Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Electronics: Inverters

Electrical Engineering · Power Electronics

32 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does an inverter do?

  1. Changes AC frequency directly
  2. Converts DC power into AC power
  3. Changes DC voltage level only
  4. Converts AC to DC
Show answer & solution

Answer: (B) Converts DC power into AC power

Inverters are used in UPS, drives and solar systems.

Question 2

Which device converts a PV array's direct current output into alternating current?

  1. DC combiner
  2. Charge controller
  3. Power inverter
  4. Blocking diode
Show answer & solution

Answer: (C) Power inverter

Grid-tie inverters also synchronise with the grid.

Question 3

What is the difference between a voltage source inverter (VSI) and a current source inverter (CSI)?

  1. They are identical
  2. A VSI has no switches
  3. A CSI needs no DC source
  4. A VSI has a stiff DC voltage input with a capacitor; a CSI has a stiff DC current input with an inductor
Show answer & solution

Answer: (D) A VSI has a stiff DC voltage input with a capacitor; a CSI has a stiff DC current input with an inductor

VSIs are far more common in modern drives.

Question 4

What is the peak output voltage of a single-phase half-bridge inverter with DC supply Vdc?

  1. Vdc/2
  2. Vdc
  3. 2Vdc
  4. Vdc/4
Show answer & solution

Answer: (A) Vdc/2

A full-bridge gives a peak of Vdc.

Question 5

Why is a square-wave inverter output unsuitable for many loads?

  1. It is pure DC
  2. It contains large low-order harmonics
  3. It is a perfect sine wave
  4. It has no fundamental
Show answer & solution

Answer: (B) It contains large low-order harmonics

Harmonics cause heating and noise in motors and transformers.

Question 6

What is the main purpose of pulse width modulation (PWM) in inverters?

  1. To increase harmonics
  2. To reduce frequency to zero
  3. To control output voltage and reduce low-order harmonics
  4. To convert AC to DC
Show answer & solution

Answer: (C) To control output voltage and reduce low-order harmonics

Harmonics are moved to higher frequencies that are easier to filter.

Question 7

In sinusoidal PWM, what determines the inverter output frequency?

  1. The frequency of the sinusoidal reference (modulating) signal
  2. The DC voltage
  3. The load
  4. The carrier frequency
Show answer & solution

Answer: (A) The frequency of the sinusoidal reference (modulating) signal

The carrier frequency sets the switching frequency.

Question 8

What is the modulation index in sinusoidal PWM?

  1. The ratio of carrier to reference frequency
  2. The ratio of the reference signal peak to the carrier signal peak
  3. The DC voltage
  4. The switching loss
Show answer & solution

Answer: (B) The ratio of the reference signal peak to the carrier signal peak

Output voltage rises with modulation index.

Question 9

Why is dead time used between switching the upper and lower switches of an inverter leg?

  1. To increase output voltage
  2. To reduce frequency
  3. To increase harmonics deliberately
  4. To prevent both switches conducting together and short-circuiting the DC bus (shoot-through)
Show answer & solution

Answer: (D) To prevent both switches conducting together and short-circuiting the DC bus (shoot-through)

Dead time slightly distorts the output.

Question 10

What is an online (double conversion) UPS?

  1. A UPS that switches only on supply failure
  2. A voltage stabiliser
  3. A UPS in which the load is always fed through the inverter from the rectifier and battery
  4. A generator
Show answer & solution

Answer: (C) A UPS in which the load is always fed through the inverter from the rectifier and battery

It gives zero transfer time and clean output.

Question 11

What is an offline (standby) UPS?

  1. A UPS that always uses the inverter
  2. A transformer
  3. A diesel generator
  4. A UPS that supplies the load directly from mains and switches to the inverter only on power failure
Show answer & solution

Answer: (D) A UPS that supplies the load directly from mains and switches to the inverter only on power failure

It is cheaper but has a short transfer time.

Question 12

What is anti-islanding protection in a grid-tie inverter?

  1. A function that stops the inverter feeding power when the grid supply is lost
  2. A function that increases output
  3. A battery charger
  4. A lightning arrester
Show answer & solution

Answer: (A) A function that stops the inverter feeding power when the grid supply is lost

It protects line workers during outages.

Question 13

Why are multilevel inverters used in medium-voltage drives?

  1. They have higher harmonics
  2. They produce lower harmonics and lower voltage stress on each switch
  3. They produce square waves only
  4. They need no switches
Show answer & solution

Answer: (B) They produce lower harmonics and lower voltage stress on each switch

Neutral-point clamped inverters are a common type.

Question 14

What does total harmonic distortion (THD) measure?

  1. The power factor only
  2. The ratio of RMS harmonic content to the fundamental component
  3. The DC voltage
  4. The switching frequency
Show answer & solution

Answer: (B) The ratio of RMS harmonic content to the fundamental component

Low THD is important for grid-connected inverters.

Question 15

Why is an LC filter used at the output of an inverter?

  1. To increase harmonics
  2. To store DC energy only
  3. To convert AC to DC
  4. To filter switching harmonics and give a near-sinusoidal output
Show answer & solution

Answer: (D) To filter switching harmonics and give a near-sinusoidal output

LCL filters are common in grid-tie inverters.

Question 16

In a three-phase six-step inverter with 180° conduction, how many switches conduct at any time?

  1. Three
  2. Two
  3. Six
  4. One
Show answer & solution

Answer: (A) Three

In 120° conduction mode, two switches conduct at a time.

Question 17

What is the main advantage of space vector PWM over sinusoidal PWM?

  1. No switching
  2. Higher harmonics
  3. Better DC bus voltage utilisation, about 15% higher output voltage
  4. Lower efficiency
Show answer & solution

Answer: (C) Better DC bus voltage utilisation, about 15% higher output voltage

It is widely used in digital motor drives.

Question 18

Which inverter type is commonly used for induction heating?

  1. Cycloconverter
  2. Resonant (series or parallel) inverter
  3. Square-wave inverter at 50 Hz
  4. Diode rectifier
Show answer & solution

Answer: (B) Resonant (series or parallel) inverter

High-frequency resonant inverters heat metals efficiently.

Question 19

What is the main difference between a pure sine wave inverter and a modified sine wave inverter?

  1. A pure sine inverter outputs DC
  2. They are identical
  3. A modified sine inverter has no output
  4. A pure sine wave inverter has a low-distortion sinusoidal output; a modified one has a stepped waveform
Show answer & solution

Answer: (D) A pure sine wave inverter has a low-distortion sinusoidal output; a modified one has a stepped waveform

Modified sine inverters can make motors and transformers hot and noisy.

Question 20

What is the function of the DC link capacitor in a voltage source inverter?

  1. To limit fault current
  2. To filter AC output
  3. To keep the DC voltage stiff and supply ripple currents
  4. To isolate the load
Show answer & solution

Answer: (C) To keep the DC voltage stiff and supply ripple currents

It is a key component of VFDs.

Question 21

What is a grid-forming inverter?

  1. An inverter that sets voltage and frequency itself, able to support or form a grid
  2. A diode bridge
  3. A DC chopper
  4. An inverter that only follows the grid
Show answer & solution

Answer: (A) An inverter that sets voltage and frequency itself, able to support or form a grid

Grid-forming inverters are important for high renewable penetration.

Question 22

What is the switching frequency typical of IGBT inverters in industrial drives?

  1. About 1 Hz
  2. About 1 MHz
  3. About 2 to 20 kHz
  4. About 50 Hz
Show answer & solution

Answer: (C) About 2 to 20 kHz

Higher frequencies reduce current ripple but raise switching losses.

Question 23

What is the main advantage of a transformerless solar inverter?

  1. Higher efficiency and lower weight and cost
  2. Galvanic isolation
  3. Larger size
  4. Higher losses
Show answer & solution

Answer: (A) Higher efficiency and lower weight and cost

Leakage current must be controlled carefully.

Question 24

How is the output voltage of a PWM inverter varied with a fixed DC supply?

  1. By changing the load
  2. By changing the switch type
  3. By changing the DC capacitor
  4. By varying the modulation index
Show answer & solution

Answer: (D) By varying the modulation index

Changing the reference frequency varies output frequency.

Question 25

What happens to the output voltage of an inverter when the DC link voltage falls?

  1. The output voltage rises
  2. Nothing changes
  3. The output frequency doubles
  4. The maximum available output voltage falls
Show answer & solution

Answer: (D) The maximum available output voltage falls

Drives may limit speed or torque on low DC voltage.

Question 26

Why do inverters for motors use PWM rather than square-wave switching?

  1. PWM needs no switches
  2. PWM gives near-sinusoidal current, reducing heating, noise and torque ripple
  3. PWM produces more low-order harmonics
  4. Square-wave switching is always better
Show answer & solution

Answer: (B) PWM gives near-sinusoidal current, reducing heating, noise and torque ripple

PWM also allows variable voltage at variable frequency.

Question 27

What is overmodulation in sinusoidal PWM?

  1. Operation at zero frequency
  2. Operation without a carrier
  3. Operation with a modulation index above 1, increasing output but adding low-order harmonics
  4. Operation at zero output
Show answer & solution

Answer: (C) Operation with a modulation index above 1, increasing output but adding low-order harmonics

In the extreme it approaches square-wave operation.

Question 28

What is a bidirectional inverter in a hybrid solar system?

  1. An inverter that can convert DC to AC and also charge batteries from AC
  2. An inverter that only converts DC to AC
  3. A DC chopper
  4. A rectifier only
Show answer & solution

Answer: (A) An inverter that can convert DC to AC and also charge batteries from AC

Hybrid inverters manage solar, batteries and grid together.

Question 29

Which inverter output type is recommended for running sensitive electronics and motors from batteries?

  1. Modified square wave only
  2. Pure sine wave
  3. DC output
  4. Square wave
Show answer & solution

Answer: (B) Pure sine wave

Pure sine output avoids overheating and noise.

Question 30

What is the role of a phase-locked loop (PLL) in a grid-tie inverter?

  1. To increase DC voltage
  2. To measure temperature
  3. To track grid voltage phase and frequency so the inverter can synchronise
  4. To store energy
Show answer & solution

Answer: (C) To track grid voltage phase and frequency so the inverter can synchronise

Accurate synchronisation is needed before and during power export.

Question 31

What is the main function of the battery in an off-grid solar inverter system?

  1. To act as a fuse
  2. To raise the panel voltage
  3. To produce AC directly
  4. To store energy for use when solar power is not available
Show answer & solution

Answer: (D) To store energy for use when solar power is not available

The inverter converts battery DC to AC.

Question 32

Why is the efficiency of modern solar inverters important?

  1. It affects only colour
  2. It is not important
  3. It changes panel temperature only
  4. Losses directly reduce the energy delivered from the panels
Show answer & solution

Answer: (D) Losses directly reduce the energy delivered from the panels

Good inverters exceed 97% efficiency.

Practice these 32 questions interactively →