Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Electrical Machines: Transformers

Electrical Engineering · Electrical Machines

41 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

On which principle does a transformer work?

  1. Thermionic emission
  2. Electrostatic induction
  3. Self-induction in a single straight conductor
  4. Mutual induction between two windings linked by a common magnetic flux
Show answer & solution

Answer: (D) Mutual induction between two windings linked by a common magnetic flux

A changing flux from the primary induces an emf in the secondary.

Question 2

What is the emf equation of a transformer winding?

  1. E = 2π N Φm
  2. E = 4.44 f N Φm
  3. E = f N Φm/4.44
  4. E = 4.44 f N/Φm
Show answer & solution

Answer: (B) E = 4.44 f N Φm

Φm is the peak flux in the core.

Question 3

What emf is induced in a 500-turn winding at 50 Hz with a peak core flux of 0.01 Wb?

  1. 111 V
  2. 222 V
  3. 1,110 V
  4. 11,100 V
Show answer & solution

Answer: (C) 1,110 V

E = 4.44 × 50 × 500 × 0.01 = 1,110 V.

Question 4

Why is a transformer core made of thin laminations?

  1. To reduce eddy current loss
  2. To reduce hysteresis loss only
  3. To increase copper loss
  4. To increase leakage flux
Show answer & solution

Answer: (A) To reduce eddy current loss

Insulated laminations break up eddy current paths.

Question 5

Why is silicon steel used for transformer cores?

  1. It has very high hysteresis loss
  2. It is a good conductor
  3. It is cheaper than all other metals
  4. It has low hysteresis loss and higher resistivity
Show answer & solution

Answer: (D) It has low hysteresis loss and higher resistivity

About 3% silicon reduces core losses.

Question 6

How does hysteresis loss vary according to Steinmetz's formula?

  1. In proportion to the square of current
  2. It is independent of frequency
  3. In proportion to frequency and to Bm raised to about 1.6
  4. In proportion to the square of frequency
Show answer & solution

Answer: (C) In proportion to frequency and to Bm raised to about 1.6

Wh = η f Bm^1.6 V.

Question 7

How does eddy current loss in a core vary with frequency?

  1. Inversely with frequency
  2. With the square of frequency
  3. Directly with frequency
  4. It is independent of frequency
Show answer & solution

Answer: (B) With the square of frequency

We ∝ f² Bm² t², where t is lamination thickness.

Question 8

How do the copper losses of a transformer vary with load?

  1. With the square of the load current
  2. Inversely with load
  3. They remain constant
  4. Directly with load current
Show answer & solution

Answer: (A) With the square of the load current

Copper loss = I²R.

Question 9

Why are the iron losses of a transformer called constant losses?

  1. They are always zero
  2. They depend on voltage and frequency, which stay nearly constant, not on load
  3. They depend on power factor
  4. They depend on load current
Show answer & solution

Answer: (B) They depend on voltage and frequency, which stay nearly constant, not on load

Iron loss is present whenever the transformer is energised.

Question 10

When does a transformer operate at maximum efficiency?

  1. When copper loss is zero
  2. At no load
  3. When copper loss equals iron loss
  4. When iron loss is zero
Show answer & solution

Answer: (C) When copper loss equals iron loss

This occurs at a fraction √(Pi/Pcu,fl) of full load.

Question 11

What does the open-circuit test on a transformer mainly determine?

  1. Iron (core) losses and the magnetising branch parameters
  2. Winding polarity
  3. Full-load copper loss
  4. Equivalent impedance
Show answer & solution

Answer: (A) Iron (core) losses and the magnetising branch parameters

It is done on the LV side with the HV side open.

Question 12

What does the short-circuit test on a transformer mainly determine?

  1. No-load current
  2. Iron loss
  3. Turns ratio only
  4. Full-load copper loss and equivalent impedance
Show answer & solution

Answer: (D) Full-load copper loss and equivalent impedance

It is done on the HV side with the LV side shorted at reduced voltage.

Question 13

Why is the short-circuit test normally performed on the HV side?

  1. Rated current on the HV side is lower and the required voltage is a convenient value
  2. It gives iron loss directly
  3. The LV side cannot be shorted
  4. The HV side has no resistance
Show answer & solution

Answer: (A) Rated current on the HV side is lower and the required voltage is a convenient value

Only a few percent of rated voltage is needed to circulate rated current.

Question 14

What is the voltage regulation of a transformer?

  1. The ratio of output to input power
  2. The change in secondary voltage from no load to full load, as a percentage of full-load voltage
  3. The iron loss as a percentage
  4. The turns ratio
Show answer & solution

Answer: (B) The change in secondary voltage from no load to full load, as a percentage of full-load voltage

Low regulation is desirable.

Question 15

For which transformers is all-day efficiency an important measure?

  1. Power transformers at generating stations
  2. Welding transformers
  3. Instrument transformers
  4. Distribution transformers, which are energised all day but loaded variably
Show answer & solution

Answer: (D) Distribution transformers, which are energised all day but loaded variably

All-day efficiency is based on energy over 24 hours.

Question 16

What is the turns ratio of an 11,000/400 V distribution transformer?

  1. 0.036
  2. 2.75
  3. 27.5
  4. 275
Show answer & solution

Answer: (C) 27.5

11,000/400 = 27.5.

Question 17

How does a transformer affect the supply frequency?

  1. It doubles the frequency
  2. It halves the frequency
  3. It converts AC to DC
  4. It does not change the frequency
Show answer & solution

Answer: (D) It does not change the frequency

Transformers change voltage and current levels only.

Question 18

What happens if a transformer primary is connected to a DC supply of rated voltage?

  1. A very large current flows because there is no back emf, and the winding may burn
  2. It works normally
  3. Output becomes AC
  4. The core loss becomes zero
Show answer & solution

Answer: (A) A very large current flows because there is no back emf, and the winding may burn

With steady DC, only the winding resistance limits current.

Question 19

What is the main difference between core-type and shell-type transformers?

  1. Shell type has no windings
  2. In core type windings surround the core; in shell type the core surrounds the windings
  3. Core type has no core
  4. There is no difference
Show answer & solution

Answer: (B) In core type windings surround the core; in shell type the core surrounds the windings

Shell type gives better mechanical support against short-circuit forces.

Question 20

What is the purpose of the conservator tank in an oil-filled transformer?

  1. To cool the oil by fans
  2. To store spare windings
  3. To allow for expansion and contraction of oil and keep the main tank full
  4. To measure voltage
Show answer & solution

Answer: (C) To allow for expansion and contraction of oil and keep the main tank full

It also reduces the oil surface exposed to air.

Question 21

What is the purpose of the breather with silica gel on a transformer?

  1. To release gas from faults
  2. To cool the oil
  3. To measure oil level
  4. To remove moisture from air entering the conservator
Show answer & solution

Answer: (D) To remove moisture from air entering the conservator

Silica gel turns pink when saturated with moisture.

Question 22

What are the two main functions of transformer oil?

  1. Cooling and magnetisation
  2. Lubrication and lighting
  3. Insulation and cooling
  4. Magnetisation and insulation
Show answer & solution

Answer: (C) Insulation and cooling

Mineral oil carries heat away and insulates windings.

Question 23

What does the cooling designation ONAN mean?

  1. Oil natural, air natural
  2. Oil nitrogen, air nitrogen
  3. Oil neutral, air neutral
  4. Oil normal, air normal
Show answer & solution

Answer: (A) Oil natural, air natural

ONAF adds forced air cooling by fans.

Question 24

What is the purpose of an on-load tap changer?

  1. To reduce iron loss
  2. To adjust the voltage ratio without interrupting the load
  3. To change frequency
  4. To protect against lightning
Show answer & solution

Answer: (B) To adjust the voltage ratio without interrupting the load

Tap changers keep secondary voltage within limits as load varies.

Question 25

Why are tap changers usually fitted on the HV winding?

  1. HV side has no insulation
  2. The HV side has fewer turns
  3. The current is lower and fine voltage steps are easier on the HV side
  4. LV windings cannot be tapped
Show answer & solution

Answer: (C) The current is lower and fine voltage steps are easier on the HV side

Lower current reduces contact wear and arcing.

Question 26

What is the main advantage of an autotransformer over a two-winding transformer of the same rating?

  1. It uses less copper and has higher efficiency
  2. It provides electrical isolation
  3. It is safer for large ratios
  4. It has higher leakage reactance
Show answer & solution

Answer: (A) It uses less copper and has higher efficiency

A single winding is shared by primary and secondary.

Question 27

What is the main disadvantage of an autotransformer?

  1. It uses more copper
  2. There is no electrical isolation between primary and secondary
  3. It has lower efficiency
  4. It cannot step down voltage
Show answer & solution

Answer: (B) There is no electrical isolation between primary and secondary

A fault can apply the full primary voltage to the secondary side.

Question 28

Which condition is essential for parallel operation of two transformers?

  1. Same weight
  2. Same colour and size
  3. Same manufacturer
  4. Same voltage ratio, polarity, phase sequence and vector group
Show answer & solution

Answer: (D) Same voltage ratio, polarity, phase sequence and vector group

Equal per-unit impedance also ensures proper load sharing.

Question 29

What does the vector group Dyn11 of a distribution transformer indicate?

  1. Star HV, delta LV, in phase
  2. Delta HV, delta LV, 330° lag
  3. Delta HV, star LV with neutral, and LV leading HV by 30°
  4. Star HV, star LV, no neutral
Show answer & solution

Answer: (C) Delta HV, star LV with neutral, and LV leading HV by 30°

Dyn11 is widely used for 11 kV/400 V distribution transformers.

Question 30

What is magnetising inrush current?

  1. A large transient current drawn when a transformer is first energised
  2. The steady no-load current
  3. The short-circuit current
  4. The load current
Show answer & solution

Answer: (A) A large transient current drawn when a transformer is first energised

Inrush can be many times rated current and contains second harmonics.

Question 31

What is the typical no-load current of a power transformer as a percentage of rated current?

  1. About 0.01%
  2. About 2 to 5%
  3. About 50%
  4. About 100%
Show answer & solution

Answer: (B) About 2 to 5%

It is mainly magnetising current lagging the voltage by nearly 90°.

Question 32

What causes the leakage reactance of a transformer?

  1. The winding resistance
  2. The core loss
  3. The oil
  4. Flux that links only one winding and not the other
Show answer & solution

Answer: (D) Flux that links only one winding and not the other

Leakage reactance limits short-circuit current.

Question 33

What is the efficiency of a transformer delivering 100 kW with total losses of 2 kW?

  1. 96%
  2. About 98%
  3. 100%
  4. 102%
Show answer & solution

Answer: (B) About 98%

η = 100/(100 + 2) ≈ 98%.

Question 34

Why are transformers rated in kVA rather than kW?

  1. kVA is easier to measure
  2. They supply only reactive power
  3. Their output is always unity power factor
  4. Their losses depend on voltage and current, not on the load power factor
Show answer & solution

Answer: (D) Their losses depend on voltage and current, not on the load power factor

Copper loss depends on current and iron loss on voltage.

Question 35

Which test loads two identical transformers back-to-back for a heat run with little energy?

  1. Polarity test
  2. Megger test
  3. Sumpner's (back-to-back) test
  4. Open-circuit test only
Show answer & solution

Answer: (C) Sumpner's (back-to-back) test

Only losses are supplied from the mains.

Question 36

How does the efficiency of a transformer compare with that of rotating machines?

  1. It is higher because there are no moving parts and no friction losses
  2. It is the same
  3. It is always lower
  4. It is zero
Show answer & solution

Answer: (A) It is higher because there are no moving parts and no friction losses

Large transformers reach efficiencies above 99%.

Question 37

Why is the neutral of the star-connected LV winding of a distribution transformer earthed?

  1. To provide a reference for phase voltages and a path for earth fault current
  2. To reduce copper
  3. To change frequency
  4. To increase losses
Show answer & solution

Answer: (A) To provide a reference for phase voltages and a path for earth fault current

Earthing allows protective devices to operate on earth faults.

Question 38

What is the purpose of an impedance (per-unit) value on a transformer nameplate?

  1. To indicate frequency
  2. To indicate oil quality
  3. To indicate short-circuit current level, voltage regulation and parallel load sharing
  4. To indicate weight
Show answer & solution

Answer: (C) To indicate short-circuit current level, voltage regulation and parallel load sharing

Higher impedance lowers fault current but increases voltage drop.

Question 39

What is the effect of operating a 50 Hz transformer on a lower frequency at rated voltage?

  1. Efficiency improves greatly
  2. Losses fall to zero
  3. Output frequency increases
  4. Core flux increases and the core may saturate and overheat
Show answer & solution

Answer: (D) Core flux increases and the core may saturate and overheat

Flux is proportional to V/f.

Question 40

What is an instrument transformer?

  1. A transformer used to step down high voltages or currents for measurement and protection
  2. A welding transformer
  3. An autotransformer for motors
  4. A large power transformer
Show answer & solution

Answer: (A) A transformer used to step down high voltages or currents for measurement and protection

Current and voltage transformers feed meters and relays.

Question 41

What happens to the copper loss of a transformer at half load compared with full load?

  1. It doubles
  2. It stays the same
  3. It falls to one quarter
  4. It halves
Show answer & solution

Answer: (C) It falls to one quarter

Copper loss is proportional to the square of load current.

Practice these 41 questions interactively →