Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Systems: Fault Analysis

Electrical Engineering · Power Systems

33 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which type of fault is the most common in power systems?

  1. Three-phase symmetrical fault
  2. Double line-to-ground fault
  3. Line-to-line fault
  4. Single line-to-ground fault
Show answer & solution

Answer: (D) Single line-to-ground fault

About 70–80% of faults on overhead lines are single line-to-ground.

Question 2

Which type of fault is usually the most severe but least frequent?

  1. Single line-to-ground fault
  2. Line-to-line fault
  3. Open-conductor fault
  4. Three-phase symmetrical fault
Show answer & solution

Answer: (D) Three-phase symmetrical fault

It produces the highest fault currents in most systems.

Question 3

Which symmetrical component represents a balanced set having the normal phase sequence?

  1. Zero-sequence component
  2. Positive-sequence component
  3. Negative-sequence component
  4. Neutral-sequence component
Show answer & solution

Answer: (B) Positive-sequence component

Normal balanced operation contains only positive sequence quantities.

Question 4

How are the sequence networks connected for a single line-to-ground fault?

  1. Positive, negative and zero sequence networks in series
  2. All three in parallel
  3. Positive and negative in parallel only
  4. Zero sequence alone
Show answer & solution

Answer: (A) Positive, negative and zero sequence networks in series

The fault current is If = 3E/(Z1 + Z2 + Z0 + 3Zf).

Question 5

How are the sequence networks connected for a line-to-line fault?

  1. All three in series
  2. Positive sequence alone
  3. Zero sequence alone
  4. Positive and negative sequence networks in parallel
Show answer & solution

Answer: (D) Positive and negative sequence networks in parallel

No zero sequence current flows in a line-to-line fault.

Question 6

How are the sequence networks connected for a double line-to-ground fault?

  1. Only negative sequence
  2. All three in series
  3. Positive network in series with the parallel combination of negative and zero networks
  4. Positive and zero in series only
Show answer & solution

Answer: (C) Positive network in series with the parallel combination of negative and zero networks

Zero sequence current flows through the earth.

Question 7

What is the fault level of a bus with a Thevenin reactance of 0.1 pu on a 100 MVA base?

  1. 10 MVA
  2. 100 MVA
  3. 1,000 MVA
  4. 10,000 MVA
Show answer & solution

Answer: (C) 1,000 MVA

Fault MVA = base MVA/Xpu = 100/0.1.

Question 8

What is the purpose of current-limiting reactors in power systems?

  1. To limit fault current to values that equipment can withstand
  2. To increase fault current
  3. To store energy
  4. To improve power factor
Show answer & solution

Answer: (A) To limit fault current to values that equipment can withstand

They are placed in feeders, bus sections or generator circuits.

Question 9

What is solid earthing of a power system neutral?

  1. Connecting through a capacitor
  2. Connecting the neutral directly to earth without intentional impedance
  3. Leaving the neutral isolated
  4. Connecting through a large resistor
Show answer & solution

Answer: (B) Connecting the neutral directly to earth without intentional impedance

Solid earthing is common at high voltages.

Question 10

What is a Petersen coil?

  1. An adjustable reactor in the neutral that cancels capacitive earth fault current
  2. A transformer winding
  3. A current transformer
  4. A capacitor bank
Show answer & solution

Answer: (A) An adjustable reactor in the neutral that cancels capacitive earth fault current

It is also called an arc suppression coil.

Question 11

What is arcing ground in an ungrounded system?

  1. A blown fuse
  2. Repeated arcing at an earth fault caused by capacitive currents, producing overvoltages
  3. A lightning strike
  4. Normal load current
Show answer & solution

Answer: (B) Repeated arcing at an earth fault caused by capacitive currents, producing overvoltages

Neutral earthing prevents arcing grounds.

Question 12

What is the ratio of the making current of a circuit breaker to its rated symmetrical breaking current (RMS)?

  1. 1.0
  2. 1.414
  3. 2.55
  4. 5.0
Show answer & solution

Answer: (C) 2.55

Making current includes the maximum DC offset (doubling effect).

Question 13

Why does the first peak of short-circuit current exceed the symmetrical peak?

  1. The generator voltage rises
  2. The frequency doubles
  3. The resistance becomes zero
  4. A DC offset is present depending on the instant of fault
Show answer & solution

Answer: (D) A DC offset is present depending on the instant of fault

The asymmetric peak may approach twice the symmetrical peak.

Question 14

Which generator reactance is used to calculate the initial symmetrical fault current?

  1. Synchronous reactance
  2. Leakage reactance of the transformer only
  3. Transient reactance only after many seconds
  4. Subtransient reactance
Show answer & solution

Answer: (D) Subtransient reactance

X″d gives the highest initial current.

Question 15

How does a delta winding affect the flow of zero-sequence current?

  1. It doubles it
  2. It blocks zero-sequence current from passing between the line sides, although it can circulate inside the delta
  3. It allows zero-sequence current freely
  4. It converts it to positive sequence
Show answer & solution

Answer: (B) It blocks zero-sequence current from passing between the line sides, although it can circulate inside the delta

Transformer connections determine zero sequence networks.

Question 16

What is a series (open-conductor) fault?

  1. A fault in which one or two conductors are broken, causing unbalanced flow
  2. A short to earth
  3. A lightning strike
  4. A short between phases
Show answer & solution

Answer: (A) A fault in which one or two conductors are broken, causing unbalanced flow

Broken conductors and blown fuses cause series faults.

Question 17

What is the short-circuit capacity of a bus?

  1. The rated load of the bus
  2. The bus voltage only
  3. The product of prefault voltage and fault current, expressed in MVA
  4. The number of feeders
Show answer & solution

Answer: (C) The product of prefault voltage and fault current, expressed in MVA

It indicates the strength of the system at that point.

Question 18

What is the fault current in per unit for a three-phase fault with prefault voltage 1.0 pu and Thevenin reactance 0.25 pu?

  1. 0.25 pu
  2. 1.25 pu
  3. 2.5 pu
  4. 4 pu
Show answer & solution

Answer: (D) 4 pu

If = 1.0/0.25 = 4 pu.

Question 19

Which theorem is commonly used to calculate fault currents in power networks?

  1. Millman's theorem
  2. Thevenin's theorem
  3. Tellegen's theorem
  4. Reciprocity theorem
Show answer & solution

Answer: (B) Thevenin's theorem

The network is replaced by its Thevenin equivalent at the fault point.

Question 20

Why is resistance earthing used in some medium-voltage systems?

  1. To limit earth fault current and reduce damage while still allowing protection to operate
  2. To isolate the neutral
  3. To improve power factor
  4. To increase fault current
Show answer & solution

Answer: (A) To limit earth fault current and reduce damage while still allowing protection to operate

It is common in industrial and generator neutrals.

Question 21

What is the zero-sequence impedance of a line usually compared with its positive-sequence impedance?

  1. Lower
  2. Higher
  3. Equal
  4. Zero
Show answer & solution

Answer: (B) Higher

It includes the earth return path.

Question 22

What happens to fault current levels as a power system grows with more generation and interconnection?

  1. They increase
  2. They become zero
  3. They remain constant
  4. They decrease
Show answer & solution

Answer: (A) They increase

Breakers and busbars may need upgrading.

Question 23

What is the relation between positive and negative sequence impedances of static equipment such as lines and transformers?

  1. Negative is twice positive
  2. Positive is always zero
  3. Negative is always zero
  4. They are equal
Show answer & solution

Answer: (D) They are equal

For rotating machines they differ.

Question 24

How many times larger is the line-to-ground fault current than the zero-sequence current?

  1. √3 times
  2. Equal
  3. 3 times
  4. One third
Show answer & solution

Answer: (C) 3 times

Ia = 3I0 for a single line-to-ground fault.

Question 25

Which condition holds at the fault point for a bolted single line-to-ground fault on phase a?

  1. All phase currents are equal
  2. All phase voltages are zero
  3. The current of phase a is zero
  4. The voltage of phase a is zero
Show answer & solution

Answer: (D) The voltage of phase a is zero

Currents in the healthy phases are zero.

Question 26

Why are fault studies needed in power system design?

  1. To calculate wages
  2. To select breaker ratings, design protection and check equipment withstand
  3. To forecast weather
  4. To design tariffs
Show answer & solution

Answer: (B) To select breaker ratings, design protection and check equipment withstand

Fault currents determine mechanical and thermal stresses.

Question 27

What causes the decaying AC component of fault current in a generator?

  1. Load increase
  2. Capacitor switching
  3. Changing generator reactance from subtransient to transient to synchronous values
  4. Changes in supply frequency
Show answer & solution

Answer: (C) Changing generator reactance from subtransient to transient to synchronous values

Damper and field windings produce subtransient and transient periods.

Question 28

What is the main effect of a fault on system voltage near the fault point?

  1. A sharp voltage drop (sag)
  2. Frequency doubling
  3. No change
  4. A large voltage rise only
Show answer & solution

Answer: (A) A sharp voltage drop (sag)

Voltage dips affect sensitive loads across the network.

Question 29

What is a bolted fault?

  1. A fault with zero fault impedance
  2. A fault through high resistance
  3. An open circuit
  4. A fault caused by bolts only
Show answer & solution

Answer: (A) A fault with zero fault impedance

Bolted faults give maximum fault current.

Question 30

What is the purpose of earthing transformers (zig-zag transformers) in delta systems?

  1. To measure current
  2. To provide a neutral point for earthing and a path for zero-sequence current
  3. To step up voltage
  4. To supply loads
Show answer & solution

Answer: (B) To provide a neutral point for earthing and a path for zero-sequence current

They allow earth fault protection in delta systems.

Question 31

What is the effect of fault resistance on earth fault current?

  1. It makes the current infinite
  2. It increases the fault current
  3. It has no effect
  4. It reduces the fault current
Show answer & solution

Answer: (D) It reduces the fault current

High-resistance faults can be hard to detect.

Question 32

Why are generator neutrals often earthed through high resistance?

  1. To increase fault current
  2. To reduce voltage
  3. To limit stator earth fault current and damage to the core
  4. To improve efficiency
Show answer & solution

Answer: (C) To limit stator earth fault current and damage to the core

Generator earth faults can burn core laminations.

Question 33

Which fault produces negative-sequence currents that can overheat generator rotors?

  1. Unbalanced faults such as line-to-line faults
  2. DC faults only
  3. No-load operation
  4. Balanced three-phase load
Show answer & solution

Answer: (A) Unbalanced faults such as line-to-line faults

Negative-sequence currents induce double-frequency currents in the rotor.

Practice these 33 questions interactively →