In which type of circuit can the superposition theorem be applied?
Show answer & solution
Answer: (D) Linear circuits with more than one independent source
Superposition relies on linearity.
Electrical Engineering · Circuit Analysis
37 questions, each with the answer and a worked solution.
Practice interactively and track your score →In which type of circuit can the superposition theorem be applied?
Answer: (D) Linear circuits with more than one independent source
Superposition relies on linearity.
When applying superposition, how are the other independent voltage sources deactivated?
Answer: (C) They are replaced by short circuits
Independent current sources are replaced by open circuits.
When applying superposition, how are the other independent current sources deactivated?
Answer: (D) They are replaced by open circuits
An open circuit means zero current.
Which quantity cannot be found directly by superposition?
Answer: (B) Power
Power is a non-linear (squared) function of current or voltage.
How is the Thevenin voltage of a network found?
Answer: (A) As the open-circuit voltage at the load terminals
Vth = Voc.
How is the Thevenin resistance of a network with only independent sources found?
Answer: (C) By deactivating all independent sources and finding the resistance seen at the terminals
Alternatively, Rth = Voc/Isc.
How is the Norton current of a network found?
Answer: (D) As the short-circuit current at the load terminals
IN = Isc.
How is the Norton equivalent circuit represented?
Answer: (B) A current source in parallel with a resistance
RN equals Rth.
What is the Thevenin resistance of a network with an open-circuit voltage of 12 V and a short-circuit current of 3 A?
Answer: (B) 4 Ω
Rth = Voc/Isc = 12/3 = 4 Ω.
What condition gives maximum power transfer to a resistive load from a DC network?
Answer: (D) Load resistance equals the Thevenin resistance
RL = Rth.
What is the maximum power delivered to a load from a network with Vth = 20 V and Rth = 5 Ω?
Answer: (B) 20 W
Pmax = Vth²/(4Rth) = 400/20 = 20 W.
What is the efficiency of power transfer under maximum power transfer conditions?
Answer: (B) 50%
Half the power is lost in the source resistance.
What load impedance gives maximum average power transfer in an AC circuit?
Answer: (C) The complex conjugate of the Thevenin impedance
ZL = Zth* cancels the reactance.
What does source transformation allow?
Answer: (A) A voltage source in series with R to be replaced by a current source V/R in parallel with R
It simplifies circuits without changing terminal behaviour.
What is the equivalent current source of a 10 V source in series with a 2 Ω resistor?
Answer: (B) 5 A in parallel with 2 Ω
I = V/R = 10/2 = 5 A.
What does the reciprocity theorem state?
Answer: (C) In a linear bilateral single-source network, the ratio of response to excitation stays the same when their positions are interchanged
It applies to networks with only one independent source.
Which theorem combines several parallel voltage sources with series resistances into one equivalent source?
Answer: (A) Millman's theorem
Millman's theorem simplifies parallel branches.
What does Tellegen's theorem state?
Answer: (D) The sum of the products of branch voltages and branch currents in any lumped network is zero
It holds for linear and non-linear networks alike.
Which theorem replaces a change in a branch impedance by an equivalent voltage source?
Answer: (C) Compensation theorem
It is used to find the effect of small changes in impedance.
What two properties together define a linear element or circuit?
Answer: (D) Homogeneity and additivity
Linearity allows superposition.
What is a bilateral element?
Answer: (A) An element with the same voltage–current relationship for current in either direction
Resistors are bilateral; diodes are unilateral.
Which element is an example of a non-linear element?
Answer: (D) Diode
Its current does not vary linearly with voltage.
What is an active circuit element?
Answer: (C) An element capable of delivering energy to the circuit
Voltage sources, current sources and amplifiers are active elements.
How is the Thevenin resistance found when a network contains dependent sources?
Answer: (A) By applying a test source at the terminals with independent sources deactivated and dependent sources kept
Rth = Vtest/Itest.
Which value of Thevenin resistance can occur only in networks containing dependent sources?
Answer: (D) Negative resistance
A negative Rth means the network can supply power.
What is the dual of an inductor in circuit duality?
Answer: (C) Capacitor
Duality also pairs series with parallel and KVL with KCL.
What is the dual of a short circuit?
Answer: (A) Open circuit
Voltage and current, series and parallel, are interchanged in the dual.
What is the dual of mesh analysis?
Answer: (C) Nodal analysis
Mesh currents correspond to node voltages in the dual network.
What is the equivalent delta resistance of each arm when three equal resistances of 10 Ω are connected in star?
Answer: (D) 30 Ω
For equal resistances, RΔ = 3RY.
What load resistance draws maximum power from a source with an internal resistance of 8 Ω?
Answer: (A) 8 Ω
Maximum power transfer occurs when RL equals the source resistance.
What is the Thevenin equivalent circuit?
Answer: (B) A voltage source in series with a resistance
Any linear two-terminal network can be replaced by this equivalent.
What is the condition for balance of a Wheatstone bridge with arms P, Q, R and S?
Answer: (B) P/Q = R/S
At balance, no current flows through the galvanometer.
In network graph theory, how many links does a connected graph with b branches and n nodes have?
Answer: (D) b − n + 1
A tree has n − 1 branches (twigs); the rest are links.
What does the node–branch incidence matrix of a network describe?
Answer: (A) Which branches are connected to which nodes and in what direction
It is used in systematic network formulation.
What is a tree in network graph theory?
Answer: (C) A connected subgraph containing all nodes and no closed loops
Each link added to a tree forms a fundamental loop.
What is the equivalent star impedance arm Ra between the arms Rb and Rc of a delta network with resistances Rab, Rbc and Rca?
Answer: (B) Ra = (Rab × Rca)/(Rab + Rbc + Rca)
Each star arm equals the product of adjacent delta arms divided by their sum.
What does the substitution theorem state?
Answer: (D) Any branch with known voltage or current can be replaced by an equivalent source without changing the rest of the circuit
It is useful for analysing parts of complex networks.