a MOSFET it is I²RDS(on).

Question 36

Which device would be chosen for a 1 MW, 3.3 kV medium-voltage drive?

  1. Schottky diodes
  2. Small signal transistors
  3. TRIACs
  4. High-voltage IGBT or IGCT modules
Show answer & solution

Answer: (D) High-voltage IGBT or IGCT modules

Medium-voltage drives often use multilevel inverters.

Practice these 36 questions interactively →