Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Strength of Materials: Torsion, Springs, Principal Stresses & Failure Theories

Civil Engineering · Strength of Materials

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Torsion of a shaft is the twisting caused by

  1. a torque (twisting moment) applied about the shaft axis
  2. a transverse shear force acting perpendicular to the axis
  3. an axial tensile load along the shaft axis
  4. a bending moment acting in a plane containing the axis
Show answer & solution

Answer: (A) a torque (twisting moment) applied about the shaft axis

Torsion results from a moment whose vector lies along the shaft axis.

Question 2

The torsion equation for a circular shaft is

  1. T/r = τ/J = θ/(GL)
  2. T/J = τ·r = Gθ/L
  3. T/J = τ/r = Gθ/L
  4. T/J = r/τ = L/(Gθ)
Show answer & solution

Answer: (C) T/J = τ/r = Gθ/L

T = torque, J = polar second moment of area, τ = shear stress at radius r, G = modulus of rigidity, θ = angle of twist over length L.

Question 3

In the torsion equation T/J = τ/r = Gθ/L, the symbol J denotes

  1. the angle of twist per unit length
  2. the modulus of rigidity of the shaft material
  3. the polar second moment of area of the shaft section
  4. the second moment of area about a diameter of the section
Show answer & solution

Answer: (C) the polar second moment of area of the shaft section

J = ∫r² dA is the geometric property governing torsional resistance.

Question 4

The polar second moment of area J of a solid circular shaft of diameter d is

  1. πd⁴/32
  2. πd⁴/16
  3. πd³/16
  4. πd⁴/64
Show answer & solution

Answer: (A) πd⁴/32

J = ∫₀^(d/2) 2πr³ dr = πd⁴/32 (πd⁴/64 is the second moment about a diameter).

Question 5

The polar second moment of area J of a hollow circular shaft of outer diameter D and inner diameter d is

  1. π(D³ − d³)/16
  2. π(D⁴ − d⁴)/32
  3. π(D⁴ − d⁴)/64
  4. π(D − d)⁴/32
Show answer & solution

Answer: (B) π(D⁴ − d⁴)/32

J of the hollow section is J(solid D) − J(solid d) = π(D⁴ − d⁴)/32.

Question 6

Under pure torsion, the shear stress in a solid circular shaft is

  1. maximum at the centre and zero at the outer surface, varying linearly with radius
  2. zero at the centre and maximum at the surface, varying linearly with radius
  3. uniform over the whole cross-section and equal to the outer-surface value
  4. zero at the centre and maximum at mid-radius, falling to zero at the surface
Show answer & solution

Answer: (B) zero at the centre and maximum at the surface, varying linearly with radius

τ = Tr/J is proportional to the radius r.

Question 7

A shaft of length L, polar second moment of area J and modulus of rigidity G carries a torque T. The angle of twist is

  1. θ = TJ/(GL)
  2. θ = TL/(EJ)
  3. θ = GJ/(TL)
  4. θ = TL/(GJ)
Show answer & solution

Answer: (D) θ = TL/(GJ)

From T/J = Gθ/L: θ = TL/(GJ), so twist grows with T and L and falls with GJ.

Question 8

A shaft rotating at angular speed ω (rad/s) transmits a torque T. The power transmitted is

  1. P = Tω
  2. P = T + ω
  3. P = Tω²
  4. P = T/ω
Show answer & solution

Answer: (A) P = Tω

Power = torque × angular velocity; with N rpm, ω = 2πN/60.

Question 9

For the same amount of material (equal cross-sectional area), a hollow circular shaft is better in torsion than a solid one because

  1. its larger outer radius reduces the polar second moment of area of the section
  2. material is moved outward, giving a larger J and lower maximum shear stress
  3. its modulus of rigidity is higher than that of a solid shaft
  4. the material near the centre carries the highest stress and is retained
Show answer & solution

Answer: (B) material is moved outward, giving a larger J and lower maximum shear stress

Material near the axis carries little torsional stress; relocating it outward increases J for the same area.

Question 10

The torsional rigidity of a shaft is

  1. GJ, modulus of rigidity times the polar second moment of area
  2. EJ, the product of Young's modulus and the polar second moment of area
  3. EI, the product of Young's modulus and the second moment of area
  4. GA, the product of the modulus of rigidity and the cross-sectional area
Show answer & solution

Answer: (A) GJ, modulus of rigidity times the polar second moment of area

GJ is the torsional counterpart of the flexural rigidity EI, since θ = TL/GJ.

Question 11

A shaft carries a bending moment M and a torque T together. The equivalent torque based on the maximum shear stress theory is

  1. Te = √(M² + T²)
  2. Te = M + T
  3. Te = ½[M + √(M² + T²)]
  4. Te = √(M² − T²)
Show answer & solution

Answer: (A) Te = √(M² + T²)

The maximum shear stress from combined bending and torsion corresponds to a pure torque √(M² + T²).

Question 12

A shaft carries a bending moment M and a torque T together. The equivalent bending moment based on the maximum principal stress theory is

  1. Me = ½[M + √(M² − T²)]
  2. Me = M + T
  3. Me = ½[M + T + √(M² + T²)]
  4. Me = ½[M + √(M² + T²)]
Show answer & solution

Answer: (D) Me = ½[M + √(M² + T²)]

The maximum principal stress is σ₁ = (σ + √(σ² + 4τ²))/2, which gives Me = ½[M + √(M² + T²)].

Question 13

A closely coiled helical spring carries an axial load. The stress in the wire is mainly

  1. bending stress
  2. direct tensile stress
  3. torsional shear stress
  4. direct crushing stress
Show answer & solution

Answer: (C) torsional shear stress

The axial load acts at a distance R from the wire axis, so the wire is twisted by a torque WR.

Question 14

The stiffness of a helical spring is

  1. the deflection produced by unit load
  2. the maximum shear stress in the wire at solid length
  3. the total strain energy stored at the proof load
  4. the load required to produce unit deflection
Show answer & solution

Answer: (D) the load required to produce unit deflection

k = load/deflection, measured in N/m.

Question 15

Two springs of stiffness k₁ and k₂ are connected in series. The combined stiffness is

  1. less than either stiffness, since 1/k = 1/k₁ + 1/k₂
  2. (k₁ + k₂)/2, the average of the two stiffnesses
  3. equal to the larger of k₁ and k₂
  4. k₁ + k₂, the sum of the two individual stiffnesses
Show answer & solution

Answer: (A) less than either stiffness, since 1/k = 1/k₁ + 1/k₂

In series the deflections add under the same load, so the combined stiffness is smaller than either; for k₁ = k₂ = k it is k/2.

Question 16

Two springs of stiffness k₁ and k₂ are connected in parallel. The combined stiffness is

  1. k₁k₂/(k₁ + k₂), since the deflections add
  2. the smaller of k₁ and k₂, since the weaker spring governs
  3. k₁ + k₂, as the deflections are equal and the loads add
  4. (k₁ + k₂)/2, the average of the two stiffnesses
Show answer & solution

Answer: (C) k₁ + k₂, as the deflections are equal and the loads add

Parallel springs share the load at equal deflection, so stiffnesses add.

Question 17

A transmission shaft carries power and is also subjected to bending from gears and pulleys. It should be designed for

  1. axial compressive stress alone, from the self-weight of the shaft
  2. torsional shear stress alone, since power transmission is the main load on it
  3. bending stress alone, since the torque is small by comparison with bending
  4. the combined effect of bending and torsion, via an equivalent torque or moment
Show answer & solution

Answer: (D) the combined effect of bending and torsion, via an equivalent torque or moment

Bending and torsion act together, so a combined-stress criterion (Te or Me) governs the design.

Question 18

In shaft design, 'rigidity design' as opposed to 'strength design' means designing for

  1. a limiting angle of twist per unit length instead of a stress limit
  2. the permissible shear stress at the outer surface of the shaft only
  3. the lowest possible mass per metre length of the shaft section
  4. the permissible bending stress at mid-span of the shaft only
Show answer & solution

Answer: (A) a limiting angle of twist per unit length instead of a stress limit

Rigidity design limits θ/L = T/(GJ), which can require a larger shaft than the stress limit does.

Question 19

In a shaft under pure torsion, the maximum tensile (principal) stress acts on a plane inclined to the shaft axis at

  1. 0°
  2. 30°
  3. 45°
  4. 90°
Show answer & solution

Answer: (C) 45°

Pure shear transforms to equal tensile and compressive principal stresses on planes at 45° to the shear planes (the shaft axis).

Question 20

A cast-iron shaft twisted to failure typically breaks along

  1. a plane at 30° to the axis, where tension and shear are equal
  2. a plane parallel to the axis through the centre of the section
  3. a helical surface at about 45° to the shaft axis
  4. a plane perpendicular to the axis, along the plane of maximum shear
Show answer & solution

Answer: (C) a helical surface at about 45° to the shaft axis

Brittle fracture follows the maximum principal tensile stress, which lies at 45° under pure torsion.

Question 21

Principal stresses at a point are

  1. the average of the normal stresses acting on any two perpendicular planes
  2. the maximum and minimum normal stresses, acting on planes of zero shear stress
  3. the normal stresses acting at the point on the planes of maximum shear stress
  4. the maximum and minimum shear stresses acting at the point on any plane
Show answer & solution

Answer: (B) the maximum and minimum normal stresses, acting on planes of zero shear stress

Principal planes carry normal stress only; the principal stresses are the extreme values of normal stress at the point.

Question 22

Mohr's circle is a graphical method for finding

  1. the buckling load of a column from its slenderness ratio
  2. principal stresses and maximum shear stress at a point
  3. the second moment of area of a composite section
  4. the deflection of a beam from its bending moment diagram
Show answer & solution

Answer: (B) principal stresses and maximum shear stress at a point

Mohr's circle is a graphical tool for 2D stress transformation.

Question 23

On Mohr's circle for plane stress, the centre lies at

  1. the maximum principal stress σ₁
  2. the origin, where the normal and shear stresses are zero
  3. the average normal stress (σx + σy)/2, with zero shear stress
  4. the maximum shear stress on the vertical axis
Show answer & solution

Answer: (C) the average normal stress (σx + σy)/2, with zero shear stress

The centre is on the normal-stress axis at (σx + σy)/2, and the circle's radius is the maximum in-plane shear stress.

Question 24

The radius of Mohr's circle for plane stress represents

  1. the average normal stress
  2. the sum of the two principal stresses
  3. the minimum principal stress
  4. the maximum in-plane shear stress
Show answer & solution

Answer: (D) the maximum in-plane shear stress

R = √[((σx − σy)/2)² + τ²] = (σ₁ − σ₂)/2 = τ_max.

Question 25

For plane stress with principal stresses σ₁ and σ₂, the maximum in-plane shear stress is

  1. τ_max = (σ₁ + σ₂)/2
  2. τ_max = (σ₁ − σ₂)/2
  3. τ_max = √(σ₁σ₂)
  4. τ_max = σ₁ − σ₂
Show answer & solution

Answer: (B) τ_max = (σ₁ − σ₂)/2

For example σ₁ = 80 MPa and σ₂ = −20 MPa give τ_max = 50 MPa.

Question 26

On the planes of maximum in-plane shear stress, the normal stress is

  1. equal to σ₂, the smaller principal stress
  2. (σ₁ + σ₂)/2, the average of the principal stresses
  3. equal to σ₁, the larger principal stress
  4. zero, because shear stress is maximum on these planes
Show answer & solution

Answer: (B) (σ₁ + σ₂)/2, the average of the principal stresses

These planes correspond to the top and bottom of Mohr's circle, at the centre abscissa (σ₁ + σ₂)/2.

Question 27

The planes of maximum shear stress are inclined to the principal planes at

  1. 22.5°
  2. 45°
  3. 60°
  4. 90°
Show answer & solution

Answer: (B) 45°

On Mohr's circle they are 90° apart, which is 45° apart in the physical element.

Question 28

A member in a state of pure shear stress τ has principal stresses equal to

  1. +τ/2 and −τ/2, on planes at 45° to the shear planes
  2. +τ and +τ, on planes at 45° to the shear planes
  3. zero and 2τ, on planes parallel to the shear planes
  4. +τ and −τ, on planes at 45° to the shear planes
Show answer & solution

Answer: (D) +τ and −τ, on planes at 45° to the shear planes

Mohr's circle for pure shear is centred at the origin with radius τ, so σ₁ = τ and σ₂ = −τ.

Question 29

The resultant stress at a fibre of a member under combined axial load and bending is obtained by

  1. taking the square root of the sum of the squares of the two stresses
  2. multiplying the direct stress by the bending stress
  3. taking the larger of the two stresses only
  4. algebraically adding the direct and bending stresses at that fibre
Show answer & solution

Answer: (D) algebraically adding the direct and bending stresses at that fibre

Within the elastic range, superposition gives σ = P/A ± My/I.

Question 30

The region of a cross-section within which a compressive load may act without producing tension anywhere in the section is called the

  1. core (kern) of the section
  2. neutral axis zone of the section
  3. plastic hinge region of the section
  4. shear centre of the section
Show answer & solution

Answer: (A) core (kern) of the section

Loads inside the kern keep the whole section in compression, which matters for masonry and other materials weak in tension.

Question 31

A rectangular column of depth d carries a compressive load applied at eccentricity e along the depth. No tension develops anywhere if e is not more than

  1. d/12
  2. d/8
  3. d/6
  4. d/3
Show answer & solution

Answer: (C) d/6

σ_min = (P/A)(1 − 6e/d) ≥ 0 gives e ≤ d/6 (the middle-third rule).

Question 32

The maximum principal stress theory (Rankine) states that failure occurs when

  1. the maximum principal stress reaches the simple-tension limiting stress
  2. the strain energy per unit volume reaches its value at yield in simple tension
  3. the maximum shear stress reaches the limiting stress of a simple tension test
  4. the largest principal strain reaches its value at yield in simple tension
Show answer & solution

Answer: (A) the maximum principal stress reaches the simple-tension limiting stress

Rankine's criterion is σ₁ ≥ σ_y (or σ_u), with no regard to the other principal stresses.

Question 33

The maximum shear stress theory (Tresca) states that failure occurs when

  1. the maximum principal strain reaches its value at yield in simple tension
  2. the maximum shear stress reaches the value it has at yield in simple tension
  3. the distortion energy per unit volume reaches its value at yield in simple tension
  4. the maximum principal stress reaches the yield stress in simple tension
Show answer & solution

Answer: (B) the maximum shear stress reaches the value it has at yield in simple tension

Tresca: τ_max = (σ₁ − σ₃)/2 ≥ σ_y/2.

Question 34

The maximum shear stress theory is best suited to

  1. ductile materials such as mild steel
  2. porous materials such as masonry
  3. brittle materials such as cast iron or glass
  4. brittle materials such as concrete
Show answer & solution

Answer: (A) ductile materials such as mild steel

Ductile metals yield by slip along shear planes, which matches the physical basis of the Tresca criterion.

Question 35

The maximum principal stress theory is best suited to

  1. materials that fail by yielding in shear, such as annealed copper
  2. ductile metals loaded mainly in shear, such as aluminium alloy
  3. brittle materials such as cast iron
  4. ductile materials such as mild steel
Show answer & solution

Answer: (C) brittle materials such as cast iron

Brittle fracture is governed by the largest tensile stress, as assumed in Rankine's theory.

Question 36

The distortion energy theory of failure is also known as the

  1. Saint-Venant (maximum strain) theory
  2. Rankine (maximum principal stress) theory
  3. von Mises (Huber-Hencky) theory
  4. Tresca (maximum shear stress) theory
Show answer & solution

Answer: (C) von Mises (Huber-Hencky) theory

von Mises-Hencky: yielding starts when the distortion (shape-change) energy equals that at yield in simple tension.

Question 37

The maximum principal strain theory of failure is also known as the

  1. Haigh (energy) theory
  2. Saint-Venant theory
  3. Rankine (maximum stress) theory
  4. von Mises (distortion) theory
Show answer & solution

Answer: (B) Saint-Venant theory

Saint-Venant limits the largest principal strain, whereas Rankine limits the largest principal stress.

Question 38

The total strain energy theory of failure is also known as the

  1. Guest theory
  2. Rankine theory
  3. Saint-Venant theory
  4. Haigh (Beltrami–Haigh) theory
Show answer & solution

Answer: (D) Haigh (Beltrami–Haigh) theory

Haigh's theory limits the total strain energy per unit volume; Guest's theory is another name for the maximum shear stress theory.

Question 39

For ductile metals, the failure theory that generally agrees best with experimental yield data is the

  1. total strain energy (Haigh) theory
  2. maximum principal stress (Rankine) theory
  3. maximum principal strain (Saint-Venant) theory
  4. distortion energy (von Mises) theory
Show answer & solution

Answer: (D) distortion energy (von Mises) theory

Tests on ductile metals under combined stress match the von Mises criterion most closely.

Question 40

In a simple uniaxial tension test, the Rankine, Tresca and von Mises criteria all predict yielding or failure at

  1. a stress equal to half the yield stress for the shear-based theories
  2. different stresses, with Tresca giving the lowest
  3. stresses that differ by a factor of two
  4. the same stress, the yield or ultimate stress found in the test
Show answer & solution

Answer: (D) the same stress, the yield or ultimate stress found in the test

Each theory is calibrated against the simple tension test, so they necessarily agree there.

Practice these 40 questions interactively →