Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Power Systems: Distribution Systems

Electrical Engineering · Power Systems

35 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which conductor carries power from a substation to distribution areas without intermediate tappings?

  1. Service mains
  2. Feeder
  3. Distributor
  4. Neutral wire
Show answer & solution

Answer: (B) Feeder

Current in a feeder is the same along its length.

Question 2

What is a distributor in a distribution system?

  1. A conductor without tappings
  2. The service cable to a house only
  3. A transmission tower
  4. A conductor from which tappings are taken to supply consumers
Show answer & solution

Answer: (D) A conductor from which tappings are taken to supply consumers

Current varies along a distributor.

Question 3

What are service mains?

  1. Main feeders from grid stations
  2. Small cables connecting a distributor to a consumer's premises
  3. Earth wires
  4. Transmission lines
Show answer & solution

Answer: (B) Small cables connecting a distributor to a consumer's premises

They are usually overhead drops or underground cables.

Question 4

What is the main advantage of a ring main distribution system over a radial system?

  1. Better reliability because consumers can be supplied from either end
  2. Simpler protection
  3. Lower cost
  4. Fewer switches
Show answer & solution

Answer: (A) Better reliability because consumers can be supplied from either end

A fault can be isolated without interrupting all consumers.

Question 5

What is the main disadvantage of a radial distribution system?

  1. It is very complex
  2. A fault interrupts all consumers beyond it
  3. It is very costly
  4. It needs many sources
Show answer & solution

Answer: (B) A fault interrupts all consumers beyond it

Radial systems are simple and cheap but less reliable.

Question 6

At what voltage is primary distribution commonly carried out by DISCOs in Pakistan?

  1. 11 kV
  2. 220 kV
  3. 400 V
  4. 500 kV
Show answer & solution

Answer: (A) 11 kV

11 kV feeders supply pole-mounted distribution transformers.

Question 7

At what voltages is low-voltage distribution supplied to consumers in Pakistan?

  1. 11 kV and 33 kV
  2. 132 kV
  3. 400 V three-phase and 230 V single-phase
  4. 500 kV
Show answer & solution

Answer: (C) 400 V three-phase and 230 V single-phase

Distribution transformers step 11 kV down to these levels.

Question 8

Which company distributes electricity in most of Balochistan?

  1. PESCO
  2. HESCO
  3. LESCO
  4. QESCO
Show answer & solution

Answer: (D) QESCO

Quetta Electric Supply Company serves most of the province.

Question 9

Which company supplies electricity in Lahore and surrounding districts?

  1. MEPCO
  2. IESCO
  3. LESCO
  4. FESCO
Show answer & solution

Answer: (C) LESCO

Lahore Electric Supply Company is one of the largest DISCOs.

Question 10

Which electricity company in Pakistan is vertically integrated, handling generation, transmission and distribution in its area?

  1. LESCO
  2. K-Electric
  3. NTDC
  4. QESCO
Show answer & solution

Answer: (B) K-Electric

K-Electric serves Karachi and nearby areas.

Question 11

Which body regulates the electric power sector in Pakistan, including tariffs and licences?

  1. NEPRA
  2. WAPDA
  3. PEC
  4. OGRA
Show answer & solution

Answer: (A) NEPRA

The National Electric Power Regulatory Authority was set up under the NEPRA Act of 1997.

Question 12

Which agency buys power from generators on behalf of DISCOs in Pakistan?

  1. PEC
  2. OGRA
  3. NEPRA
  4. Central Power Purchasing Agency (CPPA-G)
Show answer & solution

Answer: (D) Central Power Purchasing Agency (CPPA-G)

CPPA-G manages the market settlement for the national grid.

Question 13

What is the voltage drop in a uniformly loaded distributor fed at one end compared with the same total load concentrated at the far end?

  1. Double
  2. Half
  3. One quarter
  4. The same
Show answer & solution

Answer: (B) Half

A uniformly distributed load behaves like the total load at the midpoint.

Question 14

What are technical losses in a distribution system?

  1. Losses due to resistance of lines and transformers
  2. Losses due to unpaid bills
  3. Losses due to electricity theft
  4. Losses due to meter errors only
Show answer & solution

Answer: (A) Losses due to resistance of lines and transformers

Non-technical losses include theft and billing errors.

Question 15

What are non-technical losses in electricity distribution?

  1. Copper losses in lines
  2. Iron losses in transformers
  3. Corona losses
  4. Losses due to theft, unmetered supply and billing errors
Show answer & solution

Answer: (D) Losses due to theft, unmetered supply and billing errors

Reducing them is a major challenge for DISCOs.

Question 16

Which measure reduces technical losses in an 11 kV distribution network?

  1. Adding more loads to long feeders
  2. Using thinner conductors
  3. Reducing feeder length and installing capacitors to improve power factor
  4. Running feeders unbalanced
Show answer & solution

Answer: (C) Reducing feeder length and installing capacitors to improve power factor

Shorter feeders and higher conductor size also help.

Question 17

What is net metering under NEPRA regulations?

  1. A meter for industrial loads only
  2. A method of tariff increase
  3. A meter that measures only imports
  4. A system where consumers with solar panels export surplus energy to the grid and are billed for net consumption
Show answer & solution

Answer: (D) A system where consumers with solar panels export surplus energy to the grid and are billed for net consumption

It encourages distributed solar generation.

Question 18

What is the purpose of an advanced metering infrastructure (smart meters)?

  1. To measure and communicate consumption data remotely in real time
  2. To generate power
  3. To increase theft
  4. To reduce voltage
Show answer & solution

Answer: (A) To measure and communicate consumption data remotely in real time

Smart meters help reduce losses and improve billing accuracy.

Question 19

Where is a distribution transformer usually installed in Pakistani residential areas?

  1. At 500 kV grid stations
  2. Inside power plants only
  3. On poles or platforms close to the load centre
  4. At the consumer's meter
Show answer & solution

Answer: (C) On poles or platforms close to the load centre

Locating transformers near load reduces LV losses.

Question 20

What is the function of a grid station in the distribution system?

  1. To generate power
  2. To step down transmission voltage and feed sub-transmission or distribution feeders
  3. To bill consumers
  4. To store energy
Show answer & solution

Answer: (B) To step down transmission voltage and feed sub-transmission or distribution feeders

132/11 kV grid stations are common in DISCO networks.

Question 21

Why should loads be balanced among the three phases of an LV distribution system?

  1. To reduce neutral current, losses and voltage unbalance
  2. To increase neutral current
  3. To reduce transformer rating
  4. To increase losses
Show answer & solution

Answer: (A) To reduce neutral current, losses and voltage unbalance

Unbalance overloads one phase and the neutral.

Question 22

What is the purpose of a recloser on an overhead distribution feeder?

  1. To reduce voltage permanently
  2. To measure energy
  3. To automatically reclose after temporary faults and restore supply
  4. To earth the feeder
Show answer & solution

Answer: (C) To automatically reclose after temporary faults and restore supply

Most overhead faults are temporary, such as bird or branch contact.

Question 23

What is an interconnected (mesh) distribution system?

  1. A system without transformers
  2. A DC system
  3. A single radial feeder
  4. A network fed from several sources so that supply continues if one source fails
Show answer & solution

Answer: (D) A network fed from several sources so that supply continues if one source fails

Mesh networks are used in dense urban areas.

Question 24

What is the main advantage of underground distribution cables in cities?

  1. Lower cost than overhead lines
  2. Better safety, appearance and reliability against weather
  3. Easier fault location
  4. Lower capacitance
Show answer & solution

Answer: (B) Better safety, appearance and reliability against weather

Underground systems cost more but suit dense areas.

Question 25

What is voltage regulation in a distribution feeder concerned with?

  1. Reducing current to zero
  2. Keeping consumer voltage within permitted limits as load varies
  3. Increasing power factor above one
  4. Measuring frequency
Show answer & solution

Answer: (B) Keeping consumer voltage within permitted limits as load varies

Tap changers and capacitors help control voltage.

Question 26

What do ACSR code names such as Dog, Rabbit and Osprey indicate?

  1. Transformer ratings
  2. Tower types
  3. Standard conductor sizes and strandings
  4. Insulator types
Show answer & solution

Answer: (C) Standard conductor sizes and strandings

Each name represents a specific aluminium and steel combination.

Question 27

Which supply system is used by Pakistani DISCOs for 11 kV distribution feeders?

  1. Three-phase three-wire
  2. Two-phase four-wire
  3. Single-phase two-wire
  4. DC two-wire
Show answer & solution

Answer: (A) Three-phase three-wire

The 400 V system is three-phase four-wire with a neutral.

Question 28

What does PEC stand for in Pakistan's engineering profession?

  1. Public Engineering Committee
  2. Power Energy Commission
  3. Pakistan Electric Company
  4. Pakistan Engineering Council
Show answer & solution

Answer: (D) Pakistan Engineering Council

PEC registers engineers and regulates the engineering profession.

Question 29

What is the main function of a sub-transmission network?

  1. To carry power at intermediate voltages such as 132 kV or 66 kV from grid stations to distribution substations
  2. To carry power at 400 V
  3. To generate power
  4. To supply single homes
Show answer & solution

Answer: (A) To carry power at intermediate voltages such as 132 kV or 66 kV from grid stations to distribution substations

It links transmission and distribution.

Question 30

What is the function of a ring main unit (RMU) in underground distribution?

  1. A transformer winding
  2. A capacitor bank
  3. A compact switchgear unit that allows switching and protection of cable ring circuits
  4. A meter
Show answer & solution

Answer: (C) A compact switchgear unit that allows switching and protection of cable ring circuits

RMUs are common in urban 11 kV cable networks.

Question 31

Why are distribution feeders sectionalised with switches or sectionalisers?

  1. To increase losses
  2. To store energy
  3. To increase voltage
  4. To isolate faulty sections and restore supply to healthy parts
Show answer & solution

Answer: (D) To isolate faulty sections and restore supply to healthy parts

Sectionalising improves reliability indices.

Question 32

What does SAIDI measure in distribution reliability?

  1. The average duration of interruptions per customer per year
  2. The total energy sold
  3. The average number of interruptions per customer
  4. The peak demand
Show answer & solution

Answer: (A) The average duration of interruptions per customer per year

SAIFI measures average frequency of interruptions.

Question 33

What is a dedicated feeder?

  1. A feeder shared by many homes
  2. A feeder with no load
  3. An 11 kV feeder that supplies a single large consumer
  4. A street light circuit
Show answer & solution

Answer: (C) An 11 kV feeder that supplies a single large consumer

Industries often take dedicated feeders for reliability.

Question 34

What is the main purpose of a distribution capacitor bank on an 11 kV feeder?

  1. To store real energy
  2. To supply reactive power locally, improving voltage and reducing losses
  3. To reduce frequency
  4. To protect against lightning
Show answer & solution

Answer: (B) To supply reactive power locally, improving voltage and reducing losses

Capacitors reduce current in upstream lines.

Question 35

What is load shedding in the Pakistani context?

  1. Building new feeders
  2. Planned interruption of supply to consumers when demand exceeds available supply or for loss control
  3. Increasing supply at night
  4. Testing meters
Show answer & solution

Answer: (B) Planned interruption of supply to consumers when demand exceeds available supply or for loss control

Planned outages are scheduled by DISCOs.

Practice these 35 questions interactively →