Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Systems: Stability and Control

Electrical Engineering · Power Systems

35 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is steady-state stability?

  1. The ability to restart after blackout
  2. The ability of a system to stay in synchronism after small, gradual changes in load
  3. The ability to withstand large faults
  4. The ability to reduce frequency
Show answer & solution

Answer: (B) The ability of a system to stay in synchronism after small, gradual changes in load

It is limited by the maximum power transfer.

Question 2

What is transient stability?

  1. The frequency at no load
  2. The response to small load changes
  3. The ability of a system to remain in synchronism after a large sudden disturbance such as a fault
  4. The steady-state voltage
Show answer & solution

Answer: (C) The ability of a system to remain in synchronism after a large sudden disturbance such as a fault

It depends on fault type, location and clearing time.

Question 3

What does the swing equation describe?

  1. The motion of a generator rotor angle in response to the difference between mechanical and electrical power
  2. The voltage of a bus
  3. The flow of reactive power
  4. The sag of lines
Show answer & solution

Answer: (A) The motion of a generator rotor angle in response to the difference between mechanical and electrical power

M d²δ/dt² = Pm − Pe.

Question 4

How is the inertia constant H of a generator defined?

  1. Speed divided by frequency
  2. Voltage divided by current
  3. Power divided by speed
  4. Stored kinetic energy at rated speed divided by the machine MVA rating
Show answer & solution

Answer: (D) Stored kinetic energy at rated speed divided by the machine MVA rating

H is in MJ/MVA or seconds.

Question 5

Which criterion is used to assess transient stability of a single machine connected to an infinite bus?

  1. Equal area criterion
  2. Nyquist criterion
  3. N−1 criterion
  4. Kelvin's law
Show answer & solution

Answer: (A) Equal area criterion

The accelerating and decelerating areas must balance.

Question 6

What is the critical clearing time?

  1. The time to start a generator
  2. The time to repair a fault
  3. The maximum time a fault can last before the system loses stability
  4. The time between relays
Show answer & solution

Answer: (C) The maximum time a fault can last before the system loses stability

Faster clearing improves transient stability.

Question 7

Which measure improves transient stability of a power system?

  1. Removing damper windings
  2. Faster fault clearing with high-speed breakers and relays
  3. Lower transmission voltage
  4. Slower breakers
Show answer & solution

Answer: (B) Faster fault clearing with high-speed breakers and relays

Auto-reclosing and series compensation also help.

Question 8

What is the maximum power that can be transferred over a lossless line between voltages V1 and V2 with reactance X?

  1. V1V2X
  2. (V1 + V2)/X
  3. X/(V1V2)
  4. V1V2/X
Show answer & solution

Answer: (D) V1V2/X

Maximum transfer occurs at a power angle of 90°.

Question 9

What is the purpose of a power system stabiliser (PSS)?

  1. To start generators
  2. To add damping to rotor oscillations through the excitation system
  3. To raise frequency
  4. To limit fault current
Show answer & solution

Answer: (B) To add damping to rotor oscillations through the excitation system

PSSs improve small-signal stability.

Question 10

What is the main function of governor droop control?

  1. To control reactive power
  2. To start motors
  3. To share load changes among generators in proportion to their ratings and limit frequency deviation
  4. To keep voltage constant
Show answer & solution

Answer: (C) To share load changes among generators in proportion to their ratings and limit frequency deviation

A typical droop is about 4–5%.

Question 11

What is automatic generation control (AGC)?

  1. A system that adjusts generator outputs to restore frequency and scheduled interchange
  2. A protection relay
  3. A load forecasting tool
  4. A voltage regulator only
Show answer & solution

Answer: (A) A system that adjusts generator outputs to restore frequency and scheduled interchange

AGC is secondary frequency control.

Question 12

What does system frequency fall indicate in a power system?

  1. Voltage is too high
  2. Reactive power is too high
  3. Generation exceeds load
  4. Generation is less than load
Show answer & solution

Answer: (D) Generation is less than load

Frequency is the indicator of real power balance.

Question 13

What is under-frequency load shedding?

  1. Automatic disconnection of selected loads when frequency falls below set limits
  2. Shedding generation at high frequency
  3. Reducing voltage at night
  4. Switching capacitors
Show answer & solution

Answer: (A) Automatic disconnection of selected loads when frequency falls below set limits

It prevents total system collapse.

Question 14

Which devices are used to control voltage in power systems?

  1. Energy meters
  2. Circuit breakers only
  3. Governors only
  4. AVRs, transformer tap changers, shunt capacitors, reactors, SVCs and STATCOMs
Show answer & solution

Answer: (D) AVRs, transformer tap changers, shunt capacitors, reactors, SVCs and STATCOMs

Voltage control relies on reactive power control.

Question 15

What is a STATCOM?

  1. A type of transformer
  2. A circuit breaker
  3. A voltage-source converter that supplies or absorbs reactive power rapidly
  4. A generator governor
Show answer & solution

Answer: (C) A voltage-source converter that supplies or absorbs reactive power rapidly

It is a FACTS device for voltage support.

Question 16

What does FACTS stand for in power systems?

  1. Frequency and Current Transmission Standards
  2. Flexible AC Transmission Systems
  3. Fast AC Transmission Switching
  4. Fixed Alternating Current Transformers
Show answer & solution

Answer: (B) Flexible AC Transmission Systems

FACTS devices control power flow and voltage.

Question 17

What is voltage collapse?

  1. A fault current
  2. A rise in voltage at light load
  3. A progressive uncontrollable fall in voltage due to insufficient reactive power support
  4. A frequency increase
Show answer & solution

Answer: (C) A progressive uncontrollable fall in voltage due to insufficient reactive power support

It often follows heavy loading and loss of generators or lines.

Question 18

What is islanding in a power system?

  1. A ground fault
  2. A part of the network separating from the grid and continuing to operate on its own generation
  3. An open circuit in a transformer
  4. Overvoltage due to lightning
Show answer & solution

Answer: (B) A part of the network separating from the grid and continuing to operate on its own generation

Controlled islanding can prevent total blackout.

Question 19

Which centre in Islamabad controls and dispatches Pakistan's national grid?

  1. National Power Control Centre (NPCC)
  2. NEPRA headquarters
  3. PEC office
  4. K-Electric control room
Show answer & solution

Answer: (A) National Power Control Centre (NPCC)

NPCC monitors and dispatches generation across the national grid.

Question 20

What is SCADA used for in power systems?

  1. Measuring insulation
  2. Billing consumers only
  3. Designing towers
  4. Remote monitoring and control of substations and networks
Show answer & solution

Answer: (D) Remote monitoring and control of substations and networks

Supervisory Control and Data Acquisition systems support grid operation.

Question 21

What is dynamic stability?

  1. Stability with no controls
  2. The ability of a system to remain stable over a longer period with controls such as AVRs and governors acting
  3. The stability of insulators
  4. The stability of transformers
Show answer & solution

Answer: (B) The ability of a system to remain stable over a longer period with controls such as AVRs and governors acting

It considers small oscillations with control actions.

Question 22

How does increasing transmission voltage affect steady-state stability limit?

  1. It increases the limit
  2. It makes the limit zero
  3. It decreases the limit
  4. It has no effect
Show answer & solution

Answer: (A) It increases the limit

Maximum power transfer is proportional to V1V2.

Question 23

What is the main purpose of auto-reclosing on transmission lines?

  1. To increase fault current
  2. To change frequency
  3. To delay fault clearing
  4. To restore the line quickly after transient faults
Show answer & solution

Answer: (D) To restore the line quickly after transient faults

Most faults on overhead lines are temporary.

Question 24

What happens to generator rotor angle during a fault close to the generator?

  1. It becomes zero instantly
  2. It stays constant
  3. It increases because electrical output falls while mechanical input stays nearly constant
  4. It decreases
Show answer & solution

Answer: (C) It increases because electrical output falls while mechanical input stays nearly constant

The rotor accelerates during the fault.

Question 25

What is an SVC (static VAR compensator)?

  1. A circuit breaker
  2. A transformer tap changer only
  3. A thyristor-controlled combination of reactors and capacitors that regulates reactive power
  4. A rotating synchronous condenser
Show answer & solution

Answer: (C) A thyristor-controlled combination of reactors and capacitors that regulates reactive power

SVCs provide fast voltage support.

Question 26

What is the purpose of a primary frequency response from generators?

  1. Billing
  2. Long-term economic dispatch
  3. Planning new plants
  4. Immediate automatic change of output by governors when frequency changes
Show answer & solution

Answer: (D) Immediate automatic change of output by governors when frequency changes

Primary response acts within seconds.

Question 27

What is the typical permissible frequency range for normal operation of a 50 Hz grid?

  1. Exactly 50 Hz with no deviation possible
  2. Close to 50 Hz within a small band of about ±1%
  3. Between 0 and 100 Hz
  4. Between 40 and 60 Hz
Show answer & solution

Answer: (B) Close to 50 Hz within a small band of about ±1%

Grid codes set normal and emergency frequency bands.

Question 28

What is load–frequency control?

  1. Control of generator outputs to keep frequency and tie-line power at scheduled values
  2. Control of insulation
  3. Control of fault currents
  4. Control of voltage only
Show answer & solution

Answer: (A) Control of generator outputs to keep frequency and tie-line power at scheduled values

It combines governor action and AGC.

Question 29

Why does a large sudden loss of generation cause frequency to fall?

  1. Voltage rises
  2. Line resistance increases
  3. Reactive power increases
  4. Load exceeds generation, so rotating machines slow down as kinetic energy is drawn
Show answer & solution

Answer: (D) Load exceeds generation, so rotating machines slow down as kinetic energy is drawn

System inertia slows the initial rate of fall.

Question 30

How does low system inertia, as with high solar and wind penetration, affect frequency stability?

  1. Frequency changes faster after disturbances
  2. Voltage becomes zero
  3. Frequency becomes perfectly constant
  4. It has no effect
Show answer & solution

Answer: (A) Frequency changes faster after disturbances

Fast frequency response and synthetic inertia help offset low inertia.

Question 31

What is a tie line in power systems?

  1. A line to a single house
  2. A transmission line interconnecting two control areas or systems
  3. A grounding conductor
  4. A cable in a building
Show answer & solution

Answer: (B) A transmission line interconnecting two control areas or systems

Power exchange over tie lines is scheduled and controlled.

Question 32

What is the main cause of hunting (rotor oscillations) between interconnected generators?

  1. Low frequency supply only
  2. Constant load
  3. Sudden changes in load or system conditions with insufficient damping
  4. High damping
Show answer & solution

Answer: (C) Sudden changes in load or system conditions with insufficient damping

Damper windings and PSSs reduce oscillations.

Question 33

How does series compensation improve stability of long lines?

  1. It lowers frequency
  2. It reduces line reactance, increasing maximum power transfer
  3. It increases reactance
  4. It reduces voltage
Show answer & solution

Answer: (B) It reduces line reactance, increasing maximum power transfer

Too much series compensation can cause subsynchronous resonance.

Question 34

What is subsynchronous resonance?

  1. A high frequency harmonic
  2. A lightning surge
  3. An oscillation between series-compensated line electrical modes and turbine-generator shaft torsional modes
  4. A DC offset
Show answer & solution

Answer: (C) An oscillation between series-compensated line electrical modes and turbine-generator shaft torsional modes

It can damage turbine-generator shafts.

Question 35

What is the main purpose of a grid code?

  1. To license engineers
  2. To set building codes
  3. To set electricity prices only
  4. To set technical rules for connecting to and operating on the transmission system
Show answer & solution

Answer: (D) To set technical rules for connecting to and operating on the transmission system

NEPRA approves the grid code in Pakistan.

Practice these 35 questions interactively →