Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Systems: Load Flow and Per Unit

Electrical Engineering · Power Systems

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the main purpose of load flow analysis in a power network?

  1. To select protective relay settings only
  2. To locate underground cable faults
  3. To measure generator insulation strength
  4. To calculate steady-state operating conditions such as voltages, angles and power flows
Show answer & solution

Answer: (D) To calculate steady-state operating conditions such as voltages, angles and power flows

Load flow studies are used for planning and operation.

Question 2

Which matrix relates bus current injections to bus voltages in a power network?

  1. Jacobian matrix
  2. Bus admittance matrix (Ybus)
  3. Incidence matrix
  4. Transformation matrix
Show answer & solution

Answer: (B) Bus admittance matrix (Ybus)

I = YbusV.

Question 3

Which quantities are specified at the slack (swing) bus in load flow studies?

  1. Voltage magnitude and angle
  2. Reactive power and angle
  3. Real power and voltage magnitude
  4. Real and reactive power
Show answer & solution

Answer: (A) Voltage magnitude and angle

The slack bus supplies the system losses.

Question 4

Which quantities are specified at a PV (generator) bus?

  1. Reactive power and angle
  2. Real and reactive power
  3. Voltage magnitude and angle
  4. Real power and voltage magnitude
Show answer & solution

Answer: (D) Real power and voltage magnitude

Reactive power and angle are calculated.

Question 5

Which quantities are specified at a PQ (load) bus?

  1. Real power and voltage magnitude
  2. Voltage magnitude and angle
  3. Real and reactive power
  4. Only voltage magnitude
Show answer & solution

Answer: (C) Real and reactive power

Most buses in a network are PQ buses.

Question 6

What is the main role of the slack bus in load flow analysis?

  1. To carry no power
  2. To balance generation and load by supplying system losses
  3. To set reactive power only
  4. To represent loads
Show answer & solution

Answer: (B) To balance generation and load by supplying system losses

Losses are not known until the solution is found.

Question 7

Why is the Ybus matrix of a large power system described as sparse?

  1. All elements are non-zero
  2. It has no diagonal
  3. It has only one row
  4. Most buses are connected to only a few other buses, so most elements are zero
Show answer & solution

Answer: (D) Most buses are connected to only a few other buses, so most elements are zero

Sparsity techniques make large studies efficient.

Question 8

How is the diagonal element Yii of the bus admittance matrix formed?

  1. By adding all admittances connected to bus i
  2. By adding all impedances
  3. By taking the negative of one line admittance
  4. By setting it to zero
Show answer & solution

Answer: (A) By adding all admittances connected to bus i

Off-diagonal elements are the negative of the admittance between buses.

Question 9

What is the main disadvantage of the Gauss–Seidel load flow method?

  1. It always diverges
  2. It needs a Jacobian
  3. Slow convergence for large systems
  4. It cannot handle PV buses
Show answer & solution

Answer: (C) Slow convergence for large systems

It is simple and needs little memory.

Question 10

What is the main advantage of the Newton–Raphson load flow method?

  1. It works only for radial systems
  2. Fast (quadratic) convergence in few iterations
  3. It needs no Jacobian
  4. It uses no matrices
Show answer & solution

Answer: (B) Fast (quadratic) convergence in few iterations

Each iteration needs the Jacobian matrix.

Question 11

What is the basis of the fast decoupled load flow method?

  1. Losses are zero
  2. All quantities are fully coupled
  3. Real power is mainly linked to voltage angles and reactive power to voltage magnitudes
  4. Voltages are constant
Show answer & solution

Answer: (C) Real power is mainly linked to voltage angles and reactive power to voltage magnitudes

Decoupling speeds up solution of large transmission networks.

Question 12

How is per-unit impedance defined?

  1. Actual impedance divided by base impedance
  2. Actual impedance in ohms
  3. Base impedance divided by actual impedance
  4. Actual impedance multiplied by base impedance
Show answer & solution

Answer: (A) Actual impedance divided by base impedance

Per-unit values simplify calculations across voltage levels.

Question 13

How is base impedance calculated from base voltage and base MVA?

  1. Zbase = kV base × MVA base
  2. Zbase = kV base/MVA base
  3. Zbase = MVA base/(kV base)²
  4. Zbase = (kV base)²/MVA base
Show answer & solution

Answer: (D) Zbase = (kV base)²/MVA base

It is in ohms.

Question 14

What is the base impedance for an 11 kV, 100 MVA base?

  1. 0.121 Ω
  2. 1.21 Ω
  3. 12.1 Ω
  4. 110 Ω
Show answer & solution

Answer: (B) 1.21 Ω

Zbase = 11²/100 = 1.21 Ω.

Question 15

How is a per-unit impedance converted from an old base to a new base?

  1. Znew = Zold × (MVAnew/MVAold) × (kVold/kVnew)²
  2. Znew = Zold × (kVnew/kVold)²
  3. Znew = Zold
  4. Znew = Zold × (MVAold/MVAnew)
Show answer & solution

Answer: (A) Znew = Zold × (MVAnew/MVAold) × (kVold/kVnew)²

Equipment impedances are given on their own ratings.

Question 16

What is a key advantage of the per-unit system?

  1. It makes all voltages zero
  2. It increases accuracy of meters
  3. A transformer's per-unit impedance is the same on both sides
  4. It removes the need for impedances
Show answer & solution

Answer: (C) A transformer's per-unit impedance is the same on both sides

Per-unit values of similar equipment fall in narrow ranges.

Question 17

What is the condition for economic dispatch of generators neglecting losses?

  1. The cheapest generator is fully loaded first only
  2. All generators have equal output
  3. All generators run at minimum load
  4. All generators operate at equal incremental fuel cost
Show answer & solution

Answer: (D) All generators operate at equal incremental fuel cost

Equal incremental cost minimises total generation cost.

Question 18

What is a penalty factor in economic dispatch?

  1. A fine for low power factor
  2. A factor that adjusts incremental cost of a plant for its effect on transmission losses
  3. A tax on fuel
  4. A reliability index
Show answer & solution

Answer: (B) A factor that adjusts incremental cost of a plant for its effect on transmission losses

Plants far from loads are penalised for higher losses.

Question 19

What is unit commitment?

  1. Deciding which generating units should be on or off over a period to meet demand at minimum cost
  2. Building new plants
  3. Setting relay times
  4. Dispatching a single unit only
Show answer & solution

Answer: (A) Deciding which generating units should be on or off over a period to meet demand at minimum cost

It considers start-up costs, minimum run times and reserves.

Question 20

In contingency analysis, what does the N−1 security criterion require?

  1. Failure of all generators
  2. The system must survive the outage of any one major element without violating limits
  3. Isolation of every bus
  4. Removal of two lines at once
Show answer & solution

Answer: (B) The system must survive the outage of any one major element without violating limits

N−1 is a basic planning and operating criterion.

Question 21

Which quantity is mainly controlled by the flow of reactive power in a transmission network?

  1. Frequency
  2. Fuel cost
  3. Bus voltage magnitude
  4. Real power flow
Show answer & solution

Answer: (C) Bus voltage magnitude

Reactive power shortage causes low voltages.

Question 22

Which quantity mainly determines real power flow between two buses?

  1. The bus number
  2. The difference in voltage magnitudes only
  3. The frequency of each bus
  4. The difference in voltage phase angles
Show answer & solution

Answer: (D) The difference in voltage phase angles

P ≈ (V1V2/X) sin δ.

Question 23

What is DC load flow?

  1. Load flow for DC systems only
  2. A protection study
  3. A method to locate faults
  4. A simplified linear load flow that assumes flat voltages and small angle differences
Show answer & solution

Answer: (D) A simplified linear load flow that assumes flat voltages and small angle differences

It is fast and used for contingency screening.

Question 24

What is the Zbus matrix mainly used for?

  1. Fault calculations, since its elements give driving-point and transfer impedances
  2. Load flow only
  3. Billing
  4. Insulation design
Show answer & solution

Answer: (A) Fault calculations, since its elements give driving-point and transfer impedances

Zbus is the inverse of Ybus.

Question 25

What is optimal power flow (OPF)?

  1. A stability study only
  2. A fault study
  3. A load flow that optimises an objective such as cost while meeting network limits
  4. A load flow with no limits
Show answer & solution

Answer: (C) A load flow that optimises an objective such as cost while meeting network limits

OPF adjusts generation and controls within constraints.

Question 26

Which method is commonly used for short-term load forecasting?

  1. Random guessing
  2. Statistical and artificial intelligence models using past load and weather data
  3. Fault analysis
  4. Relay coordination
Show answer & solution

Answer: (B) Statistical and artificial intelligence models using past load and weather data

Accurate forecasts help unit commitment and dispatch.

Question 27

What is the typical per-unit impedance range of large power transformers?

  1. About 0.001 pu
  2. About 0.05 to 0.15 pu
  3. About 1 to 2 pu
  4. About 10 pu
Show answer & solution

Answer: (B) About 0.05 to 0.15 pu

Typical impedances fall within narrow ranges in per unit.

Question 28

Which loss formula expresses transmission losses in terms of generator outputs?

  1. Steinmetz formula
  2. Peek's formula
  3. Kron's B-coefficient loss formula
  4. Kelvin's law
Show answer & solution

Answer: (C) Kron's B-coefficient loss formula

PL = ΣΣ Pi Bij Pj.

Question 29

What happens to a PV bus in load flow if its reactive power limit is exceeded?

  1. It is converted to a PQ bus with Q fixed at the limit
  2. It becomes the slack bus
  3. Its voltage becomes zero
  4. It is removed
Show answer & solution

Answer: (A) It is converted to a PQ bus with Q fixed at the limit

The voltage then can no longer be held at the set value.

Question 30

What is the per-unit value of a 500 kV voltage on a 500 kV base?

  1. 0.002 pu
  2. 0.5 pu
  3. 1.0 pu
  4. 500 pu
Show answer & solution

Answer: (C) 1.0 pu

Per unit = actual/base.

Question 31

What is the per-unit reactance of a 0.1 pu transformer on its own 50 MVA rating when converted to a 100 MVA base at the same voltage?

  1. 0.05 pu
  2. 0.1 pu
  3. 0.2 pu
  4. 0.4 pu
Show answer & solution

Answer: (C) 0.2 pu

Znew = 0.1 × (100/50) = 0.2 pu.

Question 32

What does the Jacobian matrix contain in Newton–Raphson load flow?

  1. Line impedances only
  2. Partial derivatives of power equations with respect to voltage angles and magnitudes
  3. Fault currents
  4. Generator costs
Show answer & solution

Answer: (B) Partial derivatives of power equations with respect to voltage angles and magnitudes

It is recalculated in each iteration.

Question 33

What is a flat start in load flow studies?

  1. Starting with all voltages at zero
  2. Starting with real loads removed
  3. Starting with fault conditions
  4. Starting iterations with all bus voltages at 1.0 pu and zero angle
Show answer & solution

Answer: (D) Starting iterations with all bus voltages at 1.0 pu and zero angle

It is the usual initial guess.

Question 34

What does a load flow study show when a line is overloaded?

  1. Power flow exceeding the line's thermal rating
  2. Zero current
  3. High insulation resistance
  4. Low frequency only
Show answer & solution

Answer: (A) Power flow exceeding the line's thermal rating

Planners then add lines or reroute power.

Practice these 34 questions interactively →