Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Electrical Machines: DC Machines

Electrical Engineering · Electrical Machines

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the primary function of the commutator in a DC generator?

  1. To reduce magnetic flux
  2. To improve mechanical balance
  3. To increase field resistance
  4. To deliver unidirectional current to the external circuit
Show answer & solution

Answer: (D) To deliver unidirectional current to the external circuit

It mechanically rectifies the alternating emf induced in the armature.

Question 2

What material are DC machine brushes usually made of?

  1. Copper sheet
  2. Carbon or graphite
  3. Steel
  4. Aluminium
Show answer & solution

Answer: (B) Carbon or graphite

Carbon gives good contact with low commutator wear.

Question 3

What is the emf equation of a DC generator?

  1. E = PΦZN/(60A)
  2. E = 4.44 f N Φ
  3. E = ΦZ/(PN)
  4. E = PZN/(60ΦA)
Show answer & solution

Answer: (A) E = PΦZN/(60A)

P poles, Z conductors, N rpm and A parallel paths.

Question 4

How many parallel paths does a lap winding have?

  1. Half the number of poles
  2. Equal to the number of poles
  3. Always one
  4. Always two
Show answer & solution

Answer: (B) Equal to the number of poles

Lap windings suit high-current, low-voltage machines.

Question 5

How many parallel paths does a wave winding have?

  1. One
  2. Four always
  3. Equal to the number of poles
  4. Two
Show answer & solution

Answer: (D) Two

Wave windings suit high-voltage, low-current machines.

Question 6

What is the generated emf of a 4-pole lap-wound generator with 0.02 Wb per pole, 400 conductors and 1,000 rpm?

  1. About 33 V
  2. About 133 V
  3. About 267 V
  4. About 533 V
Show answer & solution

Answer: (B) About 133 V

E = (4 × 0.02 × 400 × 1000)/(60 × 4) ≈ 133 V.

Question 7

What is armature reaction in a DC machine?

  1. Mechanical reaction of the armature
  2. Sparking at brushes only
  3. The effect of the armature magnetic field on the main field flux
  4. Heating of the field winding
Show answer & solution

Answer: (C) The effect of the armature magnetic field on the main field flux

It distorts and weakens the main field and shifts the neutral axis.

Question 8

What is the function of interpoles in a DC machine?

  1. To improve commutation by neutralising reactance voltage
  2. To act as brushes
  3. To reduce copper loss
  4. To increase speed
Show answer & solution

Answer: (A) To improve commutation by neutralising reactance voltage

Interpoles are connected in series with the armature.

Question 9

What is the function of compensating windings in large DC machines?

  1. To increase field flux greatly
  2. To reduce iron loss
  3. To start the motor
  4. To neutralise armature reaction under the pole faces
Show answer & solution

Answer: (D) To neutralise armature reaction under the pole faces

They are placed in slots in the pole faces.

Question 10

Why must a DC series motor never be started without a load?

  1. It reverses direction
  2. It cannot develop torque
  3. Its speed can rise to dangerously high values
  4. It draws no current
Show answer & solution

Answer: (C) Its speed can rise to dangerously high values

With little load, flux is small and speed rises very high.

Question 11

For which applications are DC series motors most suitable?

  1. Constant-speed lathes
  2. Traction and cranes needing high starting torque
  3. Recording instruments
  4. Clocks
Show answer & solution

Answer: (B) Traction and cranes needing high starting torque

Torque varies approximately with the square of current.

Question 12

Which DC motor runs at nearly constant speed from no load to full load?

  1. Shunt motor
  2. Universal motor
  3. Differential compound motor only
  4. Series motor
Show answer & solution

Answer: (A) Shunt motor

Its field flux is almost constant.

Question 13

How is the speed of a DC motor related to back emf and flux?

  1. N is independent of flux
  2. N is proportional to IaRa
  3. N is proportional to (V − IaRa)/Φ
  4. N is proportional to Φ/(V − IaRa)
Show answer & solution

Answer: (C) N is proportional to (V − IaRa)/Φ

Reducing flux increases speed.

Question 14

What is the back emf of a DC motor with V = 220 V, Ia = 20 A and Ra = 0.5 Ω?

  1. 200 V
  2. 210 V
  3. 220 V
  4. 230 V
Show answer & solution

Answer: (B) 210 V

Eb = V − IaRa = 220 − 10 = 210 V.

Question 15

How is the torque of a DC motor related to flux and armature current?

  1. T is independent of Ia
  2. T ∝ Ia/Φ
  3. T ∝ Φ/Ia
  4. T ∝ ΦIa
Show answer & solution

Answer: (D) T ∝ ΦIa

In a series motor Φ ∝ Ia, so T ∝ Ia² before saturation.

Question 16

Why is a starter needed for a DC motor?

  1. To reduce field current
  2. To increase speed
  3. At start there is no back emf, so the armature current would be very high
  4. To reverse rotation
Show answer & solution

Answer: (C) At start there is no back emf, so the armature current would be very high

The starter adds resistance that is cut out as speed rises.

Question 17

What protective feature does a three-point starter provide?

  1. Lightning protection
  2. Reverse power protection
  3. Earth fault protection
  4. No-volt release that returns the handle to OFF if supply fails
Show answer & solution

Answer: (D) No-volt release that returns the handle to OFF if supply fails

An overload release is also included.

Question 18

Which method gives smooth, wide-range speed control of a DC motor using a motor–generator set?

  1. Ward–Leonard system
  2. Plugging
  3. Field diverter only
  4. Star–delta starter
Show answer & solution

Answer: (A) Ward–Leonard system

Armature voltage is varied by controlling the generator field.

Question 19

Which test predetermines the efficiency of a DC shunt machine from no-load losses?

  1. Swinburne's test
  2. Short-circuit test
  3. Polarity test
  4. Hopkinson's test
Show answer & solution

Answer: (A) Swinburne's test

It is simple but ignores stray load losses under load.

Question 20

Which test uses two identical DC machines mechanically coupled, one as motor and one as generator?

  1. Blocked rotor test
  2. Open-circuit test
  3. Swinburne's test
  4. Hopkinson's (back-to-back) test
Show answer & solution

Answer: (D) Hopkinson's (back-to-back) test

Only losses are supplied from the mains.

Question 21

What is the critical field resistance of a DC shunt generator?

  1. The load resistance
  2. The minimum armature resistance
  3. The maximum field resistance with which the generator will build up voltage
  4. The resistance of the brushes
Show answer & solution

Answer: (C) The maximum field resistance with which the generator will build up voltage

Above it the generator fails to excite.

Question 22

What is needed in the poles for a self-excited DC generator to build up voltage?

  1. A permanent magnet only
  2. Residual magnetism
  3. Zero field resistance
  4. Reverse field connection
Show answer & solution

Answer: (B) Residual magnetism

Residual flux induces the initial emf.

Question 23

What does the open-circuit characteristic (magnetisation curve) of a DC generator show?

  1. Torque against speed
  2. Efficiency against load
  3. Generated emf against field current at constant speed
  4. Current against time
Show answer & solution

Answer: (C) Generated emf against field current at constant speed

It shows saturation of the magnetic circuit.

Question 24

What is a cumulative compound DC motor?

  1. A motor with no field
  2. A shunt motor only
  3. A motor whose series field opposes the shunt field
  4. A motor whose series field aids the shunt field
Show answer & solution

Answer: (D) A motor whose series field aids the shunt field

It combines good starting torque with limited no-load speed.

Question 25

When is the efficiency of a DC machine maximum?

  1. When variable (copper) losses equal constant losses
  2. When copper loss is zero
  3. When speed is maximum
  4. At no load
Show answer & solution

Answer: (A) When variable (copper) losses equal constant losses

This applies to most electrical machines.

Question 26

Why is the armature core of a DC machine laminated?

  1. To increase weight
  2. To reduce eddy current loss
  3. To improve commutation
  4. To increase hysteresis loss
Show answer & solution

Answer: (B) To reduce eddy current loss

Laminations are of silicon steel.

Question 27

Which rule gives the direction of induced emf in a generator?

  1. Fleming's left-hand rule
  2. Fleming's right-hand rule
  3. Lenz's law only
  4. Ampère's rule
Show answer & solution

Answer: (B) Fleming's right-hand rule

Fleming's left-hand rule gives the direction of force in a motor.

Question 28

What is dynamic (rheostatic) braking of a DC motor?

  1. Reversing supply polarity
  2. Increasing the field current only
  3. Applying mechanical brakes
  4. Disconnecting the armature from supply and connecting it across a resistor so it acts as a generator
Show answer & solution

Answer: (D) Disconnecting the armature from supply and connecting it across a resistor so it acts as a generator

Kinetic energy is dissipated in the resistor.

Question 29

What is plugging of a DC motor?

  1. Removing the field
  2. Increasing load
  3. Reversing the armature supply to stop the motor quickly
  4. Adding a capacitor
Show answer & solution

Answer: (C) Reversing the armature supply to stop the motor quickly

Plugging produces high current and needs a limiting resistor.

Question 30

What is regenerative braking?

  1. Braking in which the motor acts as a generator and returns energy to the supply
  2. Braking with a resistor
  3. Braking by reversing supply
  4. Braking with friction
Show answer & solution

Answer: (A) Braking in which the motor acts as a generator and returns energy to the supply

It is used in electric traction on down gradients.

Question 31

What causes sparking at the brushes of a DC machine?

  1. Too much field flux
  2. Low armature resistance
  3. Correct brush position
  4. Poor commutation due to reactance voltage in coils undergoing commutation
Show answer & solution

Answer: (D) Poor commutation due to reactance voltage in coils undergoing commutation

Interpoles and good brush grade reduce sparking.

Question 32

What is the function of equaliser rings in lap-wound DC machines?

  1. To start the motor
  2. To reduce iron loss
  3. To equalise voltages between parallel paths and reduce circulating currents through brushes
  4. To increase speed
Show answer & solution

Answer: (C) To equalise voltages between parallel paths and reduce circulating currents through brushes

Unequal air gaps can cause unequal path voltages.

Question 33

Why are dummy coils sometimes used in wave windings?

  1. To reduce copper
  2. To give mechanical balance when the number of coils does not suit the winding rule
  3. To increase voltage
  4. To act as interpoles
Show answer & solution

Answer: (B) To give mechanical balance when the number of coils does not suit the winding rule

They are not connected electrically.

Question 34

How can the direction of rotation of a DC shunt motor be reversed?

  1. By reversing either the armature or the field connections, but not both
  2. By reversing both armature and field
  3. By changing the supply frequency
  4. By reducing load
Show answer & solution

Answer: (A) By reversing either the armature or the field connections, but not both

Reversing both leaves the direction unchanged.

Question 35

What is the speed regulation of a DC motor?

  1. The maximum speed
  2. The change in field current
  3. The ratio of speed to torque
  4. The change in speed from no load to full load as a percentage of full-load speed
Show answer & solution

Answer: (D) The change in speed from no load to full load as a percentage of full-load speed

Shunt motors have low speed regulation.

Question 36

What material is commonly used for the yoke of small DC machines?

  1. Aluminium foil
  2. Cast iron or cast steel
  3. Copper
  4. Mica
Show answer & solution

Answer: (B) Cast iron or cast steel

The yoke carries flux and provides mechanical support.

Question 37

What is the main purpose of the pole shoes in a DC machine?

  1. To insulate the commutator
  2. To act as brushes
  3. To carry armature current
  4. To spread the flux over the armature and support the field coils
Show answer & solution

Answer: (D) To spread the flux over the armature and support the field coils

Pole shoes reduce air-gap reluctance.

Question 38

Why does the terminal voltage of a DC shunt generator fall as load increases?

  1. Armature resistance drop, armature reaction and reduced field current
  2. Field current increases
  3. Flux increases
  4. Speed increases
Show answer & solution

Answer: (A) Armature resistance drop, armature reaction and reduced field current

Compound generators compensate for this drop.

Question 39

What happens if the field winding of a running DC shunt motor is accidentally opened?

  1. The motor reverses
  2. The speed rises dangerously as flux falls to residual value
  3. The speed falls slightly
  4. The motor stops at once without danger
Show answer & solution

Answer: (B) The speed rises dangerously as flux falls to residual value

Field failure protection disconnects the supply.

Practice these 39 questions interactively →