Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Electrical Machines: Machine Materials

Electrical Engineering · Electrical Machines

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which material is generally selected for an electrical machine's structural frame?

  1. Cast iron or fabricated steel
  2. Porcelain
  3. Winding copper
  4. Mica sheet
Show answer & solution

Answer: (A) Cast iron or fabricated steel

The frame supports the core and protects internal parts.

Question 2

Which insulating material is commonly used between machine core laminations?

  1. Soft iron sheet
  2. Carbon steel layer
  3. Thin insulating varnish or oxide coating
  4. Thick copper coating
Show answer & solution

Answer: (C) Thin insulating varnish or oxide coating

It increases eddy current path resistance.

Question 3

What is the main purpose of insulation between winding conductors?

  1. To increase magnetic leakage
  2. To reduce mechanical speed
  3. To improve shaft alignment
  4. To prevent electrical short circuits
Show answer & solution

Answer: (D) To prevent electrical short circuits

Turn-to-turn and slot insulation withstand voltage stresses.

Question 4

What is the maximum operating temperature of Class F insulation?

  1. 105 °C
  2. 130 °C
  3. 155 °C
  4. 180 °C
Show answer & solution

Answer: (C) 155 °C

IEC insulation classes: A 105, E 120, B 130, F 155, H 180 °C.

Question 5

What is the maximum operating temperature of Class B insulation?

  1. 105 °C
  2. 130 °C
  3. 155 °C
  4. 180 °C
Show answer & solution

Answer: (B) 130 °C

Class B materials include mica, glass fibre and suitable resins.

Question 6

How does insulation life change with operating temperature according to the common rule of thumb?

  1. It halves for about every 10 °C rise above its rated temperature
  2. It halves for every 1 °C rise
  3. It is independent of temperature
  4. It doubles for every 10 °C rise
Show answer & solution

Answer: (A) It halves for about every 10 °C rise above its rated temperature

Overheating is a major cause of machine failure.

Question 7

What percentage of silicon is typically added to electrical steel?

  1. About 0.01%
  2. About 3 to 4%
  3. About 15%
  4. About 30%
Show answer & solution

Answer: (B) About 3 to 4%

Silicon increases resistivity and reduces losses.

Question 8

What is cold-rolled grain-oriented (CRGO) steel mainly used for?

  1. Machine shafts
  2. Commutator segments
  3. Brushes
  4. Transformer cores
Show answer & solution

Answer: (D) Transformer cores

Its grains are aligned for low loss along the rolling direction.

Question 9

What is the main advantage of amorphous metal transformer cores?

  1. Very low no-load (core) losses
  2. Higher hysteresis
  3. Very high copper losses
  4. Lower cost than all steels
Show answer & solution

Answer: (A) Very low no-load (core) losses

They are used in energy-efficient distribution transformers.

Question 10

What is the main advantage of copper over aluminium for windings?

  1. Lower melting point
  2. Lower cost
  3. Higher conductivity, allowing smaller windings
  4. Lower weight
Show answer & solution

Answer: (C) Higher conductivity, allowing smaller windings

Aluminium is lighter and cheaper but needs larger cross-section.

Question 11

Which material insulates commutator segments from one another?

  1. Copper
  2. Carbon
  3. Steel
  4. Mica
Show answer & solution

Answer: (D) Mica

Mica withstands heat and has good dielectric strength.

Question 12

From which material are commutator segments usually made?

  1. Cast iron
  2. Aluminium foil
  3. Hard-drawn copper
  4. Carbon
Show answer & solution

Answer: (C) Hard-drawn copper

Hard-drawn copper resists wear.

Question 13

What does the polarization index test of machine insulation compare?

  1. Voltage and current at full load
  2. Speed and torque
  3. Copper and iron losses
  4. Insulation resistance after 10 minutes with that after 1 minute
Show answer & solution

Answer: (D) Insulation resistance after 10 minutes with that after 1 minute

A PI of 2 or more usually indicates dry, clean insulation.

Question 14

What does "IP" stand for in an enclosure rating such as IP55?

  1. Insulation Power
  2. Ingress Protection
  3. Induction Performance
  4. Internal Pressure
Show answer & solution

Answer: (B) Ingress Protection

The digits show protection against solids and water.

Question 15

What does TEFC mean for a motor enclosure?

  1. Totally enclosed fan cooled
  2. Twin enclosed flow cooled
  3. Thermally efficient fully cooled
  4. Totally exposed forced cooling
Show answer & solution

Answer: (A) Totally enclosed fan cooled

An external fan blows air over a closed frame.

Question 16

What does duty type S1 on a motor nameplate mean?

  1. Intermittent periodic duty
  2. Continuous running duty at constant load
  3. Starting duty only
  4. Short-time duty
Show answer & solution

Answer: (B) Continuous running duty at constant load

Duty types are defined in IEC 60034-1.

Question 17

What is the typical thickness of transformer core laminations?

  1. About 0.001 mm
  2. About 0.25 to 0.35 mm
  3. About 1 cm
  4. About 5 mm
Show answer & solution

Answer: (B) About 0.25 to 0.35 mm

Thinner laminations reduce eddy losses.

Question 18

Which permanent magnet material gives the highest energy product in modern motors?

  1. Neodymium-iron-boron (NdFeB)
  2. Soft iron
  3. Ferrite
  4. Alnico
Show answer & solution

Answer: (A) Neodymium-iron-boron (NdFeB)

NdFeB magnets allow compact, high-efficiency motors.

Question 19

What property distinguishes soft magnetic materials used in machine cores?

  1. High retentivity for permanent magnets
  2. Zero permeability
  3. A narrow hysteresis loop with low coercivity
  4. A wide hysteresis loop
Show answer & solution

Answer: (C) A narrow hysteresis loop with low coercivity

Low hysteresis loss suits alternating flux.

Question 20

Why are ferrite cores used in high-frequency transformers?

  1. They have zero permeability
  2. They are very good conductors
  3. They are cheaper than air
  4. Their high resistivity keeps eddy current losses low at high frequency
Show answer & solution

Answer: (D) Their high resistivity keeps eddy current losses low at high frequency

Ferrites are used in switch-mode power supplies.

Question 21

What does the breakdown voltage (BDV) test of transformer oil measure?

  1. The flash point
  2. The colour of the oil
  3. The dielectric strength of the oil
  4. The viscosity of the oil
Show answer & solution

Answer: (C) The dielectric strength of the oil

Moisture and contaminants reduce BDV.

Question 22

Which solid insulation is commonly used on transformer windings immersed in oil?

  1. Glass bottles
  2. PVC tape only
  3. Rubber only
  4. Kraft paper and pressboard
Show answer & solution

Answer: (D) Kraft paper and pressboard

Oil-impregnated paper gives good insulation.

Question 23

How does moisture affect electrical insulation?

  1. It lowers insulation resistance and dielectric strength
  2. It improves insulation
  3. It increases breakdown voltage
  4. It has no effect
Show answer & solution

Answer: (A) It lowers insulation resistance and dielectric strength

Drying out is required for damp machines before energising.

Question 24

What is vacuum pressure impregnation (VPI) of windings?

  1. Impregnating windings with resin under vacuum and pressure to fill voids
  2. Testing insulation with a megger
  3. Painting the frame
  4. Cooling the windings with water
Show answer & solution

Answer: (A) Impregnating windings with resin under vacuum and pressure to fill voids

VPI improves insulation strength and heat transfer.

Question 25

Which type of bearing is most commonly used in small and medium induction motors?

  1. Wooden bearings
  2. Ball bearings
  3. Magnetic bearings only
  4. Plain glass bearings
Show answer & solution

Answer: (B) Ball bearings

Roller bearings are used for heavier radial loads.

Question 26

What is the main purpose of slot wedges in machine stators?

  1. To act as brushes
  2. To conduct current
  3. To cool the rotor
  4. To hold the coils firmly in the slots
Show answer & solution

Answer: (D) To hold the coils firmly in the slots

Magnetic wedges can also reduce losses.

Question 27

Which machine part provides a low-reluctance path for magnetic flux?

  1. The terminal box
  2. The insulation
  3. The laminated iron core
  4. The frame paint
Show answer & solution

Answer: (C) The laminated iron core

Low reluctance reduces magnetising current.

Question 28

What does the temperature rise rating of a machine refer to?

  1. The ambient temperature only
  2. The temperature of the room
  3. The allowed rise of winding temperature above the ambient temperature
  4. The bearing temperature only
Show answer & solution

Answer: (C) The allowed rise of winding temperature above the ambient temperature

Standards assume an ambient of 40 °C unless stated otherwise.

Question 29

Why are cooling ducts provided in large machine cores?

  1. To store oil
  2. To allow air or gas to remove heat from the core and windings
  3. To increase weight
  4. To reduce flux
Show answer & solution

Answer: (B) To allow air or gas to remove heat from the core and windings

Effective cooling allows a higher rating for a given size.

Question 30

What is hysteresis loss proportional to for a given magnetic material?

  1. The area of its hysteresis loop
  2. The length of the conductor
  3. The voltage squared only
  4. The current squared
Show answer & solution

Answer: (A) The area of its hysteresis loop

Soft magnetic materials have small loop areas.

Question 31

What is the main purpose of the end shields (end covers) of a motor?

  1. To support the bearings and enclose the machine
  2. To increase flux
  3. To insulate windings
  4. To carry current
Show answer & solution

Answer: (A) To support the bearings and enclose the machine

End shields locate the rotor in the stator bore.

Question 32

Why should a megger test be performed on a motor that has been idle in damp conditions?

  1. To measure speed
  2. To measure torque
  3. To check that insulation resistance is safe before energising
  4. To check frequency
Show answer & solution

Answer: (C) To check that insulation resistance is safe before energising

Low insulation resistance may require drying the windings.

Question 33

Which material is widely used as slot insulation in low-voltage motors?

  1. Copper foil
  2. Graphite
  3. Polyester film and Nomex-type laminates
  4. Steel sheet
Show answer & solution

Answer: (C) Polyester film and Nomex-type laminates

Slot liners separate windings from the core.

Question 34

Which property makes enamelled copper wire suitable for machine windings?

  1. Magnetic coating
  2. A thin, tough insulating coating on a good conductor
  3. Zero flexibility
  4. High resistance
Show answer & solution

Answer: (B) A thin, tough insulating coating on a good conductor

Enamel insulation saves slot space.

Practice these 34 questions interactively →