Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Systems: Power Generation

Electrical Engineering · Power Systems

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Why is a steam condenser installed at the exhaust of a thermal power plant turbine?

  1. To control alternator excitation
  2. To reduce generator frequency
  3. To increase boiler pressure
  4. To condense exhaust steam and maintain a low exhaust pressure, increasing turbine output and efficiency
Show answer & solution

Answer: (D) To condense exhaust steam and maintain a low exhaust pressure, increasing turbine output and efficiency

Low back pressure increases the enthalpy drop across the turbine.

Question 2

On which thermodynamic cycle does a steam power plant work?

  1. Diesel cycle
  2. Rankine cycle
  3. Otto cycle
  4. Brayton cycle
Show answer & solution

Answer: (B) Rankine cycle

Gas turbines work on the Brayton cycle.

Question 3

What is the function of an economiser in a steam power plant?

  1. To superheat steam
  2. To cool the condenser
  3. To preheat boiler feedwater using heat from flue gases
  4. To remove ash
Show answer & solution

Answer: (C) To preheat boiler feedwater using heat from flue gases

It improves overall boiler efficiency.

Question 4

What is the function of an air preheater in a thermal plant?

  1. To heat combustion air using flue gases
  2. To cool turbine bearings
  3. To heat feedwater
  4. To superheat steam
Show answer & solution

Answer: (A) To heat combustion air using flue gases

Hot combustion air improves fuel burning and efficiency.

Question 5

What is the function of a superheater in a boiler?

  1. To condense steam
  2. To remove moisture from air
  3. To raise steam temperature above saturation temperature
  4. To heat feedwater
Show answer & solution

Answer: (C) To raise steam temperature above saturation temperature

Superheated steam increases cycle efficiency and reduces turbine blade erosion.

Question 6

What is the typical overall efficiency of a conventional steam power station?

  1. About 5 to 10%
  2. About 30 to 40%
  3. About 80 to 90%
  4. About 95%
Show answer & solution

Answer: (B) About 30 to 40%

Most of the heat is rejected in the condenser.

Question 7

What is the approximate efficiency of a modern combined cycle gas turbine plant?

  1. About 20%
  2. About 35%
  3. About 55 to 60%
  4. About 90%
Show answer & solution

Answer: (C) About 55 to 60%

Exhaust heat from the gas turbine raises steam for a steam turbine.

Question 8

Which formula gives the electrical power output of a hydroelectric plant?

  1. P = gH/Q
  2. P = ρQ/H
  3. P = QH/η
  4. P = ρgQHη
Show answer & solution

Answer: (D) P = ρgQHη

ρ is water density, Q flow rate, H net head and η overall efficiency.

Question 9

What is the approximate power output of a hydro plant with a flow of 100 m³/s, a net head of 100 m and an efficiency of 90%?

  1. About 8.8 MW
  2. About 88 MW
  3. About 98 MW
  4. About 880 MW
Show answer & solution

Answer: (B) About 88 MW

P = 1000 × 9.81 × 100 × 100 × 0.9 ≈ 88.3 MW.

Question 10

Which hydraulic turbine is most suitable for very high heads?

  1. Pelton wheel
  2. Bulb turbine
  3. Propeller turbine
  4. Kaplan turbine
Show answer & solution

Answer: (A) Pelton wheel

Pelton is an impulse turbine for heads of several hundred metres.

Question 11

Which hydraulic turbine is most suitable for low heads and large flows?

  1. Pelton wheel
  2. Cross-flow only for high heads
  3. Turgo turbine
  4. Kaplan turbine
Show answer & solution

Answer: (D) Kaplan turbine

Kaplan turbines have adjustable runner blades.

Question 12

What is the purpose of a surge tank in a hydroelectric plant?

  1. To reduce water hammer pressure in the penstock when load changes suddenly
  2. To store fuel
  3. To raise the head
  4. To cool the generator
Show answer & solution

Answer: (A) To reduce water hammer pressure in the penstock when load changes suddenly

It absorbs pressure surges and supplies water during load increases.

Question 13

Which is the largest hydroelectric power station in Pakistan?

  1. Tarbela
  2. Ghazi Barotha
  3. Mangla
  4. Warsak
Show answer & solution

Answer: (A) Tarbela

Tarbela on the Indus River is one of the world's largest earth-filled dams.

Question 14

On which river is the Mangla hydropower station located?

  1. Chenab
  2. Indus
  3. Jhelum
  4. Kabul
Show answer & solution

Answer: (C) Jhelum

Mangla Dam was completed in 1967.

Question 15

What is the role of control rods in a nuclear reactor?

  1. To generate steam
  2. To absorb neutrons and control the rate of the chain reaction
  3. To cool the core
  4. To moderate neutrons
Show answer & solution

Answer: (B) To absorb neutrons and control the rate of the chain reaction

Control rods are made of boron, cadmium or hafnium.

Question 16

What is the function of a moderator in a nuclear reactor?

  1. To absorb all neutrons
  2. To cool the turbine
  3. To produce electricity
  4. To slow down fast neutrons so they can cause further fission
Show answer & solution

Answer: (D) To slow down fast neutrons so they can cause further fission

Water, heavy water and graphite are common moderators.

Question 17

Which nuclear power plants operate near Karachi using Hualong One reactors?

  1. Chashma C-1 and C-2
  2. Mangla units
  3. Tarbela units
  4. K-2 and K-3
Show answer & solution

Answer: (D) K-2 and K-3

Each unit has a capacity of about 1,100 MW.

Question 18

Which region of Sindh is Pakistan's main wind power corridor?

  1. Thar–Islamkot
  2. Hub–Lasbela
  3. Gharo–Jhimpir
  4. Sukkur–Rohri
Show answer & solution

Answer: (C) Gharo–Jhimpir

Many wind farms operate in this coastal corridor.

Question 19

How is load factor defined?

  1. Average load divided by maximum demand over a period
  2. Maximum demand divided by connected load
  3. Sum of maximum demands divided by system maximum demand
  4. Energy generated divided by installed capacity only
Show answer & solution

Answer: (A) Average load divided by maximum demand over a period

A high load factor means better use of plant.

Question 20

What is the load factor of a plant with an average load of 60 MW and a maximum demand of 100 MW?

  1. 40%
  2. 60%
  3. 100%
  4. 167%
Show answer & solution

Answer: (B) 60%

LF = 60/100 = 0.6.

Question 21

How is demand factor defined?

  1. Connected load divided by maximum demand
  2. Average load divided by maximum demand
  3. Energy divided by time
  4. Maximum demand divided by connected load
Show answer & solution

Answer: (D) Maximum demand divided by connected load

Demand factor is normally less than one.

Question 22

How is diversity factor defined?

  1. Sum of individual maximum demands divided by the maximum demand of the whole system
  2. Maximum demand divided by connected load
  3. Average load divided by maximum demand
  4. Installed capacity divided by peak load
Show answer & solution

Answer: (A) Sum of individual maximum demands divided by the maximum demand of the whole system

Diversity factor is greater than one and reduces required capacity.

Question 23

What is plant capacity factor?

  1. Number of units divided by capacity
  2. Maximum demand divided by rated capacity only
  3. Actual energy produced divided by the energy that would be produced at full rated capacity over the same period
  4. Fuel cost divided by energy
Show answer & solution

Answer: (C) Actual energy produced divided by the energy that would be produced at full rated capacity over the same period

Capacity factor shows how fully a plant is used.

Question 24

Which plants are best suited for base load operation?

  1. Pumped storage plants
  2. Nuclear and large coal plants
  3. Gas turbine peaking plants
  4. Diesel standby sets
Show answer & solution

Answer: (B) Nuclear and large coal plants

Base load plants run continuously at high load factor.

Question 25

Which plants are best suited for meeting peak loads?

  1. Gas turbines, hydro and pumped storage plants
  2. Large coal plants only
  3. Run-of-river plants only
  4. Nuclear plants
Show answer & solution

Answer: (A) Gas turbines, hydro and pumped storage plants

Peaking plants can start and change output quickly.

Question 26

What is a pumped storage plant?

  1. A plant that stores coal
  2. A hydro plant that pumps water to an upper reservoir during low demand and generates during peak demand
  3. A nuclear plant
  4. A solar thermal plant
Show answer & solution

Answer: (B) A hydro plant that pumps water to an upper reservoir during low demand and generates during peak demand

It acts like a large energy storage system.

Question 27

What is spinning reserve?

  1. The load during the night
  2. Capacity of stopped plants
  3. Generating capacity that is running and synchronised but not fully loaded, ready to pick up load quickly
  4. The capacity of transformers
Show answer & solution

Answer: (C) Generating capacity that is running and synchronised but not fully loaded, ready to pick up load quickly

It covers sudden loss of generation.

Question 28

What is a load curve?

  1. A graph of voltage against current
  2. A graph of efficiency against load
  3. A graph of fuel cost
  4. A graph of load demand against time
Show answer & solution

Answer: (D) A graph of load demand against time

The area under the daily load curve gives energy consumed.

Question 29

What is the purpose of a cooling tower in a thermal power plant?

  1. To cool the boiler
  2. To cool the generator stator directly
  3. To cool the condenser cooling water by evaporation before it is reused
  4. To store steam
Show answer & solution

Answer: (C) To cool the condenser cooling water by evaporation before it is reused

Natural draught and induced draught cooling towers are common.

Question 30

Which large solar power park is located near Bahawalpur, Punjab?

  1. Chashma Solar Park
  2. Quaid-e-Azam Solar Park
  3. Gharo Solar Park
  4. Thar Solar Park
Show answer & solution

Answer: (B) Quaid-e-Azam Solar Park

It was Pakistan's first large utility-scale solar project.

Question 31

What is the purpose of an electrostatic precipitator in a coal-fired plant?

  1. To heat feedwater
  2. To reduce sulphur in coal
  3. To cool the turbine
  4. To remove fly ash from flue gases
Show answer & solution

Answer: (D) To remove fly ash from flue gases

It charges particles and collects them on plates.

Question 32

Which equipment removes sulphur dioxide from coal plant flue gases?

  1. Flue gas desulphurisation (FGD) system
  2. Electrostatic precipitator
  3. Economiser
  4. Superheater
Show answer & solution

Answer: (A) Flue gas desulphurisation (FGD) system

Limestone scrubbing is the most common FGD method.

Question 33

Which Thar coalfield block supplies lignite to mine-mouth power plants operated with Engro?

  1. Block-II
  2. Block-XII
  3. Block-VIII
  4. Block-XX
Show answer & solution

Answer: (A) Block-II

Thar Block-II feeds several 330 MW units.

Question 34

What is the main advantage of a run-of-river hydro plant?

  1. It can follow peak load at any time
  2. It needs little or no reservoir storage
  3. It can store water for months
  4. It uses coal
Show answer & solution

Answer: (B) It needs little or no reservoir storage

Ghazi Barotha is an example of a run-of-river scheme on the Indus.

Question 35

Which type of turbine is commonly used for medium heads in large hydro plants?

  1. Kaplan only
  2. Wind turbine
  3. Francis turbine
  4. Pelton wheel
Show answer & solution

Answer: (C) Francis turbine

Francis turbines are reaction turbines with fixed blades.

Question 36

What does "black start" capability mean for a power station?

  1. Starting with coal only
  2. Starting at night only
  3. Starting only at full load
  4. The ability to start without external power from the grid
Show answer & solution

Answer: (D) The ability to start without external power from the grid

Hydro and gas units are often used to restart the grid after a blackout.

Question 37

What is the main advantage of a combined heat and power (cogeneration) plant?

  1. Waste heat is used for industrial or heating needs, raising overall efficiency
  2. It produces no heat
  3. It cannot supply electricity
  4. It needs no fuel
Show answer & solution

Answer: (A) Waste heat is used for industrial or heating needs, raising overall efficiency

Overall efficiency can exceed 75%.

Question 38

Which Pakistani nuclear power plants are located on the Indus River in Punjab?

  1. Tarbela units
  2. Chashma units C-1 to C-4
  3. KANUPP-1 only
  4. K-2 and K-3
Show answer & solution

Answer: (B) Chashma units C-1 to C-4

Chashma uses pressurised water reactors.

Practice these 38 questions interactively →